Kirigami là nghệ thuật cắt giấy truyền thống của Nhật Bản, với tên gọi được ghép từ hai chữ : “kiru” (có nghĩa là cắt) và “kami” (là giấy). Tính đối xứng là đặc điểm nổi bật nhất trong kirigami truyền thống. Hình bông tuyết, ngũ giác, và bông hoa là những hình ảnh cổ điển quen thuộc đặc trưng cho kirigami mà trong đó, cắt giấy đơn thuần chỉ nhằm tôn lên cấu trúc tối giản, cân xứng nhưng cũng rất linh hoạt của thiết kế. Nghệ thuật cắt giấy được cho là lần đầu tiên xuất hiện trong các đền chùa Nhật Bản như một cách thể hiện lòng thành kính trước các vị thần. Đến khoảng thế kỷ XVII, Kirigami được biết đến rộng rãi khắp châu Á như một hình thức nghệ thuật đích thực. Không chỉ riêng ở Nhật mà cả ở Trung Quốc, người ta tạo nên các thiết kế kirigami để biểu trưng cho những điều tốt đẹp và quan trọng như: Thịnh vượng, Hoàn hảo, Quý phái, Trang nhã hay thậm chí là mối liên kết giữa con người và vũ trụ. Bunraku, một loại hình múa rối Nhật Bản đôi lúc cũng sáng tạo những con rối bằng giấy từ kỹ thuật Kirigami, nhưng vẫn đảm bảo các bộ phận có thể cử động được.
Trang 1out the sections.) Indicates sections that should be glued first, then cut out.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold
Valley fold(dashed and dotted line)
Make a valley fold
Scissors line(solid line)
Cut along the line
Cut in line(solid line)
Cut along the line
Glue spot(Red dot)
Glue parts with the same number together
Glue spot(Green dot)
Glue within the same part
Glue spot(Blue dot)
Glue to the rear of the other part
Glue The glue spot(colored dot) shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
Photo of competed model
Assembly Instructions:Six A4 sheets(No.1 to No.6)
*This model was designed for Papercraft and may differ from the original in some respects
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order
http://www.canon.com/c-park/en/
Miniature stand Star-shaped stand
Choose the stand you like best
Build parts 2 and 4 in the same way
Attach the reinforcement with glue first
Align and glue the rear surfaces together
Align and glue the rear surfaces together
Align and glue the rear surfaces together
Build four identical versions of part 10
View of completed model
Fold these parts inward and align and glue their surfaces together
Trang 2Align and glue the rear surfaces together
Position the short side
on this side
Position the elevator
entrance on this side
*Glue the parts together in the sequence shown in steps 1 - 6
Trang 3Curve the interior side
of this part
View from rear
Position so that the narrower side is located on this side
After positioning the rear surfaces
of the side parts together, glue the rear sides of the corners together
Insert and glue to the rear surface
* Cover the statue with the upper robe
No gluing is necessary
Trang 4Cut after gluing the rear surfaces together
Glue the rear surfaces together
Glue the rear panels of parts 41 and 43,
between which the four sheets of part 42
are sandwiched
Glue the statue's fingertips here
Fold the fingertips inward and glue to the Declaration of Independence
Lightly bend this part as
shown in the illustration
Insert to assembled part 47 along this line
Insert and glue the glue tabs
to the interior side of this spot
Glue to part 29 on the interior side
Trang 5Miniature stand
*Position in place No gluing needed
Finished!
Trang 6Star-shaped stand
*Position in place without gluing
*Place this part on the stand without gluing
Finished!