Bsi bs au 215 2 1987 (2000) iso 7804 1985

BRITISH STANDARD AUTOMOBILE SERIES BS AU 215 2 1987 ISO 7804 1985 Power take offs (PTOs) — Part 2 Specification for dimensions of side openings for commercial road vehicles [ISO title Commercial road[.]

ISO 7804:1985

[ISO title: Com m ercial road vehicles— Side opening s for truck

power take-ofs]

U C[ 62 1 4.2+6 9.1 4.4]6 9.1 3-4 4

This Bri shStan ard, ha ing

b en pre ared u der the

directonof the Automo ile

Stan ards Commi e ,was

published u der the authoriy

ofthe Bo rd of BSI an comes

into fect on

3 J n ary1 8

© BSI0 -2 0

The folowing BSI references

relate to the work on this

stan ard:

Commi e reference AUE/13

Draft for comment8 /80 3 DC

ISBN 0 5 0 1 6 9 3

The prep ration of this BritishStand rd was entrusted b the Automobi e

Stand rd s Commit e ( AUE/ -) to Tech ical Commit e AUE/13, upon which

the folowing bodies were represented:

Dep rtment of Transport ( Hig hway s)

Freig ht Transport Association

Institute of Roa Transport Eng ine r ( Incorporated)

Lond on Reg ional Transport

Ministry of Defence

National Bus Comp ny

Roa Haulag e Association Ltd

Society of Motor Man facturer and Tra er Limited

Am endm ents is ued sinc publ cation

Amd No Date of is ue Comments

Pag e

Fig ure 1 — Ty pe R reg ular d uty ty pe6bolts M10—Ty pe R1 2

Fig ure 2 — Ty pe R reg ular d uty ty pe6bolts M10—Ty pe R2

Fig ure 3 — Ty pe H ( H1 an H2) heav y d uty ty pe8bolts M1 4

© BSI 0 -2 0

This Part of BS AU2 5 has be n prep red u d er the d irection of the Automobie

Stand ards Commit e and is id entical with ISO7 0 :19 5 “Commer cia l r oa d

vehicle — Sid e openings f r tr uck power ta ke-o fs”, publshed b the

International Org anization for Stand rdization ( ISO)

BS AU2 5-1 specifies dimensions for the clearance env elope for PTOs

Term inolog y and conventions The text of the International Stand rd has

be n a prov ed as suita le for publcation as a BritishStand rd without

d ev iation Some terminolog y and certain conv entions are not identical with those

used in BritishStand rds; at ention is d rawn especialy to the fol owing

The comma has be n used as a decimal marker In BritishStand ards it is cur ent

practice to use a ful point on the b selne as the decimal marker

W herev er the words “ nternational Stand rd” or “ ISO7 0 ” a pear, refer ing to

this stand ard, they should be read as “ BritishStand ard” and “ BS AU2 5-2”

respectiv ely

A British Stand ard d oes not purport to includ e al the neces ary prov isions of a

contract User of British Stand rd s are responsible for their cor ect a plcation

Com pl anc with a British Standard does not ofitself confer im m unity

f om leg al o l g ations

Sum mary of pag es

This document comprises a f ont cov er, an insid e font cov er, p g esi andi ,

p g es1 to4 an a b ck cov er

This stand rd has be n up ated ( se copy rig ht d ate) an ma hav e ha

amendments incorporated This wi l be indicated in the amendment ta le on the

inside f ont cov er

1 Scope and field ofappl cation

This International Stand rd lay s d own the

dimensions of sid e opening s for truck power

take-ofs These specifications are a plca le for al

g eneral instal ations of power take-ofs on the

transmis ion g ear box of trucks an tractor where

the siz of the transmis ion permits

2 Definition

g ear depth

distance f om transmis ion face to pitch l ne of

power take-of driv e g ear

3 Specifications

3.1 Types

This International Stand rd d efines two ty pes of

side opening :

— Ty pe R: reg ular duty ty pe,6 bolts M10

— Ty pe H: heav y duty ty pe, 8 bolts M1

Both ty pes are specified with two alternativ e g ear

depths and subd iv ided ac ording ly

3.2 Ty e R

Ty pe R shal hav e one of the folowing g ear depths:

— Ty pe R1:20±10mm

— Ty pe R2:7 ±10mm

Ty pe R1 shal comply with the req uirements of

Fig ure 1

Ty pe R2 shal comply with the a ditional

requirements of Fig ure 2

3.3 Ty e H

Ty pe H shal hav e one of the fol owing g ear d epths:

— Ty e H1: 14±10mm

— Ty e H2: 6 ±10mm

Ty pes H1 and H2 shal comply with the

requirements of Fig ure 3

4 Desig na tion

Ex mple for the desig nation of a6bolt M10 sid e

opening ( ty pe R) with g ear d epth20±10mm

( cod e1):

PTO o ening ISO7 0 -R1

© BSI 0 -2 0

N T 1 Ge r data an b cklash are sp cified b g earb x man facturer

N T 2 P O driv g ear ma b located eiher side of the v rtcal centre-ine

Fig ure 1 — Ty e R reg ular duty ty e6bolts M10— Ty e R1

NOT For al other dimensions,se Fig ure 1.

Fig ure 2 — Ty e R reg ular duty ty e6 bolts M10— Ty e R2 (wide c ntre o ening )

© BSI 0 -2 0

N T 1 Ge r data an b cklash are sp cified b g earb x man facturer

N T 2 P O driv g ear ma b located eiher side of the v rtcal centre-ine

Fig ure 3 — Ty e H (H1 and H2) hea y duty ty e8 bolts M12

b

ISO 7804:1985

BSI

3 9 Chiswick Hig h Roa

London

W 4 4AL

BSI is the independent national bod y responsible for prep ring

BritishStand ard s It presents the UK v iew on stand ard s in Europe an at the

international lev el It is incorporated b Roy al Charter

Revisions

BritishStand ards are up ated b amendment or rev ision User of

BritishStand ard s should make sure that they pos es the latest amendments or

editions

It is the constant aim of BSI to improv e the qual ty of our products and serv ices

W e would be g rateful if any one find ing an inac uracy or ambig uity whi e using

this BritishStand rd would inform the Sec etary of the technical commit e

responsible, the identity of which can be fou d on the inside f ont cov er

Tel:0208 9 9 0 Fa :0208 9 7 0

BSI ofer member an indiv id ual up ating serv ice caled PLUS which ensures

that subs riber automaticaly receiv e the latest editions of stand rds

Buying standards

Order for al BSI, international an foreig n stand ard s publcations should be

a d res ed to Customer Serv ices Tel:0208 9 9 01 Fa :0208 9 7 01

In response to ord er for international stand rd s, it is BSI pol cy to sup ly the

BSI implementation of those that hav e be n publ shed as BritishStand rds,

unles otherwise requested

Inform ation on standards

BSI prov id es a wide rang e of information on national, European and

international stand rds throug h its Library and its Tech ical Help to Ex orter

Serv ice Various BSI electronic information serv ices are also av aia le which g iv e

d etais on al its prod ucts an serv ices Contact the Information Centre

Tel:0208 9 71 1 Fa :0208 9 7 4

Subs ribing member of BSI are kept up to d te with stand rd s dev elopments

and receiv e substantial d is ou ts on the pur hase price of stand rds For d etai s

of these and other benefits contact Member hip Ad ministration

Tel:0208 9 7 02 Fa :0208 9 7 01

Co yrig ht

Copy rig ht subsists in al BSI publcations BSI also holds the copy rig ht, in the

UK, of the publcations of the international stand ardization bod ies Except as

permit ed u der the Cop rig ht, Desig ns and Patents Act 19 8 no extract ma be

reproduced , stored in a retriev al sy stem or transmit ed in any form or b any

means – electronic, photocopy ing , recording or otherwise – without prior writ en

permis ion fom BSI

This do s not preclude the fe use, in the cour e of implementing the stand ard,

of neces ary detai s such as sy mbols, and siz , ty pe or g ra e d esig nations I these

d etais are to be used for any other purpose than implementation then the prior

writ en permis ion of BSI must be obtained

I permis ion is g ranted, the terms ma includ e roy alty p y ments or a lcensing

ag re ment Detais and a v ice can be obtained f om the Copy rig ht Manag er

Tel:0208 9 7 7