Bsi bs en 27436 1992 (1999)

www bzfxw com BRITISH STANDARD BS EN 27436 1992 ISO 7436 1983 Slotted set screws with cup point The European Standard EN 27436 1992 has the status of a British Standard UDC 621 882 219 4 092 6 BS EN 2[.]

BRITISH STANDARD BS EN

27436:1992 ISO 7436:1983

Slotted set screws with

cup point

The European Standard EN 27436:1992 has the status of a

British Standard

UDC 621.882.219.4.092.6

This British Standard, having

been prepared under the

direction of the General

Mechanical Engineering

Standards Policy Committee,

was published under the

authority of the Standards

Board and comes into effect on

15 October 1992

© BSI 11-1999

The following BSI references

relate to the work on this

standard:

Committee reference GME/9

Draft for comment 72/70266 DC

ISBN 0 580 21293 9

Cooperating organizations

The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries:

Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y

France Association française de normalisation Germany Deutsches Institut für Normung c.V

Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland

Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portuguès da Qualidade Spain Asociación Española de Normalización y Certificación Sweden Standardiseringskommissionen i Sverige

Switzerland Association suisse de normalisation United Kingdom British Standards Institution

Amendments issued since publication

Amd No Date Comments

BS EN 27436:1992

Contents

Page Cooperating organizations Inside front cover

National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover

ii © BSI 11-1999

National foreword

This British Standard has been prepared under the direction of the General Mechanical Engineering Standards Policy Committee and is the English

language version of EN 27436:1992 Slotted set screws with cup point, published

by the European Committee for Standardization (CEN) It is identical with ISO 7436:1983, published by the International Organization for Standardization (ISO) EN 27436:1992 was produced as a result of international discussions in which the United Kingdom took an active part

BS 4219-4:1985 which was identical to ISO 7436:1983 is now superseded by this British Standard and has been withdrawn in accordance with the

CEN/CENELEC Internal Regulations

A British Standard does not purport to include all the necessary provisions of a contract Users of British Standards are responsible for their correct application

Compliance with a British Standard does not of itself confer immunity from legal obligations.

Summary of pages

This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover

This standard has been updated (see copyright date) and may have had amendments incorporated This will be indicated in the amendment table on the inside front cover

EUROPEAN STANDARD

NORME EUROPÉENNE

EUROPÄISCHE NORM

EN 27436

July 1992

UDC 621.882.219.71.092.6

Descriptors: Fasteners, screws, set screws, specifications, dimensions, designation

English version Slotted set screws with cup point

(ISO 7436:1983)

Vis sans tête, fendues, à bout cuvette

This European Standard was approved by CEN on 1992-07-17 CEN members

are bound to comply with the CEN/CENELEC Internal Regulations which

stipulate the conditions for giving this European Standard the status of a

national standard without any alteration

Up-to-date lists and bibliographical references concerning such national

standards may be obtained on application to the Central Secretariat or to any

CEN member

This European Standard exists in three official versions (English, French,

German) A version in any other language made by translation under the

responsibility of a CEN member into its own language and notified to the

Central Secretariat has the same status as the official versions

CEN members are the national standards bodies of Austria, Belgium,

Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,

Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and

United Kingdom

CEN

European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung

Central Secretariat: rue de Stassart 36, B-1050 Brussels

© 1992 Copyright reserved to CEN members

Ref No EN 27436:1992 E

© BSI 11-1999 2

Foreword

In 1992, CEN Technical Committee CEN/TC 185,

Threaded and non threaded mechanical fasteners

and accessories, the secretariat of which is held by

DIN decided to submit the International Standard

ISO 7436:1983 “Slotted set screws with cup point” to

the formal vote procedure The result was positive

In the countries bound to implement this European

Standard a national standard identical to this

European Standard shall be published at the latest

by 1993-01-31 and conflicting national standards

shall be withdrawn at the latest by 1993-01-31

According to the CEN/CENELEC Common Rules

the following countries are bound to implement this

European Standard: Austria, Belgium, Denmark,

Finland, France, Germany, Greece, Iceland,

Ireland, Italy, Luxembourg, Netherlands, Norway,

Spain, Portugal, Sweden, Switzerland and

United Kingdom

Contents

Page

1 Scope and field of application 3

4 Specifications and reference International Standards 5

EN 27436:1992

1 Scope and field of application

This International Standard specifies the characteristics of slotted set screws with cup point and thread sizes from M 1,6 to M 12 inclusive and product grade A

If other specifications are required, it is recommended that they should be selected from existing

International Standards, for example ISO 261, ISO 888, ISO 898, ISO 965, ISO 3506, ISO 4759-1

2 References

ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions

ISO 261, ISO general purpose metric screw threads — General plan

ISO 888, Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts

ISO 898, Mechanical properties of fasteners

ISO 965, ISO general purpose metric screw threads — Tolerances

ISO 3269, Fasteners — Acceptance inspection1)

ISO 3506, Corrosion-resistant stainless steel fasteners — Specifications

ISO 4042, Threaded components — Electroplated coatings components1)

ISO 4753, Fasteners — Ends of parts with external metric ISO thread

ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws and nuts with thread diameters W 1,6

and u 150 mm and product grades A, B and C

1) At present at the stage of draft.

3 Dimensions

1) Sizes in brackets should be avoided if possible.

2) P = pitch of the thread.

3) Min and max values according to ISO 4759-1, but rounded to one decimal place.

EN 27436:1992

4 Specifications and reference International Standards

5 Designation

Example for the designation of a slotted set screw with cup point, thread size d = M5, nominal length

l = 12 mm and property class 14H:

Set screw ISO 7436 – M5 × 12 – 14H

Material Steel Stainless steel Non-ferrous

metal

International Standards ISO 261, ISO 965

Mechanical properties Property class 14H, 22H A1 – 50 a

International Standards ISO 898-5 ISO 3506

International Standard ISO 4759-1

Plain

Finish

Requirements for electroplating are covered in ISO 4042

If different electroplating requirements are desired

or if requirements are needed for other finishes, they should be negotiated between supplier and customer

Acceptability The acceptance procedure is covered in ISO 3269

a Will be covered in a future International Standard.

6 blank

BS EN 27436:1992

© BSI 11-1999

National annex NA (informative)

Committees responsible

The United Kingdom participation in the preparation of this European Standard was entrusted by the

General Mechanical Engineering Standards Policy Committee (GME/-) to Technical Committee GME/9,

upon which the following bodies were represented:

BEAMA Ltd

British Constructional Steelwork Association Ltd

British Industrial Fasteners Federation

British Railways Board

British Steel Industry

British Steel Industry (Wire Section)

Gauge and Tool Makers’ Association

Ministry of Defence

Society of Motor Manufacturers and Traders Ltd

Washer Manufacturers’ Association of Great Britain

The following bodies also participated in the preparation of the standard, through subcommittees and

panels:

British Furniture Manufacturers’ Federation

British Independent Steel Producers’ Association

National Association of Fastener Stockholders

National annex NB (informative)

Cross-references

Publication referred to Corresponding British Standard

ISO 225:1983 BS EN 20225:1992 Fasteners Bolts, screws, studs and nuts Symbols and

designations of dimensions

ISO 261:1973 BS 3643 ISO metric screw threads

Part 1:1981 Principles and basic data

ISO 888:1976 BS 7345:1990 Specification for nominal lengths of bolts, screws and studs and

thread lengths for general purpose bolts

ISO 3506:1979 BS 6105:1981 Specification for corrosion-resistant stainless steel fasteners

ISO 4753:1983 BS 6567:1985 Specification for ends of fasteners with external metric ISO thread

ISO 4759-1:1978 BS 6322 Tolerances for fasteners

Part 1:1982 Specification for tolerances of bolts, screws and nuts with thread

diameters U 1.6 mm and k 150 mm and product grades A, B and C

BSI

389 Chiswick High Road

London

W4 4AL

BSI is the independent national body responsible for preparing British Standards It presents the UK view on standards in Europe and at the international level It is incorporated by Royal Charter

Revisions

British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions

It is the constant aim of BSI to improve the quality of our products and services

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover

Tel: 020 8996 9000 Fax: 020 8996 7400

BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards

Buying standards

Orders for all BSI, international and foreign standards publications should be addressed to Customer Services Tel: 020 8996 9001 Fax: 020 8996 7001

In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested

Information on standards

BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service Various BSI electronic information services are also available which give details on all its products and services Contact the Information Centre

Tel: 020 8996 7111 Fax: 020 8996 7048

Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards For details

of these and other benefits contact Membership Administration

Tel: 020 8996 7002 Fax: 020 8996 7001

Copyright

Copyright subsists in all BSI publications BSI also holds the copyright, in the

UK, of the publications of the international standardization bodies Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI

This does not preclude the free use, in the course of implementing the standard,

of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained

If permission is granted, the terms may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager

Tel: 020 8996 7070