Tài liệu OMX600 Optical Distribution Frame pdf

5/07 • 103742AE Fiber Distributing Cabinets The OMX600® fiber distributing cabinet provides mounting locations for termination, splice and storage panels.. 5/07 • 103742AE Preterminated

5/07 • 103742AE

Introduction 94

Things to Consider When Ordering 96

Fiber Distributing Cabinets 97

Preterminated Fiber Termination Panels with Pigtails 98

Preterminated Fiber Termination Panels with Multifiber Cable-IFC 99

Adapter-Only Fiber Termination Panels 100

Splice Panels 101

Value-Added Module (VAM) Chassis 102

Jumper Storage Panel 103

Interbay Management Panel 103

Frame Installation Kit 103

End Guard 103

Splice Frame 104

Splice Tray 105

Cable Clamp 105

Standard Cross-Connect Patch Cord Lengths 106

Ordering Information for Patch Cords and Attenuators 106

5/07 • 103742AE

Introduction

Termination Panel

The OMX600 termination panels are available with 72, 96 or 144 (with LC) adapters These panels can be ordered with adapters only or preterminated with either intrafacility (IFC), outside plant (OSP) cables or pigtails for ease of installation The panels are available with industry-standard connector/adapter styles

Splice Panel

The OMX600 splice panel provides protection and a mounting location for ADC’s round splice trays Each splice panel is two mounting positions tall and holds 24 splice trays Each splice tray can house up to 24 splices

Storage Panel

The storage panel enables storage of fiber-optic jumper slack within an OMX600 frame Each jumper storage module is one module position tall The interbay management panel provides off-frame storage of jumper slack ADC recommends the use of 2.0 mm patch cords to maximize the cable management potential

Value-Added Module (VAM) Chassis

Adding signal management and enhancement functions, such as splitters, couplers and wavelength division mulitplexers, optimizes the value of your fiber network, by providing nonintrusive access to the optical signal for monitoring and testing signal integrity The OMX600 VAM chassis accommodates various splitter and WDM modules

ADC has developed the OMX600® optical distribution frame to meet today‘s network demands Designed with total front access, the OMX600 has five right-hand and five left-hand mounting positions and can be installed back-to-back or against a wall to save valuable office floor space

This high-density frame terminates and splices up to 576 fibers in a

600 mm x 300 mm (23.6" x 11.8") footprint

Product Overview

Limited floor space where versatility is a necessity

Number of fibers, future growth potential

Termination panels 72, 96 and 144 (LC connectors only)

5/07 • 103742AE

Introduction

Configurations

The modular OMX600® product line can be configured to optimize the network All OMX600

configurations listed below are completely front-facing, enabling wall-mount or back-to-back

configurations The OMX600 can be enclosed with lockable front doors and end guards for increased

fiber protection and security

Configuration 1

576 terminations and 576 splices (using the 96-position panel)

432 terminations and 432 splices (using the 72-position panel) 2.14 m x 900 mm x 300 mm (7' x 35.4" x 11.8")

Interconnect or cross-connect solution Includes two off-frame jumper storage panels

Configuration 2

288 terminations and 288 splices (using the 96-position panel)

216 terminations and 216 splices (using the 72-position panel) 2.14 m mm x 600 mm x 300 mm (7' x 23.6" x 11.8") Interconnect solution

On-frame jumper storage

Other configurations are available upon request Please contact ADC Technical Assistance Center

Configuration 4

576 terminations and 288 splices (using the 96-position panel)

432 terminations and 216 splices (using the 72-position panel) 2.14 m x 600 mm x 300 mm (7' x 23.6" x 11.8")

Cross-connect solution On-frame jumper storage

Configuration 3

480 terminations (using the 96-position panel)

360 terminations (using the 72-position panel) 2.14 m x 600 mm x 300 mm (7' x 23.6" x 11.8") Interconnect or cross-connect solution

On-frame jumper storage

5/07 • 103742AE

Things to Consider When Ordering How to Order

1) Select desired Frame

- Fiber Distributing Cabinet - Page 97 _

2) Select desired Fiber Termination Panels

- Preterminated Fiber Termination Panels with

- Preterminated Fiber Termination Panels with Multifiber Cable-IFC - Page 99 _

- Adapter-Only Fiber Termination Panels - Page 100 _

- Splice Panels - Page 101 _

Optional Equipment

3) Value-Added Module (VAM) Chassis - Page 102 _ 4) Jumper Storage Panel - Page 103 _ 5) Interbay Management Panel - Page 103 _ 6) Frame Installation Kit - Page 103 _

10) Patch Cord - Pages 122–126* _ 11) In-Line Attenuator - Page 127 _

*See page 106 for standard cross-connect patch cord lengths

5/07 • 103742AE

Fiber Distributing Cabinets

The OMX600® fiber distributing cabinet provides mounting locations for termination, splice and storage

panels It is a completely front-facing frame; all mounting, maintenance and cable access is done on the front of the frame A lower trough allows multiple frames to be mounted in a continuous lineup The

frame is shipped with lockable front doors (locks ordered separately) Preconfigured frames are available

Catalog Number

MX6-TSF6030-7Z4

Dimensions (HxWxD)

2.14 m x 600 mm x 300 mm (7' x 23.6" x 11.8")

O r d e r i n g I n f o r m a t i o n

Description

OMX600 seismic zone 4 rated

fiber distributing cabinet

Please contact ADC Technical Assistance Center to order a preconfigured OMX600 frame

600 mm (23.6") 300 mm(11.8")

300 mm (11.8")

Front View

2.14 m (7')

5/07 • 103742AE

Preterminated Fiber Termination Panels with Pigtails

The OMX600® preterminated pigtail panels are available with either stranded or ribbon preterminated fiber bundles The panels are mounted on the frame and the fiber bundles are then routed directly to the splice section of the OMX600 frame This makes installation of the panels quick and easy, saving valuable installation time Preterminated pigtail panels may be ordered with a ”left“ orientation (mounts on the left side

of the frame) or a ”right“ orientation (mounts on the right side of the frame) ADC recommends the use of 2.0 mm patch cords to maximize the cable management potential of the OMX600

96-Position Panel

Catalog Number MX6-PM 0

Number of Pigtail Assemblies

06 For use with 72-position panel

08 For use with 96-position panel

12 For use with 144-position panel

Panel Capacity

A 72-position

B 96-position

C 144-position (LC only)

Connector/Adapter Type Singlemode

7 SC ultra polish

L SC angled polish

2 FC ultra polish

K LC ultra polish

M LC angled polish

Multimode (62.5/125 μm)

9 SC

A FC

P LC

Pigtail Type

1 12-fiber stranded

3 12-fiber ribbon

4 8-fiber stranded

5 8-fiber ribbon

8 6-fiber stranded

6 6-fiber ribbon

Block Orientation

L Left

R Right

Other configurations are available upon request Please contact ADC Technical Assistance Center

5/07 • 103742AE

Preterminated Fiber Termination Panels with Multifiber Cable – IFC

The OMX600® preterminated panel is available with

indoor rated intrafacility cable (IFC) in ribbon or stranded

configurations All panels are 100% factory tested to guarantee

continuity and reliable connections Preterminated panels make

installation quick and easy, reducing labor costs Panels may be

ordered with a ”left“ orientation (mounts on the left side of

the frame) or a ”right“ orientation (mounts on the right side of

the frame) ADC recommends the use of 2.0 mm patch cords

to maximize the cable management potential of the OMX600

96-Position Termination Panel Catalog Number

MX6-FM 0

Panel Capacity

A 72-position

B 96-position

C 144-position (LC only)

Connector and Adapter Type #1

Singlemode

7 SC ultra polish

L SC angled polish

2 FC ultra polish

K LC ultra polish (144 only)

M LC angled polish (144 only)

Multimode (62.5/125μm)

9 SC

P LC (144 only)

1 Panels using ADC‘s standard cable offering have a shorter lead time than panels using a specific cable

manufacturer ADC only provides GR-409 compliant cable that meets or exceeds our high quality standards.

Connector Type #2

Singlemode

0 No connector/stub end

7 SC ultra polish

L SC angled polish

2 FC ultra polish

K LC ultra polish

M LC angled polish

Multimode (62.5/125 μm)

0 No connector/stub end

9 SC

P LC

Cable Type (IFC Riser) Singlemode

ZB 72-fiber stranded

KA 72-fiber ribbon

ZC 96-fiber stranded

EF 96-fiber ribbon

ZD 144-fiber stranded

FK 144-fiber ribbon

Multimode (62.5/125 μm)

VM 72-fiber stranded

WM 96-fiber stranded

Block Orientation

L Left

R Right

Standard Single-Ended

016 16 m (50')

023 23 m (75')

031 31 m (100')

046 46 m (150')

061 61 m (200')

077 77 m (250')

092 92 m (300')

122 122 m (400')

153 153 m (500')

Non-Standard

Use XXX for length in meters

Other configurations are available upon request Please contact ADC Technical Assistance Center

5/07 • 103742AE

Adapter-Only Fiber Termination Panels

The OMX600® fiber termination panel with adapters only is available with 72-, 96- or 144-positions Panels may be ordered with a ”left“

orientation (mounts on the left side of the frame)

or a ”right“ orientation (mounts on the right side of the frame) ADC recommends the use

of 2.0 mm patch cords to maximize the cable management potential of the OMX600

72-Position Adapter-Only Fiber Termination Panel

Catalog Number MX6-TM 00

Panel Capacity

A 72-position

B 96-position

C 144-position (LC only)

Connector and Adapter Type Singlemode

7 SC ultra polish

L SC angled polish

2 FC ultra polish

K LC ultra polish

M LC angled polish

Multimode (62.5/125 μm)

9 SC

P LC

Other configurations are available upon request Please contact ADC Technical Assistance Center.

Block Orientation

L Left

R Right

5/07 • 103742AE

Splice Panels

The OMX600® splice panel provides mounting

positions and protection for 24 splice trays The

splice panel is the height of two termination panels

(30") The module may be ordered with a ”left“

orientation (mounts on the left side of the frame)

or a ”right“ orientation (mounts on the right side

of the frame) Splice panels must be mounted to

the frame starting in the bottom position

Catalog Number

MX6-24SPNL-R MX6-24SPNL-L

O r d e r i n g I n f o r m a t i o n

Description

OMX600 splice panel accommodates 24 splice trays

Right orientation

Left orientation

Splice Panel

5/07 • 103742AE

Value-Added Module (VAM) Chassis

Value-Added Module (VAM) System

ADC offers an expansive line of monitor, splitter, WDM and CWDM VAM plug-in modules designed

to meet all application needs Please reference the Value-Added Module (VAM) System Catalog

#101663AE for details at www.adc.com or contact ADC Customer Service.

The OMX600® high-density VAM chassis is designed to fit into any open chassis location within new or existing OMX600 fiber distribution frames Each chassis can accommodate a maximum of 18 high-density VAM plug-in modules, 18 bulkhead plates, 18 blank plates or any combination thereof

O r d e r i n g I n f o r m a t i o n

OMX600 high-density VAM chassis, unloaded

- left orientation; accommodates up to 18 single

OMX600 high-density modules

373 mm x 227 mm x 286 mm (14.7" x 8.9" x 11.3")

MX6-HDVAMCHAS-L

OMX600 high-density VAM chassis, unloaded

- right orientation; accommodates up to 18 single

OMX600 high-density modules

373 mm x 227 mm x 286 mm (14.7" x 8.9" x 11.3")

MX6-HDVAMCHAS-R

MX6-HDVAMCHAS-L

(Left Orientation)

MX6-HDVAMCHAS-R

(Right Orientation)

VAM Chassis

(Right Orientation)

5/07 • 103742AE

Interbay Management Panel

The OMX600 interbay management panel provides slack storage between

frames for interconnect or cross-connect jumpers The interbay management

panel is necessary when no jumper storage is provided on the OMX frame itself.

Frame Accessories

Jumper Storage Panel

The OMX600® jumper storage panel provides for jumper storage functionality within

the frame Up to five jumper storage panels can be mounted on one side of an OMX600

frame Jumper storage panels must be mounted to the frame starting in the bottom position

Catalog Number

MX6-ENDGRD

Dimensions (HxD)

2.14 m x 300 mm (84" x 11.8")

O r d e r i n g I n f o r m a t i o n

Description

End guard

End Guard

The OMX600 end guard provides protection for the fibers entering and exiting frames at the ends

of a lineup The end guard attaches directly to the frame, but does not add to the overall frame width

End guards are not required when ordering splice frames

Catalog Number

MX6-JSM00000

O r d e r i n g I n f o r m a t i o n

Description

Jumper storage panel

Dimensions (HxWxL)

368 mm x 127 mm x 248 mm (14.5" x 5" x 9.75")

Frame Installation Kit

Frame installation kits may be used on network frames and are seismic zone 4 rated

Catalog Number

RAC-MX0616

RAC-MX0615

O r d e r i n g I n f o r m a t i o n

Description

Concrete floor frame installation kit, includes:

(2) M8 bolts, 90 mm (3.5")

(4) M8 nuts

(8) flat washers

(4) lock washers

shims and anchor plates

Raised floor frame installation kit, includes:

(4) threaded rods M12 x 1 m (3.28")

(12) heavy nuts, lock and flat washers

(4) nuts with springs, M12

(2) 1.8 m (5.9") unistrut

(1) anchor kit

Catalog Number

MX6-IMP150

Dimensions (HxWxL)

2.14 m x 150 mm x 300 mm (84" x 15.9" x 11.8")

O r d e r i n g I n f o r m a t i o n

Description

Interbay management panel

5/07 • 103742AE

Frame Accessories Splice Frame

The OMX600® splice frame is a high-density splice solution, housing up to 1,440 splices within a 23.6- by 11.8-inch footprint Shipped complete with the necessary cable management, it features slots which secure and protect the round splice trays and can hold up to sixty 12-fiber splice trays on each vertical The frame is shipped with lockable front doors and may be ordered for applications in which the cables enter from above or below

2.14 m (7')

610 mm

Catalog Number

MX6-SPL6030-A-D7Z4 MX6-SPL6030-A-U7Z4 FEC-ACCCLMP01 MX6-SPLIFCCLMP

Dimensions (HxWxD)

2.14 m x 610 mm x 305 mm (7' x 24" x 12")

O r d e r i n g I n f o r m a t i o n

Description Fully configured splice frame

accommodates up to 1440 splices

Cable enters from underfloor Cable enters from top

Splice frame cable clamps for

OSP cable IFC cable

5/07 • 103742AE

Panel Accessories

Splice Tray

The round splice tray used in the OMX600®

simplifies installation and maintenance The

tray stores up to 9.8-feet of slack allowing the

installer to roll the tray away from the frame to

perform splicing

Catalog Number FST-DRS _ _ - _ _

00 FT HS MT

Empty Bare fusion Heat shrink (single fiber fusion) Mechanical (mass fusion)

Splice Type Drawer Capacity

1

For 8-fiber ribbon only

12

16

24

321

Other configurations are available upon request Please contact ADC Technical Assistance Center

Cable Clamp

The OMX600 cable clamp is used to secure the OSP/IFC cable to the base or top of the frame in

a non-splice frame

Catalog Number

OSP-CLPFEC-LG MX6-ACC001

O r d e r i n g I n f o r m a t i o n

Description

OSP/IFC cable clamp for

Top entry cables

Underfloor cable entry