Tiêu chuẩn iso 10889 7 2016

© ISO 2016 Tool holders with cylindrical shank — Part 7 Type F with taper seat Porte outil à queue cylindrique — Partie 7 Porte outil de type F pour outils à queue conique INTERNATIONAL STANDARD ISO 1[.]

Tool holders w ith cylindrical shank —

Part 7:

Porte-o til à q eue c ylindrique —

Partie 7: Porte-o til de ty e Fp ur o tils à q eue co ique

T ir d edition

2 16-0 -1

Reference n mb r

ISO 1 8 9-7:2 16(E)

COPYRIGHT PROTECTED DOCUMENT

© ISO 2016, P blshed in Sw itz rlan

A ll rig hts r eserved Unles otherw ise spe ified, nopar of this p blc tion ma y be r epr od c d or utilz d otherw ise in an form

or b an me ns, ele tr onic or me hanic l, inclu in p oto opying , or postin on the internet or an intranet , w ithout prior

written permis ion Permis ion c n be req esed from either ISO at the ad r es below or ISO’s member bod y in the c u try of

F reword i v

1 Sc ope 1

2 Nor mati ve r eferenc es 1

3 Dimensions 1

4 Desig natio 3

5 Technical deli very c onditio s 3

A nne x A (informative)Relatio ship betwe n desig natio s in this part of ISO 10 89 and ISO 13399 4

Biblog raphy

5

ISO (he Int ernational Org nization for Stan ardization) is a worldwidefede ation of national s an ards

b dies (ISO membe b dies) The work of pr p ring Int ernational Stan ards is normaly car ied out

through ISO t ech ical committ ees Each membe b dy int er st ed in a subje t for w hich a t ech ical

committ ee has be n es a lshed has the right t o be r pr sent ed on that committ ee Int ernational

org nizations, g ove nmental an non-g ove nmental, in laison with ISO, also take part in the work

ISO cola orat es closely with the Int ernational Ele trot ech ical C mmis ion (IEC) on al matt ers of

ele trot ech ical s an ardization

The proc d r s used t o develo this document an those int en ed for it furthe maint enanc ar

desc ibed in the ISO/IEC Dir ctives, Part 1 In p rticular the dife ent a pro al c it eria ne ded for the

dife ent ty es of ISO document should be not ed This document was draft ed in ac ordanc with the

edit orial rules of the ISO/IEC Dir ctives, Part 2 ( e www.iso.org dir ctives)

A tt ention is drawn t o the p s ibi ity that some of the element of this document ma be the subje t of

p t ent right ISO shal not be held r sponsible for identifying any or al such p t ent right Detais of

any p t ent right identified d ring the develo ment of the document wi be in the Introd ction an / r

on the ISO ls of p t ent de larations r c ived ( e www.iso.org p t ent )

Any trade name used in this document is information given for the convenienc of use s an does not

cons itut e an en orsement

F or an ex lanation on the meaning of ISO spe ific t erms an ex r s ions r lat ed t o conformity

as es ment, as wel as information a out ISO’ s adhe enc t o the WTO principles in the Te h ical

Bar ie s t o Trade (TBT) se the fol owing URL: F or word - Sup lementary information

The committ ee r sp nsible for this document is ISO/TC 2 , Smal to ls , Subcommitt ee SC 2, Holdin

to l s, ada ti ve items a d inte fces

This third edition canc ls an r plac s the se on edition (ISO 1 8 9-7 :2 04 ), of w hich it cons itut es

a minor r vision, nota ly with the ad ition of Annex A, w hich gives the r lationship betwe n the

designations of this p rt of ISO 1 88 an the ISO 1 3 9 se ies

ISO 1 8 9 consis sof thefolowing p rt , un e the g ene al title To l h lde s w ith cylndric al sha k :

— Part 1: Cylndric al sha k, loc atio b r — Technic al deli ve y c onditions

— Part 2 : Ty pe A, sha k s fr to l h lde s o s pec ial des ig s

— Part 3 : Ty pe B w ith r c ta g lar radial seat

— Part 4 : Ty pe C w ith r c ta g lar ax ial s eat

— Part 5: Type D w ith mor th n o e r c ta g lar s eat

— Part 6 : Type E w ith cylndric al s eat

— Part 7: Ty pe F w ith ta e s eat

— Part 8: Type Z, ac c es sories

Tool holders with cylindrical shank —

Part 7:

This part of ISO 1 88 spe ifies dimensions, designations, an complementary t ech ical del ve y

con itions for t ool holde s with ta e seat of ty e F an with a cy lin rical shan mou ting sy st em in

ac ordanc with ISO 1 8 9-1

ISO 1 8 9is a pl ca le t o t ool holde s with cy lin rical shan for machine t ools with non-rotating t ools,

pr fe a ly for turning machines

F r non-s an ardiz d to l holde s with tape seat such as the tool holde s shown in Fig ur 1, it is

advisa le t o a ply the cor esp n ing spe if ications of this p rt of ISO 1 8 9

2 Normati ve referenc es

The folowing document , in w hole or in p rt, ar normatively r fe enc d in this document an ar

in ispensa le for it a plcation F or dat ed r fe enc s, only the edition cit ed a ples F or un at ed

r fe enc s, the lat es edition of the r fe enc d document ( inclu ing any amen ment )a pl es

ISO 2 6, Machine to ls — Self-h ldin ta e s fr to l sha k s

ISO 2768-1, G ene al tole a c es — Part 1: Tole a c es fr lnear a d a g lar dimens io s w ith ut indi v idu l

tole a c e indic atio s

ISO 2768- 2, G ene al tole a c es — Part 2 : G eometric al tole a c es fr featur s w ith ut indi v idu l tole a c e

indic atio s

ISO 1 8 9-1, To l h lde s w ith cylndric al sha k — Part 1: Cylndric al sha k, loc atio b r — Technic al

deli ve y c onditio s

Al dimensions an t ole anc s ar given in mi lmetr s Tole ancing is done ac ording t o ISO 80 5

Tole anc s not spe ified shal be of t ole anc clas “ m” in ac ordanc with ISO 27 68-1 an of clas “H”

in ac ordanc with ISO 2768- 2

Unspe if ied detai s shal be chosen a pro riat ely

The dimensions of t ool holde s ty e F shal be in ac ordanc with the dimensions shown in Figur 1

an given in Ta le 1

The r lationship betwe n the symbols of this p rt of ISO 1 8 9 an the symb ls ac ording t o ISO 1 3 9

is given in Annex A

Dimensions in milimetr es

a

b

c

? 0,0

? d₅

? d₂ l₁

l₂

l₃

Key

a

C lin rical shan in ac or dance w ith ISO 1 8 9-1

b

InternalMor e taper, type BIK in ac or dance w ith ISO 2 6

c

Ex ternal co lant su ply (closa le)

Figure 1 — Tape se t ty e F tool h lde for tape shanks with flat tang

Table 1 — Ty e F tool holde dimensio s

Dimensions in milimetr es

d

1

Int ernal

Morse

ta e ,

ty e BIK No

d

2

d

3

d

4 d

5 h

1 h

2 l

1

l

2

l

3

l

4

a

2

1

5

48

—

3

1

68

—

5

—

a

4

2

8

36

—

a

1

Int ernal

Morse

ta e ,

ty e BIK No

d

2

d

3

d

4 d

5 h

1 h

2 l

1

l

2

l

3

l

4

6

3

1 3

36

—

a

8

4

1 8

—

a

These siz s have a re es for taper shan s with flat an u to the en fa e of the cyln ric l shan The desig of slot is

at the discretion of the man fa turer

4 Desig nation

A ty e F t ool holde with Morse ta e seat in ac ordanc with this p rt of ISO 1 88 shal be designat ed

b the folowing:

a) “t ool holde ” ;

b) r fe enc t o this p rt of ISO 1 88 , i.e ISO 1 8 9-7 ;

c) ty e (F);

d) nominal diamet er, d

1 , in mi lmetr s;

e) int ernal ta e ty e;

f) if a plca le, hardened contact urfac (H)

E AMP E 1 A ty e F to l holder with a Mor e taper se t, a nominal diameter, d

1

= 40 mm, an an int ernal

taper, ty e BIK 3, is designated as folows:

To l holder ISO 1 889-7 - F - 40 - MT-BIK 3

E AMP E 2 A ty e F to l holder with a Mor e taper se t an nominal diameter, d

1

=40 mm, an internal taper,

ty e BIK 3, an hardened contact surface is designated as folows:

Tool h lder ISO 1 889-7 - F - 40 - MT-BIK 3 H

5 Technical deli very c onditions

As a complement t o the r q ir ment of ISO 1 88 -1, the folowing r q ir ment also a ply

The ta e socket shal be hardened with a surfac hard es of (5

0 4 +

) HRCan a depth of hardening of

at leas 0,5 mm

The ta e anglet ole anc clas of ta e socket shal be AT5 in ac ordanc with ISO 2 6

To l holde s can also be sup led with hardened contact surfac

Table 1 (c ontin ed)

A nnex A

ISO 13399

F or the r lationship betwe n the symb ls of this p rt of ISO 1 88 an the symb ls ac ording t o

ISO 1 3 9, se Ta le A.1

Table A.1 — Relatio ship betwe n symb ls in this part of ISO 1 889 and ISO 13399

Symb l in

this p rt of

ISO 1 8 9

R efe enc in this

p rt of

ISO 1 8 9

Pro e ty

name in

ISO 1 3 9 se ies

Symb l in

ISO 1 3 9 se ies

R efe enc in

ISO 1 3 9 se ies

BSU code

d

1

Figure 1 con ection

diameter machine

side

d

2

d

3

Figure 1 fu ctional

diamet er

d

4

d

5

l

1

l

2

l

3

l

4

h

1

a

h

2

a

O His the “overal heig t” (c de BSU 71D0 8 B 3E 7)

Bibl og raphy

[1] ISO 8 1 , Ge ome trical produc t spe cificatio s (GPS) — Fu dame ntals — Co ce pts , principles a d rules

[2] ISO 1 3 9(al p rt ), Cut in to l data r pr sentatio a d excha ge