© ISO 2014 Aerospace series — Graphic symbols for schematic drawings of hydraulic and pneumatic systems and components Série aérospatiale — Symboles graphiques pour schémas de circuits de transmission[.]
Trang 1© ISO 2014
Aerospace series — Graphic symbols for schematic drawings of hydraulic and pneumatic systems and
components
Série aérospatiale — Symboles graphiques pour schémas de circuits
de transmissions hydrauliques et pneumatiques
Second edition 2014-03-01
Reference number ISO 5859:2014(E)
Copyright International Organization for Standardization
Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Trang 2
`,```,,`,,`,`,``,,,,`,`,`,```-`-`,,`,,`,`,,` -ISO 5859:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
Copyright International Organization for Standardization
Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Trang 3
`,```,,`,,`,`,``,,,,`,`,`,```-`-`,,`,,`,`,,` -© ISO 2014 – All rights reserved iii
Foreword iv
1 Scope 1
2 Normative references 1
3 Requirements 1
4 Identification statement 1
5 Revision of SAE AS 1290 B 1
Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Trang 4`,```,,`,,`,`,``,,,,`,`,`,```-`-`,,`,,`,`,,` -ISO 5859:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies) The work of preparing International Standards is normally carried out through ISO technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1 In particular the different approval criteria needed for the different types of ISO documents should be noted This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives)
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights ISO shall not be held responsible for identifying any or all such patent rights Details of any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents)
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 20, Aircraft and space vehicles, Subcommittee
SC 10, Aerospace fluid systems and components.
This second edition cancels and replaces the first edition (ISO 5859:1991), which takes into account revision B of SAE AS 1290
Copyright International Organization for Standardization
Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Trang 5`,```,,`,,`,`,``,,,,`,`,`,```-`-`,,`,,`,`,,` -Aerospace series — Graphic symbols for schematic
drawings of hydraulic and pneumatic systems and
components
1 Scope
This International Standard establishes a system of graphic symbols of hydraulic and pneumatic circuits and components for all types of aerospace systems
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies
SAE AS 1290 B, Graphic Symbols for Aircraft Hydraulic and Pneumatic Systems1)
3 Requirements
Requirements are specified in SAE AS 1290 B, which is a revision of SAE AS 1290 A, which is adopted as
a de facto ISO International Standard.
4 Identification statement
Use the following statement when electing to comply with ISO 5859:
“Graphic symbols are in accordance with ISO 5859, Aerospace series — Graphic symbols for schematic
drawings of hydraulic and pneumatic systems and components.”
5 Revision of SAE AS 1290 B
It has been agreed with the SAE that Technical Committee ISO/TC 20/SC 10 will be consulted in the event of any revision or amendment of SAE AS 1290 B
1) Copies of the original text in English are available from SAE International, 400 Commonwealth Drive, Warrendale,
PA, 15096-0001, USA
Copyright International Organization for Standardization
Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Trang 6
`,```,,`,,`,`,``,,,,`,`,`,```-`-`,,`,,`,`,,` -ISO 5859:2014(E)
© ISO 2014 – All rights reserved
ICS 01.080.30;49.080
Price based on 1 page
Copyright International Organization for Standardization
Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs