Bsi bs en 03660 010 2010

raising standards worldwide™ NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS EN 3660 010 2010 Aerospace series — Cable outlet accessories for circul[.]

raising standards worldwide™

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

BSI Standards Publication

Aerospace series — Cable outlet accessories for circular and rectangular electrical and optical connectors

Part 010: Cable outlet, style K, straight, shielded, sealed, for heat shrinkable boot

— Product standard

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -This British Standard is the UK implementation of EN 3660-010:2010 The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology

A list of organizations represented on this committee can be obtained on request to its secretary

This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application

© BSI 2010 ISBN 978 0 580 53265 8 ICS 49.060

Compliance with a British Standard cannot confer immunity from legal obligations.

This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2010

Amendments issued since publication

Date Text affected

`,,```,,,,````-`-`,,`,,`,`,,` -NORME EUROPÉENNE

ICS 49.060

English Version

Aerospace series - Cable outlet accessories for circular and rectangular electrical and optical connectors - Part 010: Cable outlet, style K, straight, shielded, sealed, for heat shrinkable

boot - Product standard

Série aérospatiale - Accessoires arrière pour connecteurs

circulaires et rectangulaires électriques et optiques - Partie

010: Raccord, type K, droit, blindé, étanche, pour manchon

thermorétractable - Norme de produit

Luft- und Ramfahrt - Endgehäuse für Elektrische und optische rund- und rechtecksteckverbinder - Teil 010: Endgehäuse, Bauform K, gerade, Ausfürung, Schirmanschluß, abgedichtet, für wärmeschrumpfende

Bauteile - Produktnorm

This European Standard was approved by CEN on 19 May 2010

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member

This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom

EUROPEAN COMMITTEE FOR STANDARDIZATION

C O M I T É E U R O P É E N D E N O R M A L I S A T I O N

E U R O P Ä I S C H E S K O M I T E E FÜ R N O R M U N G

Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2010 CEN All rights of exploitation in any form and by any means reserved

worldwide for CEN national Members

Ref No EN 3660-010:2010: E

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -2

Foreword 3

1 Scope 4

2 Normative references 4

3 Terms and definitions 4

4 Characteristics 4

5 Identification 15

6 Marking 15

7 Technical specification 15

`,,```,,,,````-`-`,,`,,`,`,,` -3

Foreword

This document (EN 3660-010:2010) has been prepared by the Aerospace and Defence Industries Association

of Europe - Standardization (ASD-STAN)

After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn

at the latest by December 2010

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -4

1 Scope

This European Standard defines a range of cable outlets, style K, straight, shielded, sealed for heat shrinkable boots, for use under the following conditions

Associated electrical connector(s) : EN 3660-002

Temperature range Class N : − 65 °C to 200 °C

Class W : − 65 °C to 175 °C

Class K : − 65 °C to 260 °C

2 Normative references

The following referenced documents are indispensable for the application of this document For dated references, only the edition cited applies For undated references, the latest edition of the referenced document (including any amendments) applies

EN 2591-100*, Aerospace series — Elements of electrical and optical connection — Test methods —

Part 100: General

EN 3660-001, Aerospace series — Cable outlet accessories for circular and rectangular electrical and optical

connectors — Part 001: Technical specification

EN 3660-002, Aerospace series — Cable outlet accessories for circular and rectangular electrical and optical

connectors — Part 002: Index of product standards

EN 3660-033, Aerospace series — Cable outlet accessories for circular and rectangular electrical and optical

connectors — Part 033: Band — Product standard 1)

SAE AS85049, Connector accessories, electrical general specification 2)

3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 3660-001 apply

4 Characteristics

4.1 Dimensions and mass

4.1.1 General

For interface dimensions see 4.2

* All parts quoted in this standard

1) In preparation at the date of publication of this standard

2) Published by: Society of Automotive Engineers (SAE), (www.sae.org)

`,,```,,,,````-`-`,,`,,`,`,,` -5

4.1.2 Cable outlet variant A

For screen attachment with banding band, see EN 3660-033

Classes N, W and K

For dimensions and mass, see Figure 1 and Tables 1, 2 and 3

Key

1 Thread A

2 Knurl style, manufacturer’s option

3 Three equally spaced holes for max 0,51 safety wire

4 Manufacturer’s mark and part number

NOTE On both variants, coupling nut to be captive on cable outlet body but free to rotate

Figure 1

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -6

4.1.3 Cable outlet variant B

Screen pre-terminated by manufacturer

Classes N and W only

For dimensions and mass, see Figure 2 and Tables 1, 4 and 5

Key

1 Thread A

2 Manufacturer's mark and part number

3 Knurl style, manufacturer’s option

4 Screen/shield

5 Screen termination device

6 Three equally spaced holes for max 0,51 safety wire

Figure 2

`,,```,,,,````-`-`,,`,,`,`,,` -7

Table 1 — Dimensions common to both variants

Dimensions in millimetres

Shell size

A ∅ B C

Thread — Class 2B

inches − 1,14 0 − 0,56 0

7,75

Table 2 — Maximum cable entry codes and mass for variant A cable outlets

Shell size

Cable entry code

Mass Classes N and W Class K

08 B 7,5 19,5

10 D 9,5 26,0

12 F 11,5 31,0

18 K 16,0 43,5

20 M 21,0 58,0

22 P 23,5 64,5

24 R 26,50 72,5

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -8

Table 3 — Cable entry dimensions for variant A cable outlet

Dimensions in millimetres

Cable entry code

± 0,51 ± 0,51 max

E 11,12 14,30 17,50

F 12,70 15,88 19,05

G 14,30 17,50 20,65

H 15,88 19,05 22,23

J 17,50 20,65 23,80

K 19,05 22,23 25,40

L 20,65 23,83 27,00

M 22,23 25,40 30,16

N 23,83 27,00 31,75

P 25,40 28,58 33,34

R 28,85 31,75 36,51

S 31,75 34,93 42,84

T 34,93 38,10 46,02

Table 4 — Maximum cable entry codes and mass for variant B cable outlet

Shell size

Cable entry code Mass

a

Classes N and W

max max g

08 B 6,5

10 D 8,5

12 F 10,5

14 G 11,75

16 J 13,5

18 K 15,0

20 M 19,5

22 P 21,75

24 R 26,0

28 T 45,5

a The mass quoted includes the device used for securing the screen to the cable outlet plus the specified length of screen and is for the maximum entry size

`,,```,,,,````-`-`,,`,,`,`,,` -9

Table 5 — Cable entry dimensions for variant B cable outlet

Dimensions in millimetres

Cable entry code

∅ D ∅ E

± 0,51 ± 0,51

4.2 Interface dimensions

4.2.1 Associated connection

See EN 3660-002

4.2.2 Standard AS 85049 interface

For classes N and W

See Figure 3 and Table 6

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -10

Key

1 4,95 mm min penetration of Z diameter measured from front of teeth

2 N number of teeth, see Table 6

Figure 3 Table 6 — For standard AS85049 interface

Dimensions in millimetres

Shell size

+ 0,64

0 − 0,38 0 + 0,38

0 − 0,25 0 Number

of teeth

08 12,74 9,14 7,59 6,86 12

12 19,05 15,49 13,94 12,98 21

14 22,23 18,67 17,12 14,86 24

16 25,40 21,84 20,29 18,03 30

18 26,97 23,27 22,07 20,04 33

20 30,18 26,44 25,25 23,22 36

22 33,32 29,62 28,42 26,39 39

24 36,53 32,79 31,60 29,31 42

28 44,45 38,40 37,31 35,28 54

4.2.3 Modified AS85049 interface

For class K only

See Figure 4 and Table 7

`,,```,,,,````-`-`,,`,,`,`,,` -11

Figure 4 Table 7 — For modified AS85049 interface

Dimensions in millimetres

Shell size

Ref + 0,13

0 + 0,18

0 − 0,25 0 Number

of teeth

08 11,10 9,17 6,68 6,86 12

12 17,45 14,83 12,62 12,80 21

14 20,62 17,22 15,98 14,86 24

16 23,80 20,55 17,73 17,93 30

18 25,20 22,48 21,46 20,04 33

20 28,37 25,53 25,02 23,22 36

22 31,55 29,01 27,61 26,39 39

24 34,72 32,46 31,62 29,31 42

28 42,75 38,91 37,97 35,28 54

4.3 Material and finish

Material/finish Class N : Aluminium/electroless nickel plated Material/finish Class W : Aluminium/olive drab cadmium plated Material/finish Class K : Stainless steel/passivated

These descriptions do not apply to EN 3660-033

For screens see Table 11

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -12

4.4 Assembly torque

These torque values are intended for installation use only

Table 8

Shell size

Torque

Nm

± 0,5

08

4,5

10

12

14

16

18

20

9,0

22

24

28 10,0

4.5 Coupling thread strength torques

These torque values are for test purposes, see EN 2591-420 and Table 9

Table 9

Shell size

Torque

Nm

± 0,5

08

5,5

10

12

14

16

18

20

11,0

22

24

28 12,0

`,,```,,,,````-`-`,,`,,`,`,,` -13

4.6 Tests

Test details to be in accordance with Table 10, EN 3660-001 and EN 2591-100

Qualification to be in accordance with EN 3660-001

Table 10

EN 2591- Designation of the test applicable Not Applicable see

EN 3660-001 Details

102 Examination of dimensions

205 Housing (shell) electrical

continuity X Class F: < 2,5 mΩ;

Class W: < 5 mΩ;

Class K: < 10 mΩ

212 Surface transfer impedance

(from 100 MHz to 1 GHz) a X Method 2

Frequency Minimum attenuation Classes F, W and K

301 Endurance at temperature X Classes N and W only

Class K, see b

305 Rapid change of temperature X

Classes

TA TB T1

+ 5

0 − 5 0

N 200 − 65 30

W 175 − 65 30

K 260 − 65 30

continued

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -14

Table 8 (concluded)

EN 2591- Designation of the test applicable Not

Applicable see

EN 3660-001 Details

306 Mould growth X See EN 3660-001, 10.2.3

Class N 48 h Class W 500 h Class K 500 h

Severity: 300

No of shocks:

One in each direction in

3 perpendicular axis Visual examination only

No visual damage

Figure 3 and Table 2 Level J

Duration: 8 hours at ambient temperature

Visual examination only

No visual damage

406 Mechanical endurance — 30 cycles

420 Mechanical strength of rear

accessories X Phase A only Torque as specified in Table 9

513 Magnetic permeability X Not fitted to a connector max

values Classes N and W : 2,0 Class K : 2,5

a 1 GHz to 10 GHz under consideration

b Class K to be subjected to Test EN 2591-301 only where non-metallic components are used

`,,```,,,,````-`-`,,`,,`,`,,` -15

5 Identification

EXAMPLE 1

Description block CABLE OUTLET

Identity block EN3660-010XXXXX

Number of this standard

Material/Finish

For variant B, see Table 11

For variant A, see 4.3

Shell size

Entry size (see Tables 3 and 5)

Screen type for variant B only (see Table 12)

EXAMPLE 2 EN3660-010C08AN Cable outlet, style K, straight, shielded, sealed, aluminium, olive drab cadmium,

cable outlet variant B, shell size 08, entry code A with a pre-terminated nickel plated copper screen

Table 11 — Identification code for material, finish and screen type for variant B only

Code Class a Screen code b

a See 4.3

b See Table 12

Table 12 — Identification code of screen type for variant B only Code Screen and plating

T Tin plated copper

N Nickel plated copper

6 Marking

See Figures 1 and 2 and EN 3660-001

7 Technical specification

See EN 3660-001

Provided by IHS

`,,```,,,,````-`-`,,`,,`,`,,` -and other st `,,```,,,,````-`-`,,`,,`,`,,` -andards-related publications, information `,,```,,,,````-`-`,,`,,`,`,,` -and services

It presents the UK view on standards in Europe and at the international level

raising standards worldwide™

BSI Group Headquarters

389 Chiswick High Road London W4 4AL UK

Tel +44 (0)20 8996 9001

Fax +44 (0)20 8996 7001

www.bsigroup.com/standards

Revisions

British Standards are updated by amendment or revision Users of British

Stan-dards should make sure that they possess the latest amendments or editions.

It is the constant aim of BSI to improve the quality of our products and

serv-ices We would be grateful if anyone finding an inaccuracy or ambiguity while

using this British Standard would inform the Secretary of the technical

com-mittee responsible, the identity of which can be found on the inside front

cover.

Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001

BSI offers Members an individual updating service called PLUS which ensures

that subscribers automatically receive the latest editions of standards.

Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001

Email: plus@bsigroup.com

Buying standards

You may buy PDF and hard copy versions of standards directly using a

credit card from the BSI Shop on the website www.bsigroup.com/shop.

In addition all orders for BSI, international and foreign standards publications

can be addressed to BSI Customer Services.

Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001

Email: orders@bsigroup.com

In response to orders for international standards, it is BSI policy to

supply the BSI implementation of those that have been published

as British Standards, unless otherwise requested.

Information on standards

BSI provides a wide range of information on national, European and international standards through its Knowledge Centre.

Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005 Email: knowledgecentre@bsigroup.com

Various BSI electronic information services are also available which give details on all its products and services

Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: info@bsigroup.com

BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price

of standards For details of these and other benefits contact Membership Ad-ministration

Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: membership@bsigroup.com

Information regarding online access to British Standards via British

Standards Online can be found at www.bsigroup.com/BSOL Further information about BSI is available on the BSI website at www.bsi-group.com/standards

Copyright

Copyright subsists in all BSI publications BSI also holds the copyright,

in the UK, of the publications of the international standardization bodies Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI This does not preclude the free use, in the course of implementing the standard of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission

of BSI must be obtained Details and advice can be obtained from the Copy-right & Licensing Manager.

Tel: +44 (0)20 8996 7070 Email: copyright@bsigroup.com