Properties, prossesing of natural fiber

SCES 3354 Composite Materials Title – Preparation, properties and application of natural fibre as reinforcement for polymer matrix composites.. Properties of wool fibre composite • Effec

SCES 3354 Composite Materials Title – Preparation, properties and application of natural fibre as

reinforcement for polymer matrix composites.

Group’s members:

Farhatun Najat Bt Maluin (SEZ090048) Fatem Hamime Bt Ismail (SEZ090007) Siti Artikah Bt Mahmud Safbri (SEZ090034) Nur Feeza Ashiqin Harun (SEW090023) Siti Noornabila Suhada Abdillah (SEW090030)

Fibre reinforced polymer

Fibre as reinforcing phase

- to enhance the strength and elasticity of plastic

Matrix phase – polymer

- act as a binder and a medium to tranfer stresses between reinforcing fibers.

1) INTRODUCTION

• Composites = combinations of two or more materials

- which is reinforcing phase (fibre) and matrix phase

Types of polymer matrices

Thermoset

- Above its melt point, the plastic liquefies

(softens enough to be processed).

This process can be repeated, with the plastic

melting and solidifying as the temperature

climbs above and drops below the melt

- The exposure to high heat will cause the material to degrade, not melt

The advantage of thermoplastics over thermosets are thermoplastics has higher elongation at break Thus, it is necessary in order to improve impact strength

Pro duci

ble with

low ow at l ent estm inv cost

renewable source, requires

little energy during production and use carbon dioxide while oxygen is given back to the environment.

They are environmentally

friendly materials at the

stage of production,

processing and waste

Good the

rm

al a

nd a coust

ic s tie per pro ing lat insu

Advantages of natural

fibre composites

Classification of natural fibers

PLANT FIBRE

• The fibers are normally a rigid, crystalline cellulose micro fibril-reinforced

amorphous lignin and with hemicellulosic matrix

• Mechanical structural of plant fibers is much lower when compared to reinforcing glass fiber

• Somehow, because of the low density, their properties for such the strength and the stiffness of the plant fibers are comparable to the values of glass fibres

Properties of the plant fibers.

one of the type of natural fiber that consist of cellulose,

hemi-cellulose, lignin, pectin

(the detail will be disscussed further in the part 2)

Classification of

animal fibre

Animal Hair

- wool, human hair, feather Silk fibre

ANIMAL FIBRE

- Generally compromise of proteins

Example - Wool

Properties of wool

• low tenacity because it has excellent elongation and elastic recovery

• durable with moderate resistance and it is also poor conductor of heat

• very sensitive to some alkalis

• give influence on the tensile stress or modulus of elasticity with increasing fraction of wool content

• when arranged in a transverse position to the tensile load, the tensile stress was increased

• may be able to provide reinforcement in multi-axial situations.

Properties of wool fibre composite

• Effect of orientation of fibre

- transverse position increase the tensile stress and toughness.

- The modulus of elasticity does not effected fibre samples

Shearing SORTING CLEANING CARDING SPINNING WEAVING FINISHING

Processing and extraction of wool fibre

• As a composite, wool fibres have been combined with polyester fibres and spun into multistrand yarn as threads

• Traditionally, wool fibres have been spun into multilayer fibres in the form of

threads, then knitted into cloth and utilized for the manufacture of garments

• The composite matrix was prepared from polyester resin with 1% hardener

(methyl ethyl ketone peroxide)

• Samples of composite sheets were prepared in the laboratory from skeins of wool laid alternatively with layers of resin mixture, and placed in a rectangular mould

Application of wool fiber

• used as alternatives for producing composite materials which may have great scope in value added application including bio-engineering and medical applications

• In the textile industries, a lot of waste wool fibers and their products induce actions which lead to the regeneration of wool keratin materials

• Animal fiber reinforced composite - applications in the automotive, aerospace and sports equipment industries

• Advantage of animal fiber composite materials is that they can be tailored to meet the specific structure such as face brush makeup, blanket etc.

MINERAL FIBRE

• the only naturally occurring of mineral fibre – asbestos

• Asbestos fibres are silicate compound which contain silicon and oxygen in their molecular structure.

• The crystal in these fibres forms a long, thin and flexible fibre when separated

This is a piece of asbestos rock Can you see the fibers?

Asbestos fibers as seen through a microscope

Properties of asbestos fibre

• Resistance to fire or inflammable

• Poor thermal and heat conductor

• High tensile strength and flexible

• Insoluble in water

• their colours depend on the types and the composition of the asbestos which is depends on the amount of iron.

Properties of asbestos fibre composite

• The mechanical properties depends on;

i) The orientation of the fibre

In axial orientation, the composite shows the higher tensile strength while in radial orientation, the composite shows the higher compressive strength

(Lee & Kim, 2004)

ii) The percentage of fibre mass fraction

The increase in the volume of fibre, increase the impact resistance of the polymer (Akens & Garret, 1986)

Processing and extraction of asbestos fibre

1st step - Mining process – open-pit mining extracts the rock or minerals from the earth by remove it from an open pit or borrow.

2nd step - Milling process

- extraction of the fibre from the ore

- separation and degradation of fibre according to its lenght

Dry milling the fibre extraction were done by crushing

the ore using different series of crushing

machine and pass to vacuum aspiration on a

vibrating screen

Wet milling the asbestos is dispersed through the water and not being dried until the separation process of fibre was completed

Processing of asbestos fibre composite.

Schematic diagram of a typical Hatschek process, where are slurry (1),Cement (2), asbestos (3), limestone filler (4) ,water (5) , vats (6), sieve cylinders (7), running felt (8), Vacuum (9), formation cylinder (10), Green lamina produced (F)

cutting of the green lamina (11), moulding (12) , finish product (P)

Most widely method - Hatschek process (or wet process)

- This process produce the fibre cement sheets by stacking together the thin lamina which is made from a suspension (slurry) of cement, fibre, limestone filler and water

Application of asbestos fibre

• Used in making fireproof materials and also insulation products (thermal and electrical)

• Widely used for the fabrication of papers and felts for flooring and roofing products.

• Develop products for the automotive, electronic, and printing industries.

roofingInsulating board

insulating pipe

Problems of asbestos fibre

• Unfortunately, asbestos can cause health effects when the fibres are breath into the lungs or being swallowed into the body and eventually accumulate in the bodies and lodged in tissues

• This can lead to the lung cancer, mesothelioma (a cancer of the linings around the lungs and abdomen), asbestosis (scarring of lung tissue that impairs in breathing) and eventually can lead to the death

• But the low levels exposure of asbestos can’t be harmful to human body

• Thus, precaution steps must be taken when handling this fibre

Some of the precaution steps.

• Wear coveralls and an approved respirator

• Do not use abrasive cutters and sanders on asbestos cement products.

• Wet down material to reduce the release of dust

• Work in well ventilated areas where possible

• Immediately dispose of smaller asbestos pieces and collected dust in plastic bags, which are clearly labelled asbestos waste.

2) Natural fibre which can be used as reinforcement of polymer

STEM FIBRE

Example – Jute fibre

• This fiber are extracted from the ribbon of the stem

• Use retting process in extracting this this kind of fiber from the long lasting life stem or the bast

• give more application toward strength, lightweight and noise absorption

Properties of Jute fibre

• favor moderately high specific strength and stiffness

• cheap with high performance composite

• easy availability, low cost, high strength (tensile

strength)

• developed with different thermoplastic and thermoset polymers such as jute reinforce polyester, epoxy composite and jute reinforced polypylene.

Propertis of Jute-polyester Composite

• High in mechanical properties

• The percentage of fibre volume affetcs the composite mechanical properties such as tensile, strain, toughness and moduli.

Processing and extraction of jute fibre

• The process - retting process

• To extract fine fibers from jute plant,

- the first parameter were considered is if the fiber can be easily removed from the jute hurd or core before the crop been harvested.

• Jute stalk after harvesting are submerged in soft running water in

• Give advance in strength, lightweight and noise absorption

• commercially important in the automotive and building industry, i.e roofing

• As decorative, vast, in sacking, yarn and carpet backing, all now replaced by synthetic fibres

FRUIT FIBRE

Example – Banana fibre

• Banana fibers obtained from the stem of banana plant (Musa sapientum) present important advantages such as low density, appropriate stiffness and mechanical properties and high disposability and renewability

• Banana fiber was used because of its ability to be produced in a continuous form, and hence able to be produce into woven mat form

Properties of banana fibre

•chemical composition are cellulose, hemicellulose and lignin

•is better in terms of fineness and spinnability which include ring spinning, open-end spinning, bast fiber spinning and semi-

worsted spinning

•highly strong fiber, has smaller elongation and its weight is light.

•it has strong moisture absorption quality

•can be categorized as eco-friendly fiber because it is

bio-degradable and has no negative effect on environment

Properties of banana-polyester composite

• the percentage volume fractions of banana fibre effects the tensile strength.

- The results shows that an increasing of percentage volume fractions of

banana fibre increase the the tensile modulus of the composite

- While, for the tensile strength, only after 0.1% volume fraction of the fibre, the tensile strength increase gradually.

Processing and extraction of banana

fibre

Japanese

method Nepalese method

Japanese method

• In the Japanese method of making banana fiber, the care is taken as early from the plant cultivation stage

• To ensure their softness, the leaves and shoots of the

banana plant are pruned periodically

• harvested shoots are first boiled in lye to prepare the fibers for making the yarn, whereas at the same time the banana shoots give away fibers having varying degrees of softness.

• As a results, different qualities of yarns and textiles

produced that can be used for specific purposes.

different qualities of yarns and textiles produced that can be used for specific purposes

The outermost fibers of the shoots are

the coarsest ones and more suitable for

making such home furnishing as

tablecloth

While the innermost part of banana fiber

is the softest and widely used for making kimono and kamishimo, the traditional

Japanese apparels

Nepalese method

• Second method is Nepalese method in which the trunk of the banana plant is harvested instead

of the shoots

• The steps

1) small pieces of these trunks are put through a softening process for mechanical extraction

of the fibers, bleaching and then drying to produce fiber that has appearance similar to silk.

- During the processed, only the aged bark or the decaying outer layers of the banana plant are harvested and soaked in water to quicken the natural process

2) After that, when all the chlorophyll is dissolved and only cellulose fibers remain, they are extruded into pulp so that they may become suitable for spinning into yarn.

3) The yarn is then hand-dyed and these rugs are woven by hand –knotted methods again by the women of Nepal.

Applications of banana fibre

• The application of banana fiber only limited for making items like ropes, mats and some other composite materials

• home furnishings

• used to make fine cushion covers, necties, bags, table cloths, curtains

• due to its being lightweight and comfortable to wear, Japan people also

preferred to use kimono and kamishimo as summer wear.

The fibres are manually placed into a

one-sided gel coated male or female mould

A matrix of thermosetting resin is rolled

onto the fibres using an hand roller

More layers can be added and, after drying,

the composite part can be removed from the

mould

The processing of the plant fibres composite.

• Hand lay up process:

The mould is closed and pressure is then applied to

force the material to fill up the entire mold cavity

Excess material is channelled away by the overflow

grooves

The heat and pressure are maintained until the

plastic material is cured

• Compression moulding process:

• By using natural fiber composites, they would be sustainable and biodegradable Thus,

it is good in other to save our environment.

THANK YOU

FOR LISTENING