Kirigami là nghệ thuật cắt giấy truyền thống của Nhật Bản, với tên gọi được ghép từ hai chữ : “kiru” (có nghĩa là cắt) và “kami” (là giấy). Tính đối xứng là đặc điểm nổi bật nhất trong kirigami truyền thống. Hình bông tuyết, ngũ giác, và bông hoa là những hình ảnh cổ điển quen thuộc đặc trưng cho kirigami mà trong đó, cắt giấy đơn thuần chỉ nhằm tôn lên cấu trúc tối giản, cân xứng nhưng cũng rất linh hoạt của thiết kế. Nghệ thuật cắt giấy được cho là lần đầu tiên xuất hiện trong các đền chùa Nhật Bản như một cách thể hiện lòng thành kính trước các vị thần. Đến khoảng thế kỷ XVII, Kirigami được biết đến rộng rãi khắp châu Á như một hình thức nghệ thuật đích thực. Không chỉ riêng ở Nhật mà cả ở Trung Quốc, người ta tạo nên các thiết kế kirigami để biểu trưng cho những điều tốt đẹp và quan trọng như: Thịnh vượng, Hoàn hảo, Quý phái, Trang nhã hay thậm chí là mối liên kết giữa con người và vũ trụ. Bunraku, một loại hình múa rối Nhật Bản đôi lúc cũng sáng tạo những con rối bằng giấy từ kỹ thuật Kirigami, nhưng vẫn đảm bảo các bộ phận có thể cử động được.
Trang 1View of completed model
* Build the model by carefully reading the Assembly Instructions, in the parts sheet page order
* Assembly will be easier if you write the part's number on the back of each part
No of Parts : 69(Including 2 spare parts)
Assembly Instructions : Five A4 sheets Parts sheet (Pattern) : Ten A4 sheets
Assembly tip: Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff
South face
North face West face
East face
The Florence Cathedral is a world heritage listed gothic-style basilica, and is a famous landmark of the
historical district of Italy's Florence Construction of the basilica began in 1296, and took more than
140 years to complete The Florence Cathedral is composed of three buildings: the"Duomo," which is
famous for its huge dome roof and is the fourth-biggest cathedral in the world;
the "Baptistery of San Giovanni," an octagonal building famous for the "Gates of Paradise;"and
"Giotto's Bell Tower," which stands to the side of the Duomo
The white, green, and red marble exterior of the Cathedral is decorated with beautiful sculptures and
mosaic works from many different artists
Trang 2Each page of the "Parts sheet" has a sheet number in the top left-hand corner (Sheet No.2 No.10)
Work in order of these sheet numbers
Each part has a "parts number" printed on it Also, each glue tab is marked with one of three symbols
indicates glue tabs to be attached to connection areas within the same part
For glue tabs marked with a number, attach them to the glue tab with the same number
on the connection areas of other parts
For glue tabs marked with a "parts number," attach them to the part with the number printed
Check the diagrams in the "Assembly Instructions" carefully for each part as you work
Before starting
The numbers in the Assembly Instructions indicate the order to attach parts
Follow this order when attaching
For small parts, assembly
will be easier if you use a
slightly thinner type of paper.
Handy Hint
Attach the red circled area of 2B
to the part of 2D indicated
by the arrow as shown
* The raised up part of the roof peak
Sheet No.2
Sheet No.3
* Glue together the inside edges
of the seam to make the roof peak stand up.
Trang 3For small parts, assembly will be easier if you use
a slightly thinner type of paper.
Handy Hint
There are spares provided for the small parts,
to use in case of misplaced parts or cutting errors
Attach the cross so that it faces the east-west direction.
Align the reverse sides and attach
South North
West
East
Mountain fold
Valley fold
Attach 25 and 26
in the same way.
* Attach to the areas labeled 14, 15, and 16 on part 8A of the display stand
Attach parts 4D 4K to the areas of 4C as shown
Trang 4Sheet No.6, 7
Sheet No.8, 9, 10
Sheet No.6
Sheet No.7
Sheet No.10
Sheet No.9
Sheet No.8
* After completing the display stand, attach the buildings to the areas shown.
Trang 5Florence Cathedral, Italy : Assembly Instructions
Sheet No.9, 10
Sheet No.9
Sheet No.10
View of completed model
South
North
West East
entrance
Attach the face with the entrance (shown above)
so that it faces the east direction.
* Attach the short side flaps inside.
* Attach the four corners.
* Fold in the center, and glue the reverse sides.
* Attach the buildings
to the completed display stand.
* Glue this side