Tài liệu CCIE Practice Scenario Labs doc

At the end of each exercise, verify connectivity between all ports: 4.. Configure two loopbacks on R6 using subnets that will contain at most 14 host ip addresses.. Filter on R2 such tha

CCIE Practice Scenario Labs Introduction

This document is designed to be a companion to Volume 1,2,3 and 4 The CCIE certification is a written test and a lab test This document will help the student further build upon their technical skills and configuration skills The document contains practice CCIE scenario labs

Background

These scenarios have been compiled from various sources including current partner CCIEs

These are not the only scenarios you will be tested with on the CCIE lab exam They are designed to give you a flavor for the lab exam Students are encouraged to use these scenarios to assist them in devising other scenarios with different physical topologies using multiprotocol scenarios

REMEMBER: YOU CAN BE TESTED ON ANY AND ALL TECHNOLGIES ON THE CCIE LAB EXAM

Prerequisites

The student must also have taken and past the CCIE written test

CCIE Practice Lab Scenario 1

NBMA Network

(Frame Relay)

Ring 1

R6

R5

R1

R2

Ring 3

R3 Ring 2

110 101

Lab 1 Connect Terminal Server (1 hour)

1 Setup routers as shown in the diagram above:

2 Configure a ip host list for a reverse telnet session into each router

Lab 2 IP (6 hours)

1 Configure the network using network 130.10.x.x

2 Use an 8 bit subnet mask unless otherwise specified

3 At the end of each exercise, verify connectivity between all ports:

4 All ip routes appearing in all routers

5 Ping from any interface to any other interface

Lab 2a

1 Connect R6, R1, and R5 over Frame Relay Use single subnet over the

frame cloud

2 Configure OSPF with the cloud in area 0 Configure R2, R3 and R1-R2 serial

to be in area 1

3 Configure two loopbacks on R6 using subnets that will contain at most 14

host ip addresses Configure two loopbacks on R5 using subnets that will

contain at most 62 hosts Summarize the two loopback interfaces on R6 and

R5 such that R1 only sees one route from each

Lab 2b

1 Remove OSPF configurations from R2, R3 and the serial connection between

R1 and R2 Configure EIGRP on R2, R3 and on the serial connection

between R1 and R2 Redistribute OSPF and EIGRP on R1

2 Repeat step 1 using IGRP instead of EIGRP

Lab 2c

1 Filter such that R3 can ping the loopbacks on R5 but not the ethernet The

route for the ethernet should still be visible

2 Filter on R2 such that R6, R5, and R1 only see the routes from the token-ring

interface on R3

3 Remove the filters from R2

Lab 3 Appletalk (1 hour)

At the end of each exercise, verify connectivity between all ports:

1 All Apple routes/zones appearing in all routers

2 Apple ping from any interface to any other interface

Lab 3a

1 Configure all ports (except loopbacks) for appletalk Define a zone on each

interface Define an interface on R3 as Appletalk phase I

2 Configure EIGRP for R1, R2, and R3

3 Configure RTMP/ZIP for the NBMA network

Lab 3b

1 Filter on R2 such that R3 only sees routes and zones from R6

Lab 3c

1 Remove Appletalk from the serial network between R1 and R2 All zones and

routes should still be seen by all routers running Appletalk

Lab 4 DECnet (30 minutes)

At the end of each exercise, verify connectivity between all ports

1 Appropriate DEC areas/nodes appearing in all routes

2 DEC ping from any router to any other router

Lab 4a

1 Enable DECnet routing on all routers Configure R2 and R3 in a separate

DECnet area from the rest of the routers

Lab 5 IPX (1 hour)

At the end of each exercise, verify connectivity between all ports

1 Appropriate IPX routes/SAP’s appearing in all routers

2 IPX ping from any interface to any other interface

Lab 5a

1 Configure all ports (including loopbacks) for IPX

2 ConfigureRIP/SAP on R2, R3, and the serial network between R1 and R2

3 Configure only EIGRP on R6, R5, and R1’s NBMA network interface

4 Redistribute on R1

Lab 5b

1 Configure two static SAPs on R3 Filter on R2 such that R6, R5, and R1 see

only one of theSAPs

2 Disable IPX across the NBMA network All routes should still be seen by all

routers running IPX

3 Change the frequency of RIP updates across the token-ring connection

between R2 and R3 to once every 2 minutes

Lab 6 Dial-on-demand routing (2 hours)

At the end of each exercise, verify connectivity between all ports:

1 Ping all interfaces using applicable protocols

Lab 6a

1 Configure an ISDN connection between R1 and R2

2 Disconnect the serial link between R1 and R2

3 Configure dial-on-demand routing for IP and IPX between R1 and R2 No

broadcast packets should initiate the dialing

4 Reconnect the serial link between R1 and R2 and shut down the ISDN

interfaces

Lab 7 DLSW (1 hour)

1 Configure DLSW between Ring1 and Ring 3

2 Add R1’s ethernet into the DLSW network Make sure there is connectivity

between all lan interfaces

Lab 7a

1 Configure a filter that blocks Netbios packets with destination name “Finance”

from leaving Ring 3

2 Set up a filter that would permit only SNA traffic between the token-rings

Lab 8 BGP (1 hour)

1 Remove the routing protocol from the serial link between R1 and R2 Create

a BGP autonomous network between these routers For the AS containing R2

and R3, configure the network using network 140.20.0.0 Redistribute and

aggregate all routes