Microsoft Word S028393e doc Reference number ISO 15612 2004(E) © ISO 2004 INTERNATIONAL STANDARD ISO 15612 First edition 2004 08 01 Specification and qualification of welding procedures for metallic m[.]
Trang 1Reference number
First edition 2004-08-01
Specification and qualification of welding procedures for metallic materials —
Qualification by adoption of a standard welding procedure
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Qualification par référence à un mode opératoire de soudage standard
Trang 2PDF disclaimer
This PDF file may contain embedded typefaces In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy The ISO Central Secretariat accepts no liability in this area
Adobe is a trademark of Adobe Systems Incorporated
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing Every care has been taken to ensure that the file is suitable for use by ISO member bodies In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below
© ISO 2004
All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
Copyright International Organization for Standardization
Reproduced by IHS under license with ISO
Trang 3
``````-`-`,,`,,`,`,,` -Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2
The main task of technical committees is to prepare International Standards Draft International Standards adopted by the technical committees are circulated to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights
ISO 15612 was prepared by the European Committee for Standardization (CEN) in collaboration with
Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement)
This first edition of ISO 15612 cancels and replaces ISO 9956-7:1995, of which it constitutes a technical revision
Throughout the text of this document, read “ this European Standard ” to mean “ this International Standard ”
Annex ZA provides a list of corresponding International and European Standards for which equivalents are not given in the text
Trang 4``````-`-`,,`,,`,`,,` -iv © ISO 2004 – All rights reserved
Foreword v
Introduction vi
1 Scope 1
2 Normative references 1
3 Terms and definitions 2
4 Preliminary welding procedure specification (pWPS) 2
5 Qualification by adoption of the standard welding procedure 2
5.1 General 2
5.2 Parent metal 2
6 Use of a standard welding procedure 3
6.1 General 3
6.2 Related to the user of a standard welding procedure 3
6.3 Related to the welding equipment 3
6.4 Related to the personnel 3
7 Validity 4
8 Preparation and documentation 4
Annex ZA (normative) Normative references to international publications with their relevant European publications 5
Bibliography 6
Copyright International Organization for Standardization Reproduced by IHS under license with ISO
Trang 5``````-`-`,,`,,`,`,,` -Foreword
This document (EN ISO 15612:2004) has been prepared by Technical Committee CEN/TC 121 “Welding”, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 44 “Welding and allied processes”
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by February 2005, and conflicting national standards shall be withdrawn at the latest
by February 2005
This document supersedes EN 288-7:1995
Normative references to International Standards are listed in annex ZA
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom
Trang 6``````-`-`,,`,,`,`,,` -vi © ISO 2004 – All rights reserved
Introduction
In EN ISO 15607, one of the methods of welding procedure qualification is by adoption of a standard welding procedure
Copyright International Organization for Standardization
Reproduced by IHS under license with ISO
Trang 7``````-`-`,,`,,`,`,,` -1 Scope
This standard gives the necessary information to explain the requirements referenced in EN ISO 15607 about the qualification by adoption of a standard welding procedure, and establishes the conditions, limits and ranges of qualification necessary for the use of a standard welding procedure
This standard gives the manufacturer the possibility to use welding procedures based on welding procedure tests performed by other organisations
This standard is a part of a series of standards, details of this series are given in EN ISO 15607:2003, annex A The use of this standard can be restricted by an application standard or a specification
2 Normative references
The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies
EN 287-1,Qualification test of welders - Fusion welding - Part 1: Steels
EN 287-2, Approval testing of welders — Fusion welding — Part 2 : Aluminium and aluminium alloys
EN 719, Welding coordination — Tasks and responsibilities
EN 729-1, Quality requirements for welding — Fusion welding of metallic materials — Part 1: Guidelines for selection and use
EN 729-2, Quality requirements for welding — Fusion welding of metallic materials — Part 2: Comprehensive quality requirements
EN 729-3, Quality requirements for welding — Fusion welding of metallic materials — Part 3: Standard quality requirements
EN 729-4, Quality requirements for welding — Fusion welding of metallic materials — Part 4: Elementary quality requirements
EN 1418, Welding personnel — Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
EN ISO 9606-3, Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys (ISO 9606-3:1999)
(ISO 9606-4:1999)
EN ISO 9606-5, Approval testing of welders — Fusion welding — Part 5: Titanium and titanium alloys, zirconium and zirconium alloys (ISO 9606-5:2000)
EN ISO 15607:2003, Specification and qualification of welding procedures for metallic materials — General rules (ISO 15607:2003)
Trang 8``````-`-`,,`,,`,`,,` -2 © ISO 2004 – All rights reserved
EN ISO 15609-1, Specification and approval of welding procedures for metallic materials — Welding procedure specification — Part 1: Arc welding (ISO 15609-1:2004)
EN ISO 15609-2, Specification and qualification of welding procedures for metallic materials — Welding procedure specification — Part 2: Gas welding (ISO 15609-2:2001)
EN ISO 15609-3, Specification and qualification of welding procedures for metallic materials — Welding procedure specification — Part 3: Electron beam welding (ISO 15609-3:2004)
EN ISO 15609-4, Specification and qualification of welding procedures for metallic materials — Welding procedure specification — Part 4: Laser beam welding (ISO 15609-4:2004)
EN ISO 15614 (all parts), Specification and qualification of welding procedures for metallic materials — Welding procedure test
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN ISO 15607:2003 apply
4 Preliminary welding procedure specification (pWPS)
The qualification by adoption of a standard welding procedure shall be based on a pWPS according to the appropriate part of EN ISO 15609 This pWPS shall specify the range for all the relevant parameters
5 Qualification by adoption of the standard welding procedure
5.1 General
The qualification of the welding procedure shall be carried out by an examiner or an examiner body according to
EN ISO 15607 It shall be verified that examination and testing have been carried out in accordance with the appropriate part of EN ISO 15614
After qualification, the preliminary welding procedure specification will be considered as a standard welding procedure specification
Changes outside the range of qualification given in the appropriate part of EN ISO 15614 as modified in 5.2 shall require a new qualification welding procedure
The welding procedure shall be qualified by the manufacturer and if applicable, verified by an examiner or examining body in accordance with EN ISO 15607
5.2 Parent metal
This standard is applicable for parent material groups defined in Table 1
Copyright International Organization for Standardization
Reproduced by IHS under license with ISO
Trang 9
``````-`-`,,`,,`,`,,` -Table 1 — Applicable parent material groups
Parent material groups used for the qualification
of the welding procedure
Range of qualification
1-1 1-1
1 - 11
11 – 11
22.2 - 22.2 22.1 - 22.2
material
material
a excluding those alloys which are extremely sensitive to hot cracking
6 Use of a standard welding procedure
6.1 General
A standard welding procedure prepared and documented in accordance with clause 8 can be used without further tests providing the following requirements and limitations are observed
6.2 Related to the user of a standard welding procedure
The user of a standard welding procedure is responsible for the appropriate selection and application of the standard welding procedure
The use of a standard welding procedure requires welding coordination in accordance with EN 719 and that the user fulfils quality requirements in accordance with the appropriate part of EN 729
6.3 Related to the welding equipment
The standard welding procedure is qualified for use in production with welding power sources and welding equipment having electrical and mechanical characteristics which are capable of achieving those used in preparing the test weld for qualification of the standard welding procedure as specified in the welding procedure specification WPS
The equipment used during production shall permit control of all essential welding parameters
6.4 Related to the personnel
A standard welding procedure shall only be used by welders or welding operators for mechanized equipment qualified in accordance with the relevant part of EN 287 or EN ISO 9606 or EN 1418
Trang 104 © ISO 2004 – All rights reserved
7 Validity
A standard welding procedure remains valid until it is withdrawn or revised
8 Preparation and documentation
The standard welding procedure shall be issued as a specification covering ranges for all relevant parameters Any restrictions, e.g equipment performance or environmental conditions, shall be stated, as appropriate The specification shall be in the format of a welding procedure qualification record WPQR according to the relevant part
of prEN ISO 15614
The new WPS shall be signed and dated by the manufacturer and, if applicable, verified by an examiner or examining body Any amendments or revisions shall be re-qualified All records on which the qualification is based shall be traceable to the original source during the entire period of its use
Copyright International Organization for Standardization
Reproduced by IHS under license with ISO
Trang 11
``````-`-`,,`,,`,`,,` -Annex ZA
(normative)
Normative references to international publications with their relevant
European publications
This European Standard incorporates by dated or undated reference, provisions from other publications These normative references are cited at the appropriate places in the text and the publications are listed hereafter For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or revision For undated references the latest edition of the publication referred to applies (including amendments)
NOTE Where an International Publication has been modified by common modifications, indicated by (mod.), the relevant EN/HD applies
Publication Year Title EN Year
Fusion welding of metallic materials
— Part 1: Guidelines for selection and use
EN 729-1
Fusion welding of metallic materials
— Part 2: Comprehensive quality requirements
EN 729-2
Fusion welding of metallic materials
— Part 3: Standards quality requirements
EN 729-3
Fusion welding of metallic materials
— Part 4: Elementary quality requirements
EN 729-4
testing of welding operators for fusion welding and of resistance weld setters for fully mechanized and automatic welding of metallic materials
EN 1418
Trang 12``````-`-`,,`,,`,`,,` -6 © ISO 2004 – All rights reserved
Bibliography
CR ISO 15608, Welding — Guidelines for a metallic material grouping system (ISO/TR 15608:2000)
Copyright International Organization for Standardization
Reproduced by IHS under license with ISO
Trang 14``````-`-`,,`,,`,`,,` -ICS 25.160.10
Price based on 6 pages
© ISO 2004 – All rights reserved
Copyright International Organization for Standardization
Reproduced by IHS under license with ISO