Quản trị mạng CCNP.Sem5.MLS CEF

Quản trị mạng

Nguyen Khac Quyet - Take Exam

Exam questions

Time remaining: 00: 06: 30

1 What does a Catalyst 8500 use for Layer 3 switching?

MLS

MSFC

NFFC

CEF

2 What can you use with the Catalyst 5000 to do multiprotocol routing?

SRM

RSM

SAGE

SAINT

3 What do you do to configure MLS-SE to participate in MLS with an in-house RSM?

MLS is enabled by default

Enter the “set mls enable” command in privileged mode

Enter the “set mls enable” and “set mls include rsm ip address” Commands in privileged mode

Enter the “set mls enable” and “set mls vtp-domain vtp domain name” commands in privileged mode

Enter the “set mls enable” and “set mls agingtime number-of-seconds” commands in privileged mode

4 What are the three different flow masks that are supported by the MLS-SE?

Destination-IP

Source-Destination-IP

IP-Flow

IN-Flow

5 What command would you use to see the flow mask type that is currently enabled on the MLS-SE?

show flow

show flow-mask

show mls

show mask

6 What is true regarding Cisco’s NetFlow technology? Choose three (Chi con 2 y thoi)

Allows you to gather detailed information on your traffic flows

Can only be used with extended access lists

Allows for the deployment of access lists without any performance penalty when used in tandem with Multilayer Switching Requires a Layer 2 device to provide Layer 3 services

7 A Supervisor Engine is not required for the 6x00 series of switches

True

False

8 The required components of Cisco Systems MLS implementation are: (Choose three)

The MLS-SE

The MLS-RP

The MLS-PR

The MLSP

9 Read and answer the question

A

B

C

D

10 If you had two Telnet sessions occurring between two PC’s, why would these sessions be treated as two different traffic flows within MLS cache even though the Layer 3 addressing is the same?

The source port numbers would be different

The MLS-RP would change the IP addresses to MAC addresses

The MLS-PR converts the IP addresses to different traffic flows

The default gateway would age out all entries to make room for new entries

11 What are three advantages of Multilayer switching?

Combines functionality of Layer 2, Layer 3, and Layer 4 switching

High-speed functionality

Switching is software-based

Low latency

12 What is true regarding MLS cache?

Bidirectional flow

Knows data flows

Two-way flow

Unidirectional flow

13 Cisco defines a traffic flow as a set of packets between a specific source and destination where the protocol and the port numbers are different

True

False

14 What command would you use to add an interface to a new VTP domain on an RP (Route Processor)?

mls rp

mls vtp-domain

mls rp vtp-domain

mls ip rp

15 Layer 4 switching has better performance than Layer 3 switching

True

False

16 What daughter card for the 6x00 series of switches is similar to the RSFC that is used in the 5000 series of switches?

MSFC

RSM

NFFC

MSM

17 What are the three basic types of packets?

Unicasts

Local Broadcasts

Multicasts

Remote Broadcasts

18 What is the purpose of defining an MLS Management Interface?

To disable MLS

To allow MLS to function

To stop the flow of MLSP packets

To prevent overruns

19 Read and answer the question

A

B

C

D

E

F

20 What are two ways that Cisco routers can control traffic based on Layer 4 information?

Extended access lists

Standard access lists

Layer 4 accounting using Fast switching

Layer 4 accounting using NetFlow switching

21 For Layer 3 switching to work, the MLS-SE must see the traffic flow:

in only one direction from the MLS-SE

in only one direction from the MLS-RP

in both directions from the MLS-RP

in both directions from the MLS-SE

22 What command would you use to allow input access lists?

mls rp ip input-acl

mls ip rp input-acl

mls ip input-acl

mls rp input-acl

23 The first module in the Catalyst 5000 switches:

should contain at least 12 Ethernet ports

is not required to be utilized

contains an interface module

contains the console port in the Supervisor Engine

24 What is true regarding the RSFC (Route Switch Feature Card)? Choose two

It is a full function IOS router installed as an integrated daughter card

It is used on the Catalyst 5000 series Supervisor IIG and Supervisor IIIG Engines Can only be used on the Supervisor II Engine

Can only be used on the Supervisor III Engine

Showing page 1 of 1 : 1 Go!

© 2004 HanoiCTT All rights reserved