NC2000 system operation manual vol1

NC2000 System Operation ManualV2.0 Volume I System Installation NARI Group Corp... It includes four parts: Volume I, Introduction of installation processfor NC2000 system, including inst

NC2000 System Operation Manual

V2.0

Volume I System Installation

NARI Group Corp.

April.2006

Copyright Announcement

Warning: This Computer Program is protected by copyright law and internationaltreaties Unauthorized reproduction or distribution of this program, or any portion of it,may result in severe civil and criminal penalties, and will be prosecuted to themaximum extent possible under the law

、 is registered trade mark of NARI Group Corp

@ 2004 Nanjing Automation Research Institute All rights reserved

NC2000 is new generation computer monitoring & control software developedfor electric power system, and it is based on the experience accumulated by Nariaccess system used in many hydropower plants This system use Client/Serverstructure, support different hardware, operating system and relative DB system.Object-oriented pattern is used in design and develop process It will be moreconvenient and visual for users

This manual mainly introduces the installation, operation and maintenance ofNC2000 system It includes four parts: Volume I, Introduction of installation processfor NC2000 system, including installation for operation system and configuration forNC2000 Volume II, User operation manual, which detailedly introduce how to useNC2000 system Volume III, Introduction of configuration tools, which introducehow to use system configuration software Volume IV, system maintenance manual,which introduce all the parts need to be maintained, means and steps formaintenance

We hope this manual can help you master our NC2000 system fluently, andkeep the system safe, reliable and stable

This manual includes two parts:

Part I: Installation of operation system It introduces the installation processand steps of relative operation system for NC2000 Nowadays, NC2000 system hassuccessfully run on Windows2000, Red Hat Linux 9 and Sun Solaris 9、10

Part II: Installation of NC2000 system It includes “Installation andConfiguration of NC2000”, ” Installation and Configuration of NARI Oncall”,

“Installation and Configuration of Remote Diagnose Service” It introduces theNC2000 installation process on relative operation system, Project setup andconfiguration, installation and configuration of NARI Oncall and Remote DiagnoseService (RDS)

[Rules]

This manual obeys the following rules:

1 All the titles are in bold face

2 If the title follows by “[Condition]”, It means the contents below this title isrequired under certain conditions

[Notice] User should notice relative issues.

[Warning] User must notice these issues; otherwise it will result in severe

faults

CHAPTER I OVERVIEW 1

CHAPTER 2 INSTALLATION OF OPERATION SYSTEM 2

2.1 Installation of Windows 2000 2

2.1.1 Installation of Windows 2000 2

2.1.2 Windows 2000 Update 11

2.2 Installation of Red Hat Linux 9.0 15

2.2.1 Installation of Red Hat Linux 9.0 15

2.2.2 System Configuration 28

2.2.3 Installation of Java 1.5.0 on Red Hat Linux 9 30

2.3 Installation of Sun Solaris 9 30

2.3.1 Installation of Sun Solaris 9 30

2.3.2 Patch update and configuration for Sun Solaris 9 33

2.3.3 Installation of Java 1.5.0 on Solaris Unix 9 37

2.4 Installation of Sun Solaris 10 37

2.4.1 Preparation before installation 37

2.4.2 Installation steps of Sun Solaris Unix 10 37

CHAPTER 3 INSTALLATION OF NC2000 MONITORING SYSTEM 40

3.1 Installation of NC2000 on Windows 2000 40

3.1.1 Installation process 40

3.1.2 System configuration 40

3.2 Installation of NC2000 on Red Hat Linux 9.0 41

3.2.1 Installation process 41

3.2.2 NARI Auto-start configuration 41

3.3 Installation of NC2000 on Sun Solaris Unix 9.0 44

3.3.1 Installation process 44

3.3.2 System configuration 44

3.4.1 Foundation of NC2000 Web server（C/S） 45

3.4.2 Configuration and Application of NC2000 Web Client（C/S） 52

3.4.3 Installation of NC2000 Web Server（B/S V1.0） 58

CHAPTER 4 PROJECTS CONFIGURATION FOR NC2000 SYSTEM 61

4.1 Projects configuration for NC2000 system 61

4.1.1“NC2000 Configuration” 61

4.1.2 Configuration steps for NC2000 project 62

4.1.3 Example for NC2000 configuration 62

4.2 Directory tree of NC2000 configuration file 63

4.2.1 System file directory: data 63

4.2.2 Project directory: projects.strategy 64

CHAPTER 5 INSTALLATION OF NARI ONCALL SYSTEM 65

5.1 Hardware configuration 65

5.1.1 Computer hardware requirement 65

5.1.2 Telephone pronunciation card 66

5.1.3 GSM Modem 66

5.2 Installation of telephone card driver for NARI Oncall system 66

5.2.1 Driver installation 66

5.2.2 audio card configuration 68

CHAPTER 6 INSTALLATION AND CONFIGURATION OF RDS 70

6.1 Modem installation 70

6.2 Remote server installation 70

6.3 system configuration 72

6.4 Network configuration 75

6.5 Dial server installation 79

Chapter I Overview

NC2000 is automatic monitoring and control software for hydro-powerplants; it is developed by NARI Automation Research Institute, and can run onWindows, Linux, Unix, etc

This manual mainly introduces the installation and configuration process ofrelative operation system and software system It also introduces how to installand configure NC2000 on these platforms

Operation system installation mainly introduces the installation process ofWindows 2000, Red Hat Linux 9.0 and Sun Solaris Unix 9.0 It also introduces theinstallation and configuration process of relative software, for example, JAVA, SunCluster

NC2000 Installation introduces the installation and configuration process ofNC2000 on different operation system (Windows 2000, Red Hat Linux 9.0 and SunSolaris Unix 9.0)

Project Configuration for NC2000 describes how to setup a new project, andbriefly introduces the function of relative configuration files and how to use them NARI Oncall system is one set of Real-time alarm and query system through

by telephone, message or Speech This Chapter introduces its installation andconfiguration process

Using RDS system, engineers can connect and maintain our monitoringsystem thorough remote dial network

Chapter 2 Installation of operation system 2.1 Installation of Windows 2000

 10GB available disk space

 16 bit sound board and speaker

 65,000 color video card ， resolution is 800x600 (mini font) or1024x768（big font）

Recommendatory:

 3.2GHz Intel Pentium IV or coordinate

 80GB available disk space

 16 bit sound board and speaker

 32-bit colorful video card， resolution is 1024x768（big font）

The installation steps on PC are as follows:

1 Insert Win2000 floppy disk, following this screen:

Fig 2-1

2 Select 1, Start Window 2000 professional Installation:

Fig

2-3 Press Enter key and Continue installation:

Fig

2-4 Press F8 key (I agree) to continue

5 Press C key to create disk partitions.

Fig Enter the partition size, and press Enter key to continue

Fig

2-Select NTFS to format the partition, and Press Enter key to continue

Fig

Fig

2-6 After installation is finished, reboot the computer.

Fig 2-9

7 When computer reboots, it will automatically boot into the guide screen

Fig

2-8 Click “Next”.

Fig Click “Next”

Fig

2-9 Enter user name and organization in the appropriate fields and click “Next” tocontinue

Fig

2-10 Enter computer name, password, and Click “Next”

Fig 2-4

Click “Next”

Fig 2-15

11 Click “Next” and continue auto installation

Fig 2-16

2.1.3 Installation of Java 1.5.0 on Win2000

In order to run NC2000 System, you need to install the newest JAVA tool box.This software can be downloaded freely from SUN Website The installation stepsare as following:

 Download the newest JAVA tool box from www.sun.com (for example:jdk-1_5_0_06-windows-i586-p)

 Double click icon file “jdk-1_5_0_06-windows-i586-p.exe”, then pop up thiswindow:

Fig 2-18

Fig 2-19

 Select “I agree”，then click “Next”, pop up this window：

Fig

Fig

2- Click “Finish”, and the installation is finished

2.2 Installation of Red Hat Linux 9.0

2.2.1 Installation of Red Hat Linux 9.0

NC2000 system can run on 32-bit PC, Micro Workstation and Server whichhas installed Red Hat Linux 9.0

The minimum hardware requirements:

 850MHz Intel Pentium III or coordinate

 10GB available disk space

 16 bit sound board and speaker

 65,000 color video card ， resolution is 800x600 (mini font) or1024x768（big font）

The recommendatory hardware requirements:

 3.2GHz Intel Pentium IV or coordinate

 80GB available disk space

 16 bit sound board and speaker

 32-bit colorful video card， resolution is 1024x768（big font）

The installation steps on PC are as follows:

1．Start computer, then insert installation disk labeled with “Setup Disk 1” intofloppy drive Enter “Enter” after “boot:”

Fig 2-26

2． “CD Found”: select “Skip”, then press “Enter”.

Fig 2-27

3． Welcome”: Click “Next”“

Fig 2-28

4 “． Language Selection”：Select “English(English)”，click “Next”

Fig 2-29

5． Keyboard”：Select “U.S English”，Click “Next”“

Fig

2-6． Disk partitioning Setup”: Select “Manually Partition”, Click “Next””

Fig 7．New Partition

Fig

2-8． Boot loader configuration”：Click “Next”“

Fig

2-9 “． Network Configuration”

1)“Hostname”：Select “Manually（M ”） ，enter computer name

2)“Network Device” ： Select “Edit （ E ） ； Cancel “Configure using”DHCP”,Enter “IP address，Netmask”,Click“OK”；Click “Next”

Fig 2-33

10． Error with Data”：Click “Continue”“

Fig 2-34

11 “． Firewall Configuration”：Select “No firewall（O ”） , Click “Next”

Fig 2-35

12． Additional Language Support”：Select “English (USA)”, Click “Next”“

Fig 2-36

13． Time Zone Selection”：Select “Asia/ Karachi”，Click “Next”“

Fig 2-37

14． Set root password”：Enter “Root password，confirm”，Click “Next”“

Fig 2-38

15． Package group selection” ：Select “Server configuration tools” ““ 、 FTPServer”、 Network server” ““ 、 Development tools” “、 Kernel development” “、 Xsoftware development” 、 “ Windows file server” ， Select “single softwaredevelopment”，Click “Next”

Fig 2-40

17 “． About to install”：Click “Next”

Fig 2-41

18． Installing packages”：System begin installing, it will need a quarter “

Fig 2-42

19 “． Congratulations”：Click “Reboot”

Fig 2-43

20 Reboot computer

Fig 2-44

22 “． Date and time”：Enter date and time，Click “Next”

Fig 2-45

23． Display”：Click “Next”“

Fig 2-46

24． Additional CDs”：Click “Next”“

Fig 2-47

25 “． Finish Setup”：Click “Next”

Fig 2-482.2.2 System Configuration

1．Start File Transfer Service “vsftp”, and stop Mail Service “sendmail”

# /sbin/service sendmail stop

2．Start Remote login and copy service ” telnet, rcp, rlogin”

HOSTNAME＝yourhostname

Enter your host name; it will take effect when you reboot the computer

5．Video card configuration

Under GUI or console:

7．MOXA configuration (PCI168H)

1) Copy mxser.tgz to root directory

You can see mxser using lsmod command now

cat file > /dev/ttyM0

The first lamp of MOXA card will light

6) # /etc/rc.sysinit

Add one line after this file:

/sbin/inmod mxser

Notes：First MOXA card: /dev/ttyM0→/dev/ttyM7

Second MOXA card: /dev/ttyM8→/dev/ttyM15

2.2.3 Installation of Java 1.5.0 on Red Hat Linux 9

Jdk-1_5_0_06-linux-i586 patch provided by SUN Corporation is a Java softwarefor computers installed Linux You can freely download it from www.sun.com Theinstallation steps are as follows：

Install JAVA developed patch:

2.3 Installation of Sun Solaris 9

2.3.1 Installation of Sun Solaris 9

NC2000 system can run on 64-bit workstation and server by SUN which hasinstalled Sun Solaris UNIX 9

A．Medium requried：

Solaris 9 Software Two CD

Solaris 9 Language One CD

1、 Select a Language”: Select 6 :Simplified Chinese“

2、 Select a Locale”: Select 0: Simplified Chinese EUC“

3、 Solaris setup program”: Select “Continue”“

4、 Identify system”: Select “Continue”“

5、 Network connect” : Select “Yes”, “Continue”“

6、 DHCP” : Select “No”, “Continue”“

7、 Main network interface”: Select “eri0”,“Continue”“

8、 Computer Name”: Enter computer name, for example: ftop1 ， select“

“Continue”

9、 IP address”: Enter IP address ， for example: 192.9.200.101 ， select“

“Continue”

10、 Subnet”: Select “Yes”, “Continue”“

11、 Network mask”: Enter mask address：255.255.255.0，select “Continue”“

12、 Ipv6”: Select “No”, “Continue”“

13、 Confirm information ”: Select “Continue”“

14、 Configure safety strategy”: Select “No”, “Continue”“

、 Confirm information”: Select “Continue”

19、 Geography Area”: Area: “East Asia” “

Time Zone: “Karachi” and “Continue”

20、 Time and Date”: Enter year, month, day, hour, minute, and select“

“Continue”

21、 Confirm information”: Select “Continue”“

22、 Solaris Interactive setup program”: Select “Initialization” and “Continue”“

23、 Select Area”: Select “Continue”“

24、 Select software”: Select “complete OEM manufacture support and sale”“and “Continue”

25、 Select disk”： Select “Continue”“

26、 Save data”： Select “Continue”“

27、 Automatically format file system”: Select “Manually distribution”“

28、 File and disk forma”: Select “Customize”“

29、 Custom disk”: Manually partition, Unit: MB“

例：0 / 2052

1 swap 2052 （2* Memory size）

2 overlap Whole HD space (no need to modify)

5 /opt 2052

6 /usr 4099

7 /export/home remained space

Select “OK”

30、 file system and disk format”: Select “Continue”“

31、 Install and configure remote file system”: Select “Continue”“

32、 Brief table”: Select “Start”“

If appear “Warning: unused disk space (c0t0d0) , select “OK”

33、Select “Auto reboot”

34、Configure root user and password

35、 Establish Medium”: Select “CD”, “Next” “

36、 Insert CD”：Insert installation disk 2/2, press “Enter”“

38、 Establish Medium”: Select “CD”, click “Next”“

39、 Insert CD”: Insert Solaris 9 Language disk, Select “OK”“

40、 Setup collection”: Select “Continue”“

41、 Establish Medium”: Select “Skip”“

42、 Reboot”: Select “Reboot Now”“

【 Notice 】 You should notice the following points when you install operation system If it needs to install disk array:

“Main network interface”: Select “ce0”:

1 ． Follow the following parameters to do disk partition:

0 / 10240

1 /var 4099 // for system log files

2 overlap 69994 //

3 swap 8192 //2 times of memory

4 /globaldevices 516 // for cluster

5 /opt 4099 // for user exe files

6 /export/home 42800

7 /svm 34 // for disk mirror

2.3.2 Patch update and configuration for Sun Solaris 9

2.3.2.1 System update

Copy file “9_Recommended.zip” to directory “/export/home/nari/software”,Enter command：

/export/home/nari/software> unzip 9_Recommended.zip

Enter command with supervisor：

i) File－Exit

2) Use command line

# groupadd –g 200 narigrp

# useradd –d /export/home/nari –g narigrp –G root –u 268 –s /bin/csh -m nari

# useradd –d /export/home/mysql –g narigrp –G root –u 269 –s /bin/csh -mmysql

2． Modify IP Address

Way 1：

Edit file “ /etc/hosts”，Modify IP Address, and reboot computer

Way 2：

ifcoinfig Device name of network card IP Address

This way can modify IP online, but it will be disabled after computer reboot

3． Configure resolution of double screen

1） When using one video card

（1） Edit file “/usr/dt/config/Xservers”, add the following command after thelast line:

-dev /dev/fb1 -dev /dev/fb2

（2） Configure resolution

# fbconfig -dev /dev/fb1 -res 1280x1024x75 -depth 24

# fbconfig -dev /dev/fb2 -res 1280x1024x75 -depth 24

（3） Enter sync after the above is OK, then reboot computer

2） When using two video cards

（1） Edit file “/usr/dt/config/Xservers”, add the following command after thelast line:

-dev /dev/fb0 -dev /dev/fb3

（2） Configure resolution

# fbconfig -dev /dev/fb0 -res 1280x1024x75 -depth 24