Configuring an Access Server Terminal serverPractical Scenario Một terminal server sẽ cho phép truy cập đến toàn bộ các routers trong rack.. Lab Exercise Trong bài tập này, bạn sẽ cấu hì
Trang 1Configuring an Access Server (Terminal server)
Practical Scenario
Một terminal server sẽ cho phép truy cập đến toàn bộ các routers trong rack
Lab Exercise
Trong bài tập này, bạn sẽ cấu hình một terminal server để reverse-telnet bằng cách này, bạn không cần phải chuyển đổi console giữa các thiết bị
Lab Objectives
Tạo một interface loopback có địa chỉ là 201.201.1.1 Địa chỉ này nhằm mục đích làm 'bàn đạp' cho phép thử reverse telnet
Cấu hình một bảng host table sao cho:
− Hostname r1 performs a reverse Telnet to the first router in your stack
− Hostname r2 performs a reverse Telnet to the second router in your stack, and so on
Thiết bị được dùng cho lab:
- Two Cisco routers and 1x Cisco 2509–2511, or a 2600 series router with an
asynchronous module for the access server
- Octal cables
Sơ đồ đấu nối:
One workstation connected by its COM port to a Cisco 2509–2511, through Cisco black
or light−blue rolled cable is required
Connect the octal cable labeled 1 to an R1 or the first router's console port Repeat this process for every router or switch in lab
Các bước tiến hành lab:
Đề cấu hình reverse-telnet, thực hiện các bước:
Router#show line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY − − − − − 0 1 0/0 −
1 TTY 9600/9600 − − − − − 0 0 0/0 −
Trang 22 TTY 9600/9600 − − − − − 0 1 0/0 −
3 TTY 9600/9600 − − − − − 0 0 0/0 −
4 TTY 9600/9600 − − − − − 0 0 0/0 −
5 TTY 9600/9600 − − − − − 0 0 0/0 −
6 TTY 9600/9600 − − − − − 0 1 0/0 −
* 7 TTY 9600/9600 − − − − − 0 2 0/0 −
8 TTY 9600/9600 − − − − − 0 0 0/0 −
9 TTY 9600/9600 − − − − − 0 0 0/0 −
10 TTY 9600/9600 − − − − − 0 0 0/0 −
11 TTY 9600/9600 − − − − − 0 0 0/0 −
12 TTY 9600/9600 − − − − − 0 0 0/0 −
13 TTY 9600/9600 − − − − − 0 0 0/0 −
14 TTY 9600/9600 − − − − − 0 0 0/0 −
15 TTY 9600/9600 − − − − − 0 0 0/0 −
16 TTY 9600/9600 − − − − − 0 0 0/0 −
17 AUX 9600/9600 − − − − − 0 0 0/0 −
18 VTY − − − − − 0 0 0/0 −
19 VTY − − − − − 0 0 0/0 −
20 VTY − − − − − 0 0 0/0 −
21 VTY − − − − − 0 0 0/0 −
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
22 VTY − − − − − 0 0 0/0 −
Router#
Cấu hình bảng host name:
Router#
Router#conf t
Enter configuration commands, one per line End with CNTL/Z
Router(config)#hostname access−server
access−server(config)#ip host r1 2001 201.201.1.1
access−server(config)#ip host r2 2002 201.201.1.1
access−server(config)#ip host r3 2002 201.201.1.1
access−server(config)#ip host r3 2003 201.201.1.1
access−server(config)#ip host r4 2004 201.201.1.1
access−server(config)#ip host r5 2005 201.201.1.1
access−server(config)#interface loopback 0
access−server(config−if)#ip address 201.201.1.1 255.255.255.0
access−server(config−if)#exit
access−server(config)#
Example 1−51 Configuring the Absolute Lines for Support of Reverse Telnet, and Disabling the Exec
Trang 3access−server(config)#line 1 5
access−server(config−line)#transport input all
access−server(config−line)#no exec
access−server(config−line)#^Z
access−server#
Để kiểm tra cấu hình, chỉ cần nhập vào r1 và một session sẽ kết nối đến r1 Dùng lệnh clear line x nếu session bị từ chối
Example 1−52 Complete Listing of a Router Configured as an Access Server
access−server#wr t
Building configuration
Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password−encryption
!
hostname access−server
!
ip subnet−zero
ip host r1 2001 201.201.1.1
ip host r2 2002 201.201.1.1
ip host r3 2003 201.201.1.1
ip host r4 2004 201.201.1.1
ip host r5 2005 201.201.1.1
!
interface Loopback0
ip address 201.201.1.1 255.255.255.0
no ip directed−broadcast
!
interface Ethernet0
no ip address
no ip directed−broadcast
shutdown
!
interface Serial0
no ip address
no ip directed−broadcast
no ip mroute−cache
shutdown
!
interface Serial1
no ip address
no ip directed−broadcast
Trang 4!
ip classless
!
line con 0
transport input none line 1 5
no exec
transport input all line 6 16
line aux 0
line vty 0 4
!
end
access−server