cac ky hieu su dung trong may cnc

Feed hold: during the auto program running, the machine will stop cutting when the feed hold push button is pressed if the accident happened.. Auto mode: when the mode selection switch i

B1.1 Function description

The setting display of the CRT please refer to manual supplied from the controller builder

CRT/MDI control panel：

The controller panel including CRT and function key and power control push buttons。

※ FANUC-0i-TC

B1.2 Element functions of machine operator panel

Power switch：POWER ON

Power switch：POWER OFF

Cycle start push – button

Feed hold:

during the auto program running, the machine will stop cutting when

the feed hold push button is pressed if the accident happened And the

program can be resumed by push the cycle start push – button EMG STOP Emergency stop

Data write protect switch:

only when the switch is set to 〝on〞the program could be edited, inserted or deleted

Auto mode:

when the mode selection switch is set to 〝auto〞mode，the CRT would the program, and be executed

Transmitting and working at the same time:

Read out data through PC or CNC as turn the button to this position

M.D.I mode:

manual data input mode, and the parameters and program could be

dited at this mode

Handle mode:

At the handle mode, the axis selection switch is fed by turning the pulse

Handle。axis feed amount per pulse conforms to the setting of the

handle switch

JOG mode: Press directional button to do axis-feed

RAPID mode: Press directional button to move rapidly as

Zero return

Single block:

when this switch is pressed, the indicator is lit, and automatic operation is executed by one block

When the indicator is off, The program is executed

continuously

M01 stop:

when the switch is pressed, the indicator is lit, and the machine will

become feed hold when the block with M01 is executed

Dry run:

this function is used to check the program when this program Is executed at first time and it is valid only when the indicator lit

Block skip:

when the switch is pressed, the indicator is lit, and the block with the

〝/〞will be ignored

Spindle JOG: To adjust spindle RPM by manual

Spindle ccw rotate push button:

spindle counter clockwise rotates, is equal to the M04

command

Spindle stop push button:

spindle stops rotates, is equal to the M05 command

Spindle cw rotate push button: Spindle clockwise rotates, is equal

to the M03 command

C axis cw rotate push button.

C axis ccw rotate push button

Press direction key with〝KEEP〞three second to move continuously

To move X-axis in〝﹢〞direction

To move X-axis in〝﹣〞direction

To move Z-axis in〝﹢〞direction

To move Z-axis in〝﹣〞direction

Rest Apparatus: When this light is on , machine automatically shutdown while M30 code read in

Spindle neutral gear indicator M40﹙ ﹚

Auto Shut-down

Spindle low gear indicator M41﹙ ﹚

Spindle Middle gear indicator M42﹙ ﹚

Spindle Middle-high gear indicator M43﹙ ﹚

Spindle high gear indicator M44﹙ ﹚

Chip conveyor switches: Press and move back

Chip conveyor switches: Press to go forward continuously Press again to stop

Tool changing push button

In reserve key

choose V12 Tools

choose H4 Tools.

Coolant on/off switch

Work lamp switch

Machine lock:

all the axes would not move, but the value of the coordinate will change

on the screen

Note: The zero return procedure should be done when turn off the function

X axis zero return indicator: When X axis return to the zero position

, the indicator will get lit

Z axis zero return indicator: When Z axis return to the zero position

, the indicator will get lit

C axis zero return indicator: When C axis return to the zero position

, the indicator will get lit

Hydraulic chuck pilot lamp

Selectivity program stop pilot lamp.

CNC alarm pilot lamp

Lube alarm pilot lamp

Coolant alarm pilot lamp

Machinery alarm pilot lamp

Hydraulic chuck open

Hydraulic chuck close

Program protect

Program not protect

Rapid feed rate override:

F0 : 1% of the rapid feed rate

F25 : 25% of the rapid feed rate

F50 : 50% of the rapid feed rate

F100: 100% of the rapid feed rate

Spindle speed override switch:

The switch is used to override the spindle speed For instance, if the spindle speed is 100 rpm in program, and the switch is set to 60%, then the spindle speed will reduce to 60 rpm

Spindle speed adjustment switch:

this switch at the jog or handle mode could adjust the spindle speed

Note: Do not make change the spindle turn to opposite direction repeatedly, it will damage the gear

JOG feed ride:

The programmed feed rate is adjuration form 0 to 150% in increments of 10%

Mode selection button

Turret indexing switch

Load meter: Spindle load meter

OT Over travel release:If X or Z axis over travel, press this button and use handle to

move these axes

Quá cữ hành trình

Nếu trục X hoặc trục Z quá cữ, nhấn nút này và sử dụng chế dộ quay tay tạo xung đễ đưa về

Fast servomotor turrets to zero: Turn the tool switch to tool NO.1 and

Choose V12 turret, Then put the tool change button