Shop Manual & ETM BCM KIA Cerato 2010 - Power Door Locks

Tài liệu Shop Manual & ETM BCM KIA Cerato 2010

2010 > G 1.6 DOHC > Body Electrical System

Component Location

1 ICM relay box (Door lock/unlock relay)

2 Body control module (BCM)

3 Front door lock actuator & switch

4 Rear door lock actuator & switch

5 Trunk lid actuator & switch

6 Door lock knob

7 Door lock switch

8 Passenger compartment junction box (Trunk lid relay)

2010 > G 1.6 DOHC > Body Electrical System

Inspection

Front Door Lock Actuator

Language

Language

1 Remove the front door trim.

(Refer to the Body group - Front door)

2 Remove the front door module

(Refer to the Body group - Front door)

3 Disconnect the connectors from the actuator

[LHD]

[RHD]

4 Check actuator operation by connecting power and ground according to the table To prevent damage

to the actuator, apply battery voltage only momentarily

Rear Door Lock Actuator

1 Remove the rear door trim

(Refer to the Body group - Rear door)

2 Remove the rear door module.

(Refer to the Body group - Rear door)

3 Disconnect the connectors from the actuator

[LHD]

[RHD]

4 Check actuator operation by connecting power and ground according to the table To prevent damage

to the actuator, apply battery voltage only momentarily

Trunk lid Lock Actuator Inspection

1 Remove the trunk trim (Refer to the Body group - trunk)

2 Disconnect the 3P connector from the actuator

3 Check actuator operation by connecting power and ground according to the table To prevent damage

to the actuator, apply battery voltage only momentarily

Front Door Lock Switch

1 Remove the front door trim

(Refer to the Body group - Front door)

2 Remove the front door module

(Refer to the Body group - Front door)

3 Disconnect the connectors from the actuator

[LHD]

[RHD]

4 Check for continuity between the terminals in each switch position when inserting the key into the door according to the table

Rear Door Lock Switch

1 Remove the rear door trim

(Refer to the Body group - Rear door)

2 Remove the rear door module

(Refer to the Body group - Rear door)

3 Disconnect the connectors from the actuator

[LHD]

4 Check for continuity between the terminals in each switch position according to the table

Trunk lid Switch

1 Remove the trunk trim (Refer to the Body group - Trunk)

2 Disconnect the 3P connector from the actuator

3 Check for continuity between the terminals in each switch position according to the table.

2010 > G 1.6 DOHC > Body Electrical System

Inspection

Door Lock

1 Disconnect the negative (-) battery terminal

2 Remove the ICM relay box

3 Check for continuity between the terminals

4 There should be continuity between the No.5 terminal and No.4 terminals in the ICM-B when power and ground are connected to the No.11 terminal and No.13 terminal in the ICM-B

5 There should be no continuity between the No.5 terminal and No.14 terminal in the ICM-B when power

is disconnected

Language

Door Unlock

1 Disconnect the negative (-) battery terminal

2 Remove the ICM relay box

3 Check for continuity between the terminals

4 There should be continuity between the No.4 terminal and No.14 terminal in the ICM-B when power and ground are connected to the No.10 terminal and No.13 terminal in the ICM-B

5 There should be no continuity between the No.4 terminal and No.14 terminal in the ICM-B when power

is disconnected

Trunk Open

1 Disconnect the negative (-) battery terminal

2 Remove the passenger compartment junction box

3 Check for continuity between the terminals

4 There should be continuity between the No.3 terminal in the I/P-H and the No.2 terminal in the I/P-D when power and ground are connected to the No.3 terminal in the I/P-H and the No.28 terminal in the I/P-F

5 There should be no continuity between the No.3 terminal in the I/P-H and the No.2 terminal in the I/P-D when power and ground are connected to the No.3 terminal in the I/P-H and the No.28 terminal in the I/P-F

2010 > G 1.6 DOHC > Body Electrical System

Inspection

Driver Door Lock Switch

1 Disconnect the negative (-) battery terminal

2 Remove the front door trim and power window switch (Refer to the Body group - "front door")

[LHD]

[RHD]

3 Remove the power window switch module after removing the screws

Language

Be careful not to damage the hooks when removing the switch module.

4 Check for continuity between the terminals in each switch position according to the table

[Auto Up & Down]

[Auto Down]