A decrease of anisotropy field and an increase of GMI with increasing annealing temperature up to 540 8C were observed and ascribed to the increase of the magnetic permeability and the d
Trang 1Effect of annealing on the microstructure and magnetic properties
of Fe-based nanocomposite materials
Manh-Huong Phana,*, Hua-Xin Penga, Michael R Wisnoma, Seong-Cho Yub, Nguyen Chauc
a
Department of Aerospace Engineering, Bristol University, Queen’s Building, University Walk, Bristol BS8 1TR, UK
b
Department of Physics, Chungbuk National University, Cheongju 361-763, South Korea
c
Center for Materials Science, National University of Hanoi, 334 Nguyen Trai, Hanoi, Vietnam Received 4 October 2004; revised 8 January 2005; accepted 11 January 2005
Abstract
The influence of annealing on microstructure, magnetic properties including the giant magnetoimpedance (GMI) effect of a Fe-based nanocomposite has been investigated The nanocomposite structure composed of ultra-fine Fe(Si) grains embedded in an amorphous matrix was attained by annealing the Fe-based amorphous alloy prepared by rapid quenching method The GMI profiles were measured for samples annealed at different temperatures ranging from 350 to 650 8C in vacuum and for 30 min It is found that the mean grain size of the a-Fe(Si) crystallites in the order of 12 nm remains almost unchanged until the annealing temperature reached 540 8C A decrease of anisotropy field and an increase of GMI with increasing annealing temperature up to 540 8C were observed and ascribed to the increase of the magnetic permeability and the decrease of the coercivity, whereas the opposite tendency was found for the sample annealed above 600 8C which is likely due to the microstructural change caused by high-temperature annealing This indicates that variation in the magnetic characteristic of the amorphous phase upon annealing changed the intergrain exchange coupling This altered both the magnetic softness and the effective anisotropy and consequently modified the GMI features The study of the temperature dependence of the GMI effect provides further understanding of the magnetic exchange between these crystallized grains through the amorphous boundaries in Fe-based nanocrystalline materials
q2005 Elsevier Ltd All rights reserved
Keywords: B Anisotropy; Magnetoimpedance
1 Introduction
Recent advances in magnetic sensing applications,
especially in the high-density magnetic recording
technol-ogy, has benefited from the discovery of new magnetic
materials with amorphous structure [1–3] In contrast to
crystalline magnetic materials where the periodicity of
constituent atoms plays an essential part, in an amorphous
substance, atoms are distributed randomly, taking a
topologically disordered structure The absence of crystal
structure (i.e the presence of a short range order and the
absence of a long range order) leads to superior properties
(e.g mechanical, chemical, electrical, and magnetic proper-ties) observed in these materials
It is known that the absence of magnetocrystalline anisotropy and grain boundaries in an amorphous magnetic material results in excellent soft magnetic properties (e.g high magnetic permeability and saturation induction), high electrical resistivity leading to small eddy current losses, high hardness and stiffness etc Importantly, a variety of properties can be achieved by the applications of external parameters (e.g magnetic field, pressure, temperature, etc.) and/or by controlling the fabrication processes [1] The combined magnetic, electrical, mechanical and chemical properties are making an amorphous magnetic material the most promising candidate material for many engineering applications[3]
In view of the existing materials, the discovery of Finemet-type nanocomposite magnetic materials with a composition of Fe73.5Si13.5B9Cu1Nb3 provided some insights into the science and technology of soft magnetic
www.elsevier.com/locate/compositesa
1359-835X/$ - see front matter q 2005 Elsevier Ltd All rights reserved.
doi:10.1016/j.compositesa.2005.01.033
* Corresponding author Tel.: C44 783 823 2277; fax: C44 117 927
2771.
E-mail address: m.h.phan@bristol.ac.uk (M.-H Phan).
Trang 2materials[4–8] This kind of materials, routinely obtained
by an appropriate heat treatment of an amorphous precursor,
exhibits excellent magnetic properties due to its unique
microstructure, namely, ultrafine nanocrystalline a-Fe(Si)
grains embedded in an amorphous matrix [6] This is
directly depending on the magnetic exchange coupling
between the grains through the amorphous boundaries
[9,10] However, the underlying physical mechanism of the
magnetic exchange coupling in a nanocrystalline magnetic
material is not well understood
Fortunately, a number of recent studies on the giant
magnetoimpedance (GMI) effect in Fe-based amorphous
soft magnetic alloys subjected to heat treatment showed
some insights into the nature of the magnetic exchange
coupling between these grains through the amorphous
boundaries in Fe-based nanocrystalline materials [7,8,11–
13] Because of the fact that the two-phase Fe-based
nanocomposite material has two distinct Curie
tempera-tures, one for the nanocrystalline grains and the other
belonging to the amorphous phase, the roles of the two
magnetic phases in the intergrain magnetic coupling can be
taken apart in a sufficiently high temperature region
In this context, the study of the temperature dependence
of the magnetic properties and the GMI effect in such a
Fe-based nanocomposite material composed of a
nanocrystal-line phase in an amorphous matrix can be of significant
importance in gaining more rudimentary insights into the
nature of the magnetic coupling in the material This paper
reports the effect of annealing on the structural and magnetic
properties and the GMI effect in a Fe73.5Si15.5Nb3Cu1B7
amorphous alloy
2 Experiment
Fe73.5Si15.5Nb3Cu1B7ribbons with a width of 4 mm and
a thickness of 20 mm were prepared by rapid quenching
method The nanocomposite materials composed of a
nanocrystalline phase in an amorphous matrix were
obtained by annealing these as-quenched amorphous
ribbons at different temperatures ranging between 350 and
650 8C for 30 min in vacuum The structures of the
as-quenched amorphous ribbons and the annealed ones were
examined by X-ray diffraction (XRD) Differential scanning
calorimeter (DSC) measurements on as-cast and annealed
ribbons were conducted with increasing temperature at a
rate of 20 8C/min in Ar atmosphere Accordingly, the
crystallization processes can be monitored by DSC
Transmission electron microscopy (TEM) images of the
nanocrystallized ribbons have been obtained for samples
thinned by using a Philips C30 ion etching device The M–H
hysteresis loops were measured using a vibrating sample
magnetometer (VSM) Magneto-impedance (MI)
measure-ments were carried out along the ribbon axis with the
longitudinal applied magnetic field The samples with a
length of about 15 mm were used for all MI measurements
Details on a MI measurements system can be found elsewhere[14]
3 Results and discussion 3.1 Microstructural analyses
Fig 1 shows the XRD pattern of the Fe-based as-quenched amorphous ribbon It is clear that the pattern exhibited only one broad peak around 2qZ458, which is often known as a diffuse halo, indicating that the sample prepared is amorphous No indication of presence of crystallites was observed by TEM This reflects the absence
of crystal structure, i.e the absence of a long range order
To find out a proper annealing regime for as-quenched amorphous ribbon samples, we carried out DSC measure-ments Typical DSC curves for the as-cast and 540 8C-annealed ribbons are shown inFig 2 It is easy to see clearly fromFig 2that for the as-cast sample the curve has a typical behavior with the two mainly exothermic peaks; the first exothermic peak (first peak at w550 8C) is attributed to the primary crystallization of the nanocrystalline phase (e.g the a-Fe(Si) soft magnetic phase) while the second one is attributed either to the further crystallization of the remaining amorphous phase, or to phase transformation of existing metastable phases, such as Fe3B, following the primary crystallization In the case of the annealed sample, the crystallization peaks shifted to a higher temperature due
to a significant contribution of nucleation It was also found that the first peak disappeared for the sample annealed at
650 8C for 30 min, indicating a full crystallization state Based on the DSC results, as-cast amorphous alloys were annealed at different temperatures ranging between 350 and
650 8C for 30 min in vacuum to achieve the nanocrystalline materials with a-Fe(Si) phase
Furthermore, it is known that the crystallization fraction determines magnetostriction of the ribbon while the grain
Fig 1 The X-ray diffraction pattern of the Fe 73.5 Si 15.5 Nb 3 Cu 1 B 7 as-cast amorphous alloy.
Trang 3size determines the magnitude of the effective magnetic
anisotropy Both magnetostriction and effective magnetic
anisotropy play a decisive role in the soft magnetic
properties of nanocrystalline magnetic materials It is
therefore necessary to evaluate the crystallization fraction
of the sample after annealing Recently, Leu and Chin[15]
have first proposed the method that allows one to evaluate
the crystallization fraction (cf) from the DSC diagram,
which is expressed by:
cfZDHaKDHt
where DHaand DHt are the crystallization enthalpy of the
as-cast amorphous ribbon and the ribbon annealed for a time
t, respectively An example is also shown inFig 2, where
the crystallization fraction of the sample annealed at 540 8C
for 30 min, corresponding to the a-Fe(Si) phase at the first
peak, reaches a value of 82% We have found that the
amorphous sample became fully crystallized (cfZ100%)
when annealed above 650 8C It should, however, be noted
that the soft magnetic property may be degraded by
excessive crystallization Because, for annealing over
650 8C, the BCC crystallites will grow, and large crystallites
lead to the decoupling of magnetic exchange, and
consequently the good soft magnetic properties are lost
To further scrutinize this feature, the structure of the
amorphous samples after annealing was examined by XRD
and TEM [see Fig 3, for example] After the thermal
treatments the XRD peaks of a-Fe(Si) are seen to emerge
from the amorphous halos The relative intensity of the
various peaks indicates that there is no preferred orientation
in the crystallized phase Furthermore, the mean grain size
(t) of a-Fe(Si) was determined according to the Scherrer
expression[16]:
t Z 0:96l
where l is the X-ray wavelength (lZ1.54056 A˚ ), q is the diffraction angle, and B is the full width at half maximum (FWHM)
In Fig 4 we display the annealing-temperature depen-dence of the mean grain size of the bcc phase estimated from broadening its relation to the peak in the X-ray diffraction patterns using Eq (2) It should be noted that the growth of a-Fe(Si) is controlled by the slow diffusion of Nb and Cu which leads to a nanocrystalline structure As can be seen
Fig 2 DSC curves for Fe 73.5 Si 15.5 Nb 3 Cu 1 B 7 ribbons (as-cast and annealed
at 540 8C for 30 min).
Fig 3 X-ray diffraction pattern (in the upper panel) and TEM image (in the lower panel) for the Fe 73.5 Si 15.5 Nb 3 Cu 1 B 7 amorphous alloy annealed at
540 8C for 30 min.
Fig 4 The annealing temperature dependence of the mean grain size of the bcc phase estimated from the broadening of the relations in the X-ray diffraction patterns using Eq (2).
Trang 4clearly fromFig 4, the mean grain size is about 12 nm and it
remains almost constant until the annealing temperature
reaches 540 8C This indicates that the primary
crystal-lization (the first peak of the DSC curve inFig 2) is actually
the formation of nanocrystalline structure, where a-Fe(Si)
grains are embedded in an amorphous matrix [see the TEM
image inFig 3(b)] Annealing at higher temperatures not
only leads to grain growth of a-Fe(Si), but also additional
phases are formed from the amorphous matrix phase at TaZ
650 8C This second stage of crystallization corresponds to
the second peak in the DSC curve (Fig 2) and boride phases
(e.g Fe3B and Fe2B) are found
3.2 Magnetic characteristics
The crystallization kinetics of the ribbons can be
observed by measurements of thermomagnetic curve, as
shown inFig 5 It is clear to see from this figure that the
ribbon is amorphous at room temperature As the
temperature increases, the magnetization is abruptly
reduced marking the Curie temperature (TC) of the
amorphous phase With further increasing temperature, the
magnetization is small and constant over a large
tempera-ture interval up to a region where crystallization of a-Fe(Si)
leads to an increase of the magnetization The increase of
the magnetization at the crystallization onset (w500 8C
seen in the DSC curve ofFig 2) indicates the formation of
some crystalline magnetic phase(s) On returning from high
temperature, a large amount of a-Fe(Si) grains are
crystal-lized in the sample and this leads to a strong increase of the
magnetization below the TCof a-Fe(Si) [see the curve 2 in
Fig 5] This reflects that any variation in the magnetic
nature of the amorphous phase could change the intergrain
exchange coupling and consequently the magnetic softness
of the nanocomposite material
In order to further evaluate influences of annealing on the
magnetic properties, we measured hysteresis loops and the
annealing-temperature dependence of the coercivity (Hc) is
displayed inFig 6 It is clear that the coercivity decreased
with increasing annealing temperature (Ta) up to 540 8C and then increased at higher temperatures This can be interpreted as following: the gradual decrease of Hcat Ta
well below the onset crystallization temperature (i.e w500 8C, see Fig 2) is a result of structural relaxation, while the drop of Hc in the temperature range of the first crystallization stage (w540 8C) is likely due to the appearance of nanosized a-Fe(Si) grains where magneto-crystalline anisotropies are averaged out Annealing over
540 8C caused a rapid increase of Hc, indicating a large degradation of the soft magnetic properties This coincides well with microstructural change (i.e the abrupt increase of the mean grain size for annealing above 540 8C as seen in
Fig 4) In this case, the increase of nanoparticles size can considerably reduce the magnetic exchange coupling in the nanocrystalline material [9] Furthermore, it is found that the change of Hcwith annealing temperature is correlated well to the temperature dependence of the permeability, where the permeability resulting from the rotational magnetization increased with increasing annealing tem-perature up to 540 8C and then decreased at higher temperatures [13] It is known that the permeability is inversely proportional to the coercivity in the temperature range investigated
3.3 Magnetoimpedance analyses The magnetoimpedance ratio DZ/Z can be defined as
DZ=Zð%ÞZZðHÞ=ZðHmaxÞK1 where Hmax is the external magnetic field sufficient to saturate the impedance and equals to 150 Oe in the present study The GMI profiles of the amorphous samples annealed at different temperatures ranging between 350 and 650 8C were measured and used
to assess the anisotropy field
As reported in Ref [17], the contribution of the transverse permeability to GMI from magnetization rotation becomes dominant in the high frequency range (w10 MHz) and a simple single-domain model was proposed According
to this model, the width of measured GMI peak could reflect
Fig 5 Thermomagnetic curves of the Fe 73.5 Si 15.5 Nb 3 Cu 1 B 7 amorphous
alloy: (1) heating cycle and (2) cooling cycle.
Fig 6 The coercive force (H c ) as a function of annealing temperature for
Fe 73.5 Si 15.5 Nb 3 Cu 1 B 7 alloys annealed for 30 min.
Trang 5the distribution of anisotropy field As shown inFig 7, at a
fixed frequency of 10 MHz, the anisotropy field and GMI
change sensitively with annealing temperature This also
implies that the permeability in the transverse direction
changes sensitively with annealing temperature [13] The
changes in anisotropy field (Hk, as depicted inFig 7) and
the magnitude of GMI [DZ/Z(%)] are plotted as a function
of the annealing temperature inFig 8 It is clear that, with
increasing temperature up to 540 8C, a decrease of the
anisotropy field and an increase of GMI were observed, but
an opposite tendency was found when the annealing
temperature exceeded 600 8C This is respectively related
to the increase of magnetic softness and the microstructural
change of the sample as the annealing temperature is
increased, as discussed in Sections 3.1 and 3.2 These results
also coincided with the annealing-temperature dependence
of the magnetostriction saturation and the effective
anisotropy constant evaluated by separate magnetization
measurements[4–8]
Now let us discuss the interaction between the magnetic
properties and the GMI effect in the Fe-based amorphous
alloy upon annealing by considering a two-phase random
anisotropy model[9] Within the framework of this model,
the nanocrystalline grains in nanocrystalline alloys are
strongly coupled through magnetic exchange interactions, and the local magnetocrystalline anisotropies of grains are averaged out Meanwhile, the intergranular amorphous phase plays an indispensable role, because, only through
it, can the exchange coupling be conveyed Thus, any variation in the magnetic nature of the amorphous phase will consequently change the intergrain exchange coupling, then alter the magnetic softness and the effective anisotropy, and finally modify the GMI features Here, we assume that, for
an amorphous alloy (i.e as-cast state), the amorphous phase
is ferromagnetic and maintaining the exchange coupling As the amorphous sample was annealed at a temperature close
to the crystallization temperature of the soft magnetic phase
of a-Fe(Si), a combination of stress release and the magnetocrystalline anisotropy decrease in the amorphous phase further softens the ribbon magnetically, thus enhance the GMI effect In the present work, the optimal GMI profile was observed for the alloy annealed at 540 8C, as a result of the largest increase in magnetic softness (i.e the largest permeability and the smallest coercivty as seen in Fig 6) The annealing of amorphous ribbons drastically reduced the coercive force and increased the effective magnetic permeability, thus resulted in an increase in GMI effect When annealing temperatures were relatively high, e.g over
600 8C, and close to the crystallization temperature of the hard magnetic Fe-B phase (725 8C, see Fig 2), annealing may damage the soft magnetic phase of a-Fe(Si) and cause a ferromagnetic to paramagnetic transition, the material becomes incapacitated in conveying the intergrain magnetic exchange coupling, an overwhelming decrease in GMI was observed
4 Conclusions
A thorough study of the effect of annealing on structural and magnetic properties and the giant magnetoimpedance effect in the Fe73.5Si15.5Nb3Cu1B7 amorphous alloy has been made It is found that the mean grain size of the a-Fe(Si) crystallites in the order of 12 nm remains almost unchanged until the annealing temperature reached 540 8C The decrease of anisotropy field and the increase of GMI with increasing annealing temperature up to 540 8C were observed and ascribed to the increase of the magnetic permeability and the decrease of the coercivity, whereas the opposite tendency was found for the sample annealed above
600 8C which is likely due to the microstructural change caused by high-temperature annealing This indicates that variation in the magnetic characteristic of the amorphous phase upon annealing changed the intergrain exchange coupling This altered both the magnetic softness and the effective anisotropy and consequently modified the GMI features It is proposed that the temperature-dependent GMI profile is useful to further understand the magnetic exchange coupling between these grains through the amorphous boundaries in Fe-based nanocrystalline materials
Fig 7 GMI profile at fZ10 MHz in Fe 73.5 Si 15.5 Nb 3 Cu 1 B 7 as-cast and
annealed alloys.
Fig 8 Variation of the anisotropy field and magnitude of GMI with
annealing temperature.
Trang 6The authors wish to acknowledge the Scientific
cooperation between UK, Korea and Vietnam Research at
Chungbuk National University supported by the Korean
Science and Engineering Foundation through the Research
Center for Advance Magnetic Materials at Chungnam
National University Research at Center for Materials
Science was supported by the Vietnam National Program
for Fundamental Research Grant No 420110
References
[1] McHenry ME, Laughlin DE Nano-scale materials development for
future magnetic applications Acta Mater 2000;48:223–38.
[2] Lachowicz HK Magnetic materials-progress and challenges J Tech
Phys 2001;42(2):127–48.
[3] Jiles DC Recent advances and future directions in magnetic materials.
Acta Mater 2003;51:5907–39.
[4] Yoshizawa Y, Oguma S, Yamauchi K New Fe-based soft magnetic
alloys composed of ultrafine grain structure J Appl Phys 1988;64(10):
6044–6.
[5] Tate BJ, Parmar BS, Todd I, Davies HA, Gibbs MRJ, Major RV Soft
magnetic properties and structures of nanocrystalline Fe–Al–Si–B–
Cu–Nb alloy ribbons J Appl Phys 1998;83(11):6335–7.
[6] Crisan O, Le Breton JM, Filoti G Nanocrystallization of soft
magnetic Finemet-type amorphous ribbons Sens Actuators, A 2003;
106:246–50.
[7] Ku W, Ge F, Zhu J Effect of magnetic field annealing on the giant magnetoimpedance in FeCuMoSiB ribbons J Appl Phys 1997;82(10): 5050–3.
[8] Hernando B, Sanchez ML, Prida VM, Tejedor M, Vazquez M Magnetoimpedance effect in amorphous and nanocrystalline ribbons.
J Appl Phys 2001;90(9):4783–90.
[9] Herzer G In: Buschow KHJ, editor Handbook of magnetic materials Amsterdam: Elsevier Science; 1997 p 415 [Chapter 3].
[10] Alben R, Becker JJ, Chi M Random anisotropy in amorphous ferromagnets J Appl Phys 1978;49(3):1653–8.
[11] Kim YK, Cho WS, Kim TK, Kim CO, Lee HB Temperature dependence of magnetoimpedance effect in amorphous Co 66 Fe
4-NiB 14 Si 15 ribbon J Appl Phys 1998;83(11):6575–7.
[12] Li DR, Lu ZC, Zhou SX Magnetic anisotropy and stress-impedance effect in Joule heated Fe 73.5 Cu 1 Nb 3 Si 13.5 B 9 ribbons J Appl Phys 2004;95(1):204–7.
[13] Phan MH, Peng HX, Wisnom MR, Yu SC, Kim CG, Nghi NH Effect
of annealing temperature on permeability and giant magneto-impedance of Fe-based amorphous ribbon Sens Actuators, A [in press].
[14] Phan MH, Peng HX, Wisnom MR, Yu SC, Chau N Enhanced G.M.I., effect in a Co 70 Fe 5 Si 15 B 10 ribbon due to Cu and Nd substitution for B Phys Stat Sol (a) 2004;201(7):1558–62.
[15] Leu MS, Chin TS Quantitative crystallization fraction and nano-grain size distribution studies of a FeCuNbSiB amorphous alloy MRS Symp Proc 1999;557:557.
[16] Cullity BD Element of X-ray diffraction 2nd ed Reading, MA: Addison-Wesley; 1978 p 102.
[17] Ryu GH, Yu SC, Kim CG, Yoon SS Evaluation of anisotropy field in amorphous Fe 71Cx Nb 7 B 22-x alloys by GMI measurement J Magn Magn Mater 2000;215–216:359–61.