Tài liệu Fiber Frames ppt

6/04 ADC’s Fiber Frame Products • Provide a centralized point for: - Termination - Splice - Jumper storage - Passive optical components • Reduce maintenance costs • Assure increased subs

Introduction 106

6/04

ADC’s Fiber Frame Products

• Provide a centralized point for:

- Termination

- Splice

- Jumper storage

- Passive optical components

• Reduce maintenance costs

• Assure increased subscriber retention

• Prevent fiber congestion

• Physical fiber protection

• Widest choice of frame solutions

Fiber Distribution Frames

• Patented individual angled left/right adapters

eliminate 90 degree bends of optical patch cords

• Clear cable routing paths

• Integrated bend radius protection

• Front and rear access or all front access options

• Quick and easy circuit restoration due to superior

patch cord storage options

• Allows integration of advanced optical components

for capacity/service upgrades and local testing

• Dedicated splice bay options available for off-frame splicing:

ADC recommends this option for greater flexibility, more

cost-effective use of office space and reduced time and cost

for installation and maintenance

6/04

Next Generation Frame Products

• Unmatched termination density

• Easy access to connectors and patch cords

within a fully loaded frame

• Clear cable routing paths

• Integrated bend radius protection

• Equipment bays for mounting 19" and 23"

equipment within the NGF lineup

• Integrated jumper storage promotes quick and

easy circuit restoration

• Allows integration of advanced optical components

for capacity/service upgrades and local testing

• 600mm x 300mm footprint

• 10 module mounting positions

• Total front-access frame

• Allows integration of advanced optical

components for capacity/service upgrades

and local testing

• Shipped with lockable front doors

• Dedicated splice bay options available for

off-frame splicing: ADC recommends this

option for greater flexibility, more cost-effective

use of office space and reduced time and cost

for installation and maintenance

• OMX Interbay Management Panel

- Off-frame jumper slack storage

- Bend radius protection

- 150mm x 300mmIntroduction

Main Components of the Front Load FDF

Front Load fiber frames can be ordered and shipped as a single unit Simply specify the required

components and ADC will assemble the frame for you Certain items must be ordered as separate lineitems and shipped separately for on-site installation; these items are indicated below

How To Order a Front Load Frame

Select the desired bay based on height

Select the desired Front Load modules

Connector Modules: Available in 72 position, 96 position and a 12-pack plug-in configuration The

72 position module is recommended for most applications Also available in 144 position using ADC’s

Splice Modules: Accommodate splicing for connector modules (Remember that splice trays and cable

clamps must be ordered separately.)

Storage Modules: Used to store jumpers when 5" bay spacing is not available (storage modules are not

mandatory when the interbay management panel is used).

Value-Added Modules (VAM): 12 position VAM chassis available for Front Load frames The Front Load

VAM chassis holds up to 12 single VAM plug-ins.

NOTE: Rear Load modules cannot be installed into a Front Load bay.

Metal doors

Upper and lower half bay doors are recommended to protect fibers on the rear side of the bay.

Interbay management panels (ordered and shipped as separate line items)

The interbay management panel mounts between bays in the same manner as a 5" (12.7 cm) bay spacer

This panel is optional but is recommended for all applications of the frame An interbay panel should be

mounted on each side of a fiber frame For underfloor cabling/raised floor applications an underfloor guard box is required.

Optional Equipment

Rear fiber storage panel (cross-connect applications only)

Provides cable management and service loop storage of fiber optic patch cords which are typically routed between an ADC fiber distribution frame (FDF) and the fiber optic terminal (FOT) equipment Cannot be used on OSP bays where cable clamps are used

End guards (ordered and shipped as separate line item).

As necessary for vacant positions.

Cable clamps (ordered and shipped as separate line item)

One cable clamp is required for each cable brought into the frame.

Communication panels

If a communication panel is desired, it will occupy one module location in the bay.

Fiber optic patch cords

6/04

Configuration and Order Form

This page may be copied and used to configure a Front Load frame The configuration drawing may then

be attached to an order

Front Load frames include front vertical cable guides and rear fanning triangles Interbay management panels and end guards shown here are ordered separately Write catalog numbers for modules in each location on drawing

*14" lower troughs are recommended for most applications; however, other lower troughs are available Contact ADC’s Technical Assistance Center at 1-800-366-3891

1 5 10 15 20 25 30 35

Catalog Number Quantity

Front Load Frames

6/04

Front Load Fiber Distribution Frame with 14" (35.56 cm) Trough

2.00"

7.00'

1 5 10 15 20 25 30 35 39

14" HORIZ CABLE TROUGH

(12) CABLE TIE BRACKETS (INCLUDED

2"

GUARD BOX

5.00"

5.00"

7' INTERBAY MANAGEMENT PANEL E-501-L139 (2) 7' END GUARD

UEGP-7PW (2)

Front Load FDF E-501-L88

1 5 10 15 20 25 30 35 39

GROUND LUG WITH #6 COPPER WIRE TINNED 75" REAR

25.88"

FANNING TRIANGLES (INCLUDED WITH FDF)

Recommended Bay Style

Front View*

• Used in cross-connect or interconnect applications when splicing is done within the frame

• Modules attach to front vertical cable guides

• Only ADC Front Load FDF modules can be used in this bay

• Rear Load modules cannot be installed into a Front Load bay

• Up to eight 8" (20.32 cm) modules can be installed in one Front Load bay

• 7' (2.14 m) bay supports up to 1152 terminations

• Front Load FDFs include unequal flange network type (4.5" guard box) rack, 14" lower horizontal cable trough, front vertical cable guides, rear fanning triangles, ground wire kit and cable tie brackets

Description

Network Style Unequal Flange Front

Load Bay with 14" (35.56 cm) Trough

(3.52 m x 66.04 cm x 30.48 cm)

1 These products are available in black; add “-B” to the end of the catalog number.

*Interbay management panels and end guards shown are for reference only They are ordered separately.

For Use on Front Load Frames Only

Half Bay Metal Doors

The upper and lower half bay doors completely

cover the rear of the bay Constructed of metal,

these doors are hinged on both sides and latch

securely, protecting fiber from damage and snags

8" (20.32 cm) Metal Doors

Individual metal doors are available for the rear of

the bay Six inch doors are designed for the upper

and lower most positions on the bay Eight inch

doors are designed for the back of the various

modules within the bay Constructed of metal,

these doors are hinged on both sides and latch

securely to protect fibers on the rear of the bay

To provide individual doors for the entire bay, two

6" doors and eight 8" doors are needed

8" metal doors are standard on Rear Load modules.

Order only for Front Load frames.

TOP HALF DOOR KIT

BOTTOM HALF DOOR KIT

39 35 30 25 20 15 10 5 1

DETAIL A

6" DOOR KIT

DOOR ASSY SEE DETAIL A

8" DOOR KITS

6" DOOR KIT

39 35 30 25 20 15 10 5 1

FRAME

FANNING TRIANGLE

Description

Half bay metal doors

Mount into Front Load frames or

WECO hole spaced racks only

Upper half bay

Lower half bay

Individual module metal door

Mount into Front Load frames or

WECO hole spaced racks only

6" top or bottom of bay

8" module

E-501-L157 E-501-L156

E-501-L154 E-501-L155

O r d e r i n g I n f o r m a t i o n

Dimensions (HxW)

38" x 23" (96.52 x 58.42 cm) 38" x 23" (96.52 x 58.42 cm)

6" x 23" (15.24 x 58.42 cm) 8" x 23" (20.32 x 58.42 cm)

1 These products are available in black; add “-B” to the end of the catalog number.

Front Load Frame Hardware

6/04

Connector Module — 72, 96 or 144 Termination

• The patented angle retainer allows removal of the adapter from the front of the module without the use of tools providing access to the connector on the inside of the panel for cleaning

• Fanning strips maintain 1.5" (3.81 cm) bend radius, provide organization, hold fibers in place at point of entry to the module

• Removable transparent, smoked plastic cover encloses front of module; protects fibers and

connectors from disturbance

• Designation card, identifying each cable, is visible when cover is opened or closed

• An accessory mounting kit is required when installing a Front Load module into a plain, 23" WECO drilled, unequal flange rack (Non-ADC Front Load Frame)

• 72 position connector modules are numbered 1-36 on the left, 37-72 on the right 96 position connector modules are numbered 1-48 on the left, 49-96 on the right Standard modules are numbered vertically (see Figure 1) Horizontally numbered connector modules are also available

Singlemode Adapter Type

6/04

The pigtails have an overall protective jacket with 12 color-coded 900µm stranded fibers inside Each 12-fiber pigtail bundle is numbered making it easy to identify each bundle and route them to the desiredsplice tray They are over 5 meters long so they can be routed from any connector module to the splicemodule within the frame

Singlemode Connector Type

36 37

42 56

72

2 34 5 6 1

8 49

56

Front Load Frame Modules with Pigtails

1 These products are available in black; add “-B” to the end of the catalog number.

Fiber Pigtail Assemblies

Fiber pigtail assemblies are used within a frame and typically

routed from the backside of a connector module to the splice

module where they are spliced to OSP fibers ADC offers 5 meter

stranded pigtail assemblies that consist of 12 color-coded 900µm

fibers covered in an overall jacket referred to as a soft wall

bundle The flexible jacket provides physical protection for the

individual fibers as they are routed from the connector module

to the splice module

Buffered Fiber

900 micron

PVC Jacket 0.64 mm thick

Soft Wall (12 Fiber Shown)

6/04

Front Load Splice Module

Description

Splice module with eight (8) drawers

For Front Load Frames

Cable clamp (0.4" - 1.2" O.D.)

10.00"

4.94"

Top View Front Load Splice Module Loaded with Pigtails

Front Load Splice Module E-501-L33

• Maximum capacity of 192 splices with stranded fiber, 384 splices with ribbon fiber using ADC’s new moisture blocking kit for IFC and OSP ribbon fibers

• Each splice drawer holds two single or one dual splice tray

• Splice trays are available with heat shrink fusion, bare fusion or mechanical (Elastomeric)/mass fusion

• Each drawer designed to handle twenty-four 900 micron pigtails or twelve 3 mm pigtails

• Cover encloses the splice module for protection from normal frame activity

• Pigtail and OSP buffer tubes enter and exit through openings on the back of the module

• Patented slack take-up wheel keeps constant tension on the fiber cable and prevents binding when drawer is closed

• Cable clamps must be ordered separately and attach to the rear cable management of the frame

1 These products are available in black; add “-B” to the end of the catalog number.

6/04

Rear Load Frames

How To Order A Rear Load Frame

When fiber products are ordered with a factory terminated intrafacility fiber cable (IFC), they must beordered as individual line items and shipped separately from the bay Other modules specified can beassembled with the bay

Rear Load bays are typically used in cross-connect applications in which splicing is done in the vault or adesignated off-frame splice area

Main Components of the Rear Load FDF

Select the desired bay based on height

Select the desired Rear Load modules

Connector Modules: Available in 72, 96, 144 position and a 12-pack plug-in configuration These

modules can be ordered loaded with adapters only or with pre-terminated IFC The 72 position module

is recommended for most applications Connector modules with IFC can be ordered with IFC oriented for underfloor routing

Storage Modules: Used to store jumpers when 5" bay spacing is not available (storage modules are not

mandatory when the interbay management panel is used)

Value-Added Modules (VAM): 12 position VAMs are available for Rear Load style frames and house

VAM plug-ins The Rear Load style VAM chassis holds up to 12 single VAM plug-ins

All Rear Load style modules come standard with 8" (20.32 cm) rear doors and rear cable management attached at the factory.

NOTE: For applications in which splicing will be done in the FDF, Front Load frames are recommended

Interbay management panels (ordered and shipped as separate line items)

The interbay management panel mounts between bays in the same manner as a 5" (12.7 cm) bay spacer

This panel is optional but is recommended for all applications of the frame An interbay panel should

be mounted on each side of a fiber frame For underfloor cabling/raised floor applications, an underfloor guard box is required.

Optional Equipment

End guards (ordered and shipped as separate line item).

Blank panels

As necessary for unused positions.

Cable clamps (ordered and shipped as separate line item)

One cable clamp is required for each multifiber cable brought into the bay Rear Load connector modules with IFC include a cable clamp.

Communication panels

If a communication panel is desired, it will occupy one module location in the bay.

Fiber optic patch cords.

1

6/04

Configuration and Order Form

This page may be copied and used to configure a Rear Load frame The configuration drawing may then beattached to an order

Interbay management panels and end guardsshown here are ordered and shipped separately.Write the catalog numbers for the modules ineach location on the drawing

Pre-terminated Rear Load modules are shippedseparately from the bay

14" lower troughs are recommended for mostapplications; however, other lower troughs are available

1 5 10 15 20 25 30 35

Fiber optic patch cords

Write catalog number in each location on drawing above

Order on separate form Order on separate form

Catalog Number Quantity

Special Configuration Instructions

(Example: AC outlet)

6/04

Rear Load Fiber Distribution Frame with 14" (35.56 cm) Trough

2.00"

7.00'

1 5 10 15 20 25 30 35 39

4.50"

8 7 6 5 4 3 2 1

14" HORIZ CABLE TROUGH

(12) CABLE TIE BRACKETS (INCLUDED WITH FDF)

2"

GUARD BOX 5.00"

5.00"

7' INTERBAY MANAGEMENT PANEL E-501-L139 (2) 7' END GUARD

UEGP-7PW (2)

REAR LOAD FDF E-501-L91

1 5 10 15 20 25 30 35 39

GROUND LUG WITH #6 COPPER WIRE TINNED 75" REAR

25.88"

25.88"

2.5"

Recommended Bay Style

* Interbay management panels and end guards shown are for reference only They are ordered separately.

• Rear Load bays are recommended for applications when splicing is done in the vault or at an off-frame splice area

• Up to eight 8" (20.31 cm) modules can be installed in one Rear Load bay

• 7' (2.14 m) bay supports up to 1152 terminations

• Rear Load FDFs include unequal flange network type (4.5" guard box) rack, 14" lower horizontal cable trough, front vertical cable guides, ground wire kit and cable tie brackets

• All Rear Load modules are equipped with rear fanning triangles and 8" (20.32 cm) rear doors

Description

Network Style Unequal Flange Rear

Load Bay with 14" (35.56 cm) Trough

6/04

Connector Module — 72 or 96 Termination

• All Rear Load modules come with rear doors and cable management attached

• Patented angled retainers designed for easy removal without use of tool; allows easy access to back

of the adapter/receptacle from front of bay

• Fanning strips maintain 1.5" (3.81 cm) bend radius, provide organization, hold fibers in place at

point of entry to the module

• Removable transparent, smoked plastic cover encloses front of module; protects fibers and connectors from disturbance

• An accessory mounting kit is required when installing a Rear Load module into a plain, 23" WECO drilled, unequal flange rack (Non-ADC Front Load Frame)

Singlemode Adapter Type

6/04

Rear Load Frame Connector Modules

Connector Module Equipped with Singlemode IFC

• Modules with IFC attached ship as a single unit with cable clamp installed

• Modules completely loaded with adapters, even when partially loaded

with IFC

• Two ordering options:

- Standard spool: module mounted to rack before IFC is uncoiled

- Modified spool: module attached to spool and rotated as the IFC is uncoiled from the spool The modified spool works best when a pipe

is slid through the middle of the spool for use as an unwinding feature

Catalog Number FCM- / -

Module Type Spool Type

Q FC angled polish, zirconia sleeve

K LC ultra polish

* Modules using ADC’s house cable have a shorter

lead time than modules using a specific cable

manufacture ADC only provides GR-409

compliant cable that meets or exceeds our high

quality standards House cable vendors include

Alcatel, Corning, and Pirelli.

When selecting ADC’s house cable, the module

type must be either 8, 9 or E The module will

then be packaged in ADC’s new protected spool

where the module is shipped inside the spool for

added protection.

Cable Type

Special Configurations

Putty, cable exits up

raised floor installation

raised floor installation

Length in Meters

+

+ +

leave blank

6/04

Rear Load Splice Module

• Both outside plant (OSP) and fiber optic terminal (FOT) patch cords are terminated at the rear of the FDF, making them less vulnerable during routine maintenance performed on the front of the FDF.

• Each splice drawer holds two 12 fiber (single) or one 24 fiber (dual) splice tray

• Splice trays are available with hear shrink fusion, bare fusion or mechanical (Elastomeric)/mass fusion

• Each drawer designed to handle twenty-four 900 micron pigtails or twelve 3 mm pigtails

• Cover encloses the splice module for protection from normal frame activity

• Pigtail and OSP buffer tubes enter and exit through openings on the back of the module

• Patented splice tray with slack take-up wheel keeps constant tension on the fiber cable, prevents binding when drawer is closed

• Cable clamps must be ordered separately

Description

Splice module with either (8) drawers

For Rear Load frames

Cable clamp (0.4" - 1.2" O.D.)

6/04

Front and Rear Load Frame Accessories

Heat shrink fusion

24 Position Splice Trays

192 192 192

192

192 192 192

Number of Splice Trays per Drawer

2 2 2

2

1 1 1

Number of Splices per Tray

12 12 12

18*

24 24 24

Catalog Number

FST-FT FST-HS FST-MT

FST-HS-3

FST-D-FT FST-D-HS FST-D-MT

O r d e r i n g I n f o r m a t i o n

* Used with 8 fiber soft-wall bundled pigtail assembly, maximum 32 fibers per drawer

Other splice types are available Please contact ADC.

6/04

Rack Installation Kits

FRONT OF FRAME REF

FRONT OF FRAME REF

1.81" (2)

4.81"

(3) 7.82" (2)

4.31" (4) 5.16" (2)

5.38"

2.69"

3.0" 3.0"

5/8"-11 WELD NUT (3) OPPOSITE SIDE

7' TOP MOUNTING DETAIL

8', 9' & 11'6" TOP MOUNTING DETAIL

0.78 (2) ON 23"

RACKS ONLY

BOTTOM VIEW BASE MOUNTING DETAIL 7', 8', 9', 11'6"

25.875"

0.495" HALF SHEAR FORM TO NEAR SIDE 4X (KNOCKOUT)

TOP VIEW BASE MOUNTING DETAIL 7', 8', 9', 11'6"

9.625"

TOP ANGLE IRON

2 X 2

2" GUARD BOX HAS BEEN REMOVED FOR CLARITY

45 ° (4)

3.0" 3.0"

Network Type Unequal Flange Rack Mounting Details

Relay Rack Base Relay Rack

Raised Floor

1

Wedge (4) with Anchor Kit

Washer (4) with Anchor Kit

Hex nut, Torque (4) with Anchor Kit

Stud (4) with Anchor Kit

Underfloor Mounting Kit

6/04

Front and Rear Load Frame Hardware

Rack Installation Kits

Description

Rack installation kit for 7' racks, includes:

- (1) floor mounting kit

- (1) top attachment kit for 7' racks

- (12) rack tie brackets kits

- (1) rack ground kit for 7' racks

Rack installation kit for 9' and 11' 6" racks, includes:

- (1) floor mounting kit

- (1) top attachment kit for 9' and 11' 6" racks

- (22) rack tie brackets kits

- (1) rack ground kit for 9' and 11' 6" racks

Universal anchor kit, for all UEF Racks includes:

- (4) anchor assemblies

- (2) universal hold down bars

- (8) anchor plate washers

- (8) shim plates 063

- (4) shim plates 125

5/8" Raised Floor Mounting Kit

- (4) threaded rods 5/8" - 11"x 12"

- (12) heavy nuts, locks and flat washers

- (4) nuts with springs 1/2"x 13", and shoulder washers

- (1) 10' unistrut and anchor kit

5/8" Raised Floor Mounting Kit

- (4) threaded rods 5/8" - 11"x 30"

- (12) heavy nuts, locks and flat washers

- (4) nuts with springs 5/8"x 11", and shoulder washers

- (1) 10' unistrut

- (1) RINST-FLR universal anchor kit

1/2" Raised Floor Mounting Kit, 30" Threaded Rod

- (4) threaded rods 1/2" - 13" x 30"

- (12) heavy nuts, locks and flat washers

- (4) nuts with springs 1/2"x13", and shoulder washers

- (1) 10' unistrut and anchor kit

1/2" Raised Floor Mounting Kit, 42" Threaded Rod

- (4) threaded rods 1/2" - 13" x 42"

- (12) heavy nuts, locks and flat washers

- (4) nuts with springs 1/2"x 13", and shoulder washers

- (1) 10' unistrut and anchor kit

6/04

Interbay Management Panel

Description

Universal interbay management panel

Includes trough filler insert and lower

• Provides storage between the bay

for patch cords

• Available for 7', 9' or 11.5' (2.14,

2.75, 3.51 m) bays

• 5" trough filler insert protects the

fiber in the lower trough between bays

• Includes a lower guard box and 5"

trough filler insert

• To provide space for these panels,

all bays must be spaced 5"

(12.7 cm) apart

See following page for information on

underfloor guard boxes.

Optional retrofit cover kits are available for 14" lower troughs.

For existing lineups with 6", 8" or 16" lower cable troughs, call ADC Technical Assistance Center, 1-800-366-3891.

1 These products are available in black; add “-B” to the end of the catalog number.

6/04

Front and Rear Load Frame Hardware

1 These products are available in black; add “-B” to the end of the catalog number.

Guard Boxes – Underfloor

Description

Underfloor guard boxes

Rear access only Used for routing OSP

or IFC cable or patch cords from under

floor to the rear of the bay.

Front and rear access Used for routing

OSP, IFC or patch cords from under floor

to the rear of the bay and patch cords

from under floor to the front of the bay.

FDF-ACC152 Shown Installed Between Network Racks and at end of lineup (Front View)

FDF-ACC152 Front/Rear Access Underfloor Guard Box (Rear View)

6/04

1 These products are available in black; add “-B” to the end of the

catalog number.

Rear Fiber Storage Panel

Description

Rear fiber distribution frame storage panel kit

Includes one storage panel, with spools and

mounting hardware

FDF-RFSP

O r d e r i n g I n f o r m a t i o n

• Provides cable management and service loop storage of fiber optic

patch cords typically routed between an ADC fiber distribution frame (FDF) and the fiber optic terminal (FOT) equipment

• Kit contains one storage panel with spools and mounting

hardware to secure the panel to the frame

• Can be installed in existing lineups

• Mounts on either left or right duct area of FDF

• Attaches to 7', 9' or 11.5' frames

• ADC recommends storing excess patch cord slack at the FOT to

distribute the slack to multiple locations throughout the central office/headend

• Cannot be mounted onto the frame if any cable clamps are

present on that side of the frame

End Guards

• Attaches to either a bay or interbay management panel

• Serves as a mounting place for outlets and switches

• Used interchangeably for either left or right applications

• Provides protection and a finished appearance at the start

and end of bay lineups

12"

D 2.5" W

H

Description

Network bay end guard panel

Mounts on IMP or bay

2.5" W (6.35 cm) and:

7' H (2.14 m) x 12" D 9' H (2.75 m) x 12" D 11.5' H (3.51 m) x 12" D

UEGP-7PW UEGP-9PW UEGP-115PW

O r d e r i n g I n f o r m a t i o n

6/04

1 These products are available in black; add “-B” to the end of

the catalog number.

Accessories

Horizontal Cable Troughs

Lower horizontal cable troughs are always

included with fiber bays They can be

purchased separately for special applications

The upper cable trough is not a standard part

of the bay It should be used in applications in

which patch cords need to be brought from the

front of the frame to the rear The upper cable

trough is putty white and mounts at the top of

the bay Bend radius limiters are provided on

the edges of the trough to maintain minimum

bend radius requirements 14" Lower Cable Trough

O r d e r i n g I n f o r m a t i o n

Description

Cover for 14" (33.56 cm) lower horizontal

cable trough; requires modified lower

horizontal cable troughs

FILLER TROUGH

FRAME

INTERBAY MANAGEMENT PANEL

(Optional cover for interbay manage- ment panel See page 16 for ordering information)

Grounding Kit Accessories

12.24" X 1/2"

Screw Wire Clip

2 Hole Lug

12.24" x 1/2" Screw Copper Wire Tinned Central Office

H-Tap

6 AWG Stranded Wire

6 AWG Solid Wire

Fiber Frame (Rear)

Wire Clip Mounting

Description

FDF grounding wire kit*

H-TAP bonding kit Grounding kit, channel racks

Catalog Number

E-501-L37 E-501-L166 GAK

O r d e r i n g I n f o r m a t i o n

* Included with ADC Fiber Frame

Each kit includes the following:

FDF ground wire kit (included with all frames)

H-TAP bonding kit

GAK grounding kit

Rack Filler Plates

Rack filler plates are recommended for use between

the splice frame and adjacent bays or end guards

The rack filler plates are putty white and come with

O r d e r i n g I n f o r m a t i o n

5" (WIDTH) 12"

(DEPTH)

7' (HEIGHT)

AC Outlet Kit and Raceways

End View Cap Fitted

BK

W

GN Hole for

AC Supply Access

Prewired 3-Wire Duplex Receptacle

Description

AC outlet kit – 25.84" (65.63 cm)

AC raceway

25.84" (65.63 cm) – used for bays which do not require AC power

5.0" (12.7 cm) – used with AC outlet kit when bays are spaced 5.0" (12.7 cm)

ACOK-PWNB ACB-PWNB AC-PWNB-RS5*

O r d e r i n g I n f o r m a t i o n

6/04

Cable Clamps and Dual Cable Clamp Plate Kit

The cable clamp kits provide a means of securing the end of an outside plant (OSP) or intrafacility cable

to the cable plate Cable diameters must be between 0.4" and 1.2" (1.02 to 3.05 cm) Additionalcomponents are included with the OSP clamp kit for grounding metallic parts of the cable such asmetallic strength members or metallic sheaths

OSP CABLE

EXISTING REAR CABLE MANAGEMENT PLATE

GROMMET 10-32 NUT

CLAMP COVER COVER PLATE 6.32 x 375 SCREWS CLAMP BRACKET

CABLE CLAMP PLATE MOUNTING

6.32 x 250 SCREWS

CABLE CLAMP COVER NUTS (4)

Description

Cable clamp kit

For IFC and outside plant cable

Dual cable clamp plate kit

doubles the number of clamping

positions on the frame from 32 to

64; kit includes plate only

There are times when a single module must be mounted in a bay without a cable management system.

An individual 8" mounting kit is available to mount FDF modules into certain rack types The E-501-L347kit includes the rear fanning triangles and front vertical cable guides An 8" H (20.32 cm) door can beadded separately

Description

Rear Load Module Kit

Contains two 8" front vertical cable guides and screws

Front Load Module Kit

Contains two front vertical cable guides, 8" section of rear cable management

and required mounting screws

FDF-ACC145 E-501-L347

Designation label kits (front and rear)

With (2) 4" x 10" cards – for 96 termination modules ordered prior to 11/93

With (1) 4" x 18" cards – for 96 termination modules ordered after 11/93

Retrofit kit with clips – converts E-501-L69 to E-501-218

Catalog Number

E-501-L69 E-501-L218 E-501-L219

O r d e r i n g I n f o r m a t i o n

Designation Labels

6/04

Features and Benefits

Ample Trough Space

Reduces jumper pile-up and congestion

- Reduces maintenance time due to easy removal and tracing of jumpers

- Minimizes risk of microbends or damage to fiber

Built-in Jumper Storage Panel

Minimizes number of required jumper lengths

Maintains fiber bend radius

Simplifies frame installation

- Saves money by reducing the number of different jumper lengths that have to be kept

in inventory

- Minimizes risk of microbends or damage to fiber

Sliding Adapter Packs

Promotes high density

Provides easy access to connectors

- Saves valuable floor space

- Reduces time required for operations and maintenance

Intelligent Cable Routing System

No fiber cross-over points

Multiple vertical troughways

- Reduces maintenance time due to easier removal and tracing of jumpers and minimizes fiber “weaving”

Bend Radius Protection at Every Turn

- NGF provides complete bend radius at every turn to ensure network performance and reliability

Frames

ADC’s Next Generation Frame product line has fiber frames designed to fit a variety of termination, splice,and storage applications Each frame option is designed with an emphasis on superior cable managementand ease of use, including features such as ample trough space for cable and jumpers, easy access toconnectors, and storage for jumpers The frame sections are shipped from the factory fully equipped withall cable management hardware including a built-in jumper storage panel

Fiber Termination Blocks (FTB)

Fiber Termination Blocks (FTBs) are available with SC and FC adapters in block configurations of 48, 72, 96

or 144 positions Also, a 144 position FTB is available using LX.5®or LC adapters FTBs utilize sliding adapterpacks to gain easy access to both the front and rear connectors There is also a block configuration available

to accommodate Mini Value-Added Modules (Mini VAMs) for applications requiring splitters or WDMs FTBscan be ordered with adapters only or with factory terminated IFC or outside plant cable

Fiber Combination Blocks (FCB)

Fiber Combination Blocks (FCBs) provide termination and on-frame splicing capabilities, all in one block The block occupies two mounting positions on the frame section They are available with SC and FCadapters in block configurations of 48, 72, 96 or 144 positions Also, an FCB with 144 positions is available using LX.5®or LC adapters

6/04

Important Facts on Trough Space

Horizontal Trough Space

10"

(5"Upper and Lower) 3,680

FMDF:

864 Fiber Terminations

Conventional Frame:

648 Fiber Terminations

LGX Style High Density:

1152 Fiber Terminations

Horizontal Trough Space

10"

(5"Upper and Lower 8,240

FMDF:

1728 Fiber Terminations

Conventional Frame:

648 Fiber Terminations

LGX Style High Density:

1152 Fiber Terminations

Selecting an FMDF, F3MDF or Slim Rack System

6/04

The FMDF is the cornerstone of the NGF product line This innovative frame has six 5 inch horizontal troughs for a total of 30 inches of horizontal trough space This abundant trough space minimizes fiber pile up and congestion leading to easier jumper traceability and removal The frame has twelve FiberTermination Block (FTB) mounting positions equally divided between vertical columns on the left and right sides of the frame as shown in the figure below This frame provides additional vertical trough space for the highest termination density applications and is highly recommended when the density on

a single frame exceeds 864 terminations The built-in jumper storage panel will store up to 3.5 meters (12 feet) of jumper slack

Jumper Storage Panel

Left Vertical

Right Vertical Horizontal

Trough(6)

FTB Mounting Position (12)

6/04

Front Facing Fiber Main Distributing Frame (F3MDF)

The F3MDF is designed for single-sided access applications and may be mounted up against a wall or back-to-back to save floor space Unlike the FMDF, the more compact F3MDF is equipped with a single

9 inch horizontal trough on the front The F3MDF has twelve FTB mounting positions equally dividedbetween vertical columns on the left and right sides of the frame as shown in the figure below The 30inch wide frame provides additional vertical trough space for the highest termination density applicationsand is highly recommended when the density on a single frame exceeds 864 terminations The built-injumper storage panel will store up to 3.5 meters (12 feet) of jumper slack

Jumper Storage Panel

Left Vertical

Right Vertical

FTB Mounting Position (12)

Front Horizontal Trough 7'

- 30" wide F3MDF is recommended for use with the 96 position Fiber Termination Blocks and is required when using 144 position FTBs

- Each frame section includes heavy duty floor anchor bolts for concrete floor applications.

(2.14 m x 76.2 cm x 48.26 cm)

O r d e r i n g I n f o r m a t i o n

6/04

The Fiber Slim Rack is designed for lower density applications than the FMDF or F3MDF It has six FTBmounting positions and is designed for single-sided access applications The Slim Rack is intended for use

in a single frame application and should not be used in a multiframe lineup The built-in jumper storagepanel will store up to 3.5 meters (12 feet) of jumper slack

When ordering FTBs for the Slim Rack, remember that only LEFT oriented blocks are used on this frame.

FTB Mounting Position

Jumper Storage Panel

Each frame section includes heavy duty anchor bolts for concrete floor applications.

Not rated for Zone 4 applications.

Side View

7'

Maximum Termination Capacity

576

Fiber Termination Blocks (FTB) – Unterminated (Adapter Only)

FTBs without fiber can be ordered fully loaded with

adapters Before ordering, determine the block

orientation and cable exit direction Unterminated

FTBs may be ordered with a “left” orientation

(mounts on the left side of the frame) or a “right”

orientation (mounts on the right side of the frame)

The cable exit direction will be either “upward”

(cables terminated to the rear side of the block exit

up toward the top of the frame) or “downward”

(cables terminated to the rear side of the block exit

down toward the bottom of the frame) All blocks

with adapters only are configured to terminate

single or dual jumpers on the rear of the block If a

multifiber breakout style cable (i.e., OSP/IFC) is to

be terminated to the rear of the block, a separate

clamping kit and replacement rear storage area kit

is required (See next page.)

Adapter Type Singlemode

7L2QXK

Block Style

124

1

2

4

5 3

UpwardDownward

Block Configuration

ABCM

487296144*

Block Orientation

LR

LeftRight

* 144 blocks cannot be used in

26" wide NGF frames

144-Position Right Upward FTB Shown

* When using the FOTSB slack storage panels, a UP

block must be used.

6/04

Adapter-only blocks ordered from page 7 are configured to accommodate single fiber jumpers or multifiberbreakout cables If loading a pre-terminated intrafacility (IFC) cable or a pre-terminated OSP cable is

desired, additional hardware will be required Block conversion kits are available to convert adapter onlyblocks to blocks that will accept pre-terminated IFC or OSP style cables The conversion kits contain thecable management hardware, brackets and cable clamps required to convert the block The kit requiredwill depend on the block style originally purchased

Block style originally purchased

as shown above (blocks ordered before November 2002)

Fanout Bracket Cable

ClampCable Clamping/Block Conversion Kits

Rear Cable Management Tray

for 144 Block Conversion Kit

6/04

Fiber Termination Blocks (FTB) – Preterminated

Preterminated FTBs are available with either indoor or outdoor rated

cable in ribbon or stranded configurations All blocks are 100% factory

tested to guarantee continuity and reliable connections Preterminated

FTBs make installation quick and easy, reducing labor costs Before

ordering, determine the block orientation and cable exit direction

Preterminated FTBs may be ordered with a “left” orientation (mounts

on the left side of the frame) or a “right” orientation (mounts on the

right side of the frame) The cable exit direction will be either “upward”

(cables terminated to the rear side of the block exit up toward the top

of the frame) or “downward” (cables terminated to the rear side of the

block exit down toward the bottom of the frame)

IFC cables loaded into FTB

Catalog Number NGF-TB

† Other cable types are available upon request Please contact your ADC representative.

* House cable will use Corning SMF28, Sumitomo, Alcatel or similar singlemode fiber based on current market availability.

** 144 blocks cannot be used in 26" wide

Length in meters

Cable Length

XXX

8

Adapter/Connector #1 Singlemode

7 L 2 Q X K

5

Connector #2 Singlemode

0 7 L 2 Q X K

6

Block Style

1 2 4

Upward Downward

Block Configuration

A B C M

48 72 96 144**

Block Orientation

L R

Left Right

House cable*

House cable*

Sumitomo Sumitomo Sumitomo

7

Other connector types are available Please contact ADC.