Kirigami là nghệ thuật cắt giấy truyền thống của Nhật Bản, với tên gọi được ghép từ hai chữ : “kiru” (có nghĩa là cắt) và “kami” (là giấy). Tính đối xứng là đặc điểm nổi bật nhất trong kirigami truyền thống. Hình bông tuyết, ngũ giác, và bông hoa là những hình ảnh cổ điển quen thuộc đặc trưng cho kirigami mà trong đó, cắt giấy đơn thuần chỉ nhằm tôn lên cấu trúc tối giản, cân xứng nhưng cũng rất linh hoạt của thiết kế. Nghệ thuật cắt giấy được cho là lần đầu tiên xuất hiện trong các đền chùa Nhật Bản như một cách thể hiện lòng thành kính trước các vị thần. Đến khoảng thế kỷ XVII, Kirigami được biết đến rộng rãi khắp châu Á như một hình thức nghệ thuật đích thực. Không chỉ riêng ở Nhật mà cả ở Trung Quốc, người ta tạo nên các thiết kế kirigami để biểu trưng cho những điều tốt đẹp và quan trọng như: Thịnh vượng, Hoàn hảo, Quý phái, Trang nhã hay thậm chí là mối liên kết giữa con người và vũ trụ. Bunraku, một loại hình múa rối Nhật Bản đôi lúc cũng sáng tạo những con rối bằng giấy từ kỹ thuật Kirigami, nhưng vẫn đảm bảo các bộ phận có thể cử động được.
Trang 11
5
6
7 12
13
14
15
8
10
11
9
2 3
4
4
3
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold
Valley fold(dashed and dotted line)
Make a valley fold
Scissors line(solid line)
Cut along the line
Cut in line(solid line)
Cut along the line
Glue spot(Red dot)
Glue parts with the same number together
Glue spot(Green dot)
Glue within the same part
Glue spot(Blue dot)
Glue to the rear of the other part
Glue
The glue spot(colored dot) shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children
View of completed model
Assembly Instructions:Two A4 sheets(No.1 to No.2)
*This model was designed for Papercraft and may differ from the original in some respects
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order
Moai statues, Chile: Assembly Instructions Canon ® is a registered trademark of Canon Inc © Canon Inc © Y.Watanabe
http://www.canon.com/c-park/en/
Indicates where sections should
be glued together.
Before starting assembly:Writing the number of each section on its back side before cutting out the sections is highly recommended
(* This way, you can be sure which section is which even after cutting out the sections.)
The surface of part 4 with the triangle is the front side
The surface of part 3 with the red triangle on the glue tabs is the front side.Keep these points in mind when gluing the parts together
Glue the dark-colored glue tabs to part 10
Glue parts 1 - 4 after first gluing parts 5 and 6
Parts 1 - 11
Parts 1 - 8
Glue so that the seams
on the rear surface match
Trang 217 16
17
18
30
32
36
35 38
37
29 29
31 25
26
27
28
21
23
24
22
30 31
Moai statues, Chile: Assembly Instructions Canon ® is a registered trademark of Canon Inc © Canon Inc © Y.Watanabe
The surface of part 16 with
the triangle is the rear side
Glue part 17 so that its seams
align with the triangle on part 16
* Build the two statues in the same way
First glue parts 18 and
19 together, then glue
to part 17
Glue the dark-colored
glue tabs to part 23
Glue so that the seams
on the rear surface match
Parts16 - 24
Parts 16 - 21
Finished!