cisco catalyst 2960 network switch

... Tài liệu đào tạo – Phần B: Cisco Catalyst Switch 4006 và 3524XL Trang 5 Hình 1-2: Catalyst 3524XL switch. Catalyst 3500 series XL switches là một workgroup switch hỗ trợ kết nối Gigabit ... Catalyst3 524_1(config-if)#switchport mode trunk Catalyst3 524_1(config-if)#switchport trunk encapsulation dot1q Catalyst3 524_1#sh interfaces gigabitEthernet 0/1 switchport Name: Gi0/1 Switchport: ... B: Cisco Catalyst Switch 4006 và 3524XL Trang 38 2/2 1-2 Catalyst4 006> (enable) Catalyst3 524_1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Catalyst3 524_1(config)#interface...

Ngày tải lên: 20/12/2013, 22:15

... Medium-Sized Catalyst Switches 107 Catalyst 1900 108 Catalyst 2820 110 Catalyst 2900XL Series 111 Catalyst 3000 Series 113 Catalyst 3900 Series 114 Catalyst 4000 Series 115 Page vii Chapter 6 The Catalyst ... Line Cards 131 Catalyst 8510 Line Cards 132 The Chassis 132 Catalyst 2900 Series 132 Catalyst 5002 Series 133 Catalyst 5000 134 Catalyst 5505 135 Catalyst 5509 135 Catalyst 5500 136 Catalyst 5000 ... thinking that the switch provided all the segmentation necessary. A flat network is a network with little or no logical segmentation. The networks in Figures 1-11 through 1-13 are all flat networks....

Ngày tải lên: 21/12/2013, 04:18

... bytes free) ALSwitch# c. As a precaution, enter the following to disable access to the switch HTML pages: ALSwitch(config)#no ip http server Remove existing html files ALSwitch# delete ... may be needed. b. Re-enable access to the switch HTML pages as follows: ALSwitch(config)#ip http server Step 7 Restart the switch a. Restart the switch using the reload command to see if the ... the Basic Switch Configuration lab. Step 2 Configure the host attached to the switch Configure the host to use the same IP subnet for the address, mask, and default gateway as on the switch. ...

Ngày tải lên: 16/10/2013, 21:15

Ngày tải lên: 20/01/2014, 14:20

Ngày tải lên: 24/01/2014, 10:20

Ngày tải lên: 24/01/2014, 19:20

Ngày tải lên: 24/01/2014, 19:20

Ngày tải lên: 24/01/2014, 19:20

Ngày tải lên: 22/12/2013, 22:17

Ngày tải lên: 17/02/2014, 08:20

... B. • The switch has the address for station B in the MAC address table. © 2002, Cisco Systems, Inc. All rights reserved. 2 Configuring Catalyst Switch Operations Module 3 © 2002, Cisco Systems, ... flooded). © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0—3-14 Summary • Ethernet switches and bridges increase the available bandwidth of a network by creating dedicated network segments ... Layer 2 switching and bridging operations and modes • Describe how LAN switches use and populate the MAC address table © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0—3-4© 2002, Cisco...

Ngày tải lên: 08/07/2013, 01:27

... - CATALYST 2950 SWITCH CONFIGURATION 1. In this lab, you will configure basic IOS commands on switch3 and switch4 which are Catalyst 2950 switches. 2. From the NetSim tool bar, select Switch3 ... Rights Reserved. LAB 13 – VLANs and TRUNKING (Catalyst 2950 Switches) 1. In this lab, you will set up VLANs on switch3 and switch4 (Catalyst 2950 switches) and test them by pinging between router3 ... Reserved. LAB 11 – VLANS and TRUNKING (Catalyst 1900 Switches) 5a. Question: what VTP operating mode are the switches in? • Answer: the Catalyst 1900 switch defaults to ‘server’ mode. 6a....

Ngày tải lên: 29/09/2013, 22:20

... (Model) 640-604 Switching 3.0 www.testking.com - 19 - Switching 3.0 (Building Cisco Multilayer Switched Networks) Exam Code: 640-604 Certifications: Cisco Certified Network Professional ... sublayer) Metropolitan-Area Network Message Digest Algorithm 5 Multilayer Switching Multilayer Switching Route Processor Multilayer Switching Switch Engine Multilayer Switching Protocol Multicast ... information, the switch will not be able to produce wire-speed results. 1.4.1.5 Multi-Layer Switching (MLS) Multi-layer switching combines layer 2 switching, layer 3 switching, and layer 4 switching...

Ngày tải lên: 16/10/2013, 13:15