Tài liệu Work with Datasets and XML docx

However, for this example, I also added another button and data grid that will show the data after reading from the XML document.. If the data table has not been saved to the Session obj

12.5 Work with Datasets and XML

Sometimes, I have to pull XML documents into datasets and vice versa How do I

accomplish this using NET?

Technique

.NET has developed a number of ways to utilize datasets and XML together The

simplest use is pushing data between the two To do this, you have the two methods belonging to the DataSet object: ReadXML and WriteXML For both of these methods, you need to provide a filename to read or write the XML document to

To demonstrate how to take advantage of these methods, I created a form that looks similar to the other How-Tos showing how to write XML documents However, for this example, I also added another button and data grid that will show the data after reading from the XML document

Steps

Open and run the Visual Basic NET-Chapter 12 solution From the main Web page, click on the hyperlink with the caption How-To 12.5: Working with Datasets and XML

As with How-To 12.1, when the page loads, you can enter a few names Enter the last and first names, and then click the button labeled Add to DataTable When you have added a few names, click the button labeled Create XML File Using Explorer, open the file created in C:\ called test.xml If you click Read XML File, you will see the same data because it was read from text.xml (see Figure 12.5)

1 Create a Web Form Then place the Labels, TextBoxes, Buttons, and DataGrid objects as seen in Figure 12.5 on the form with the properties set as in Table 12.9

Table 12.9 Label, TextBox, and Button Control Property Settings

Object Property Setting

Button ID btnCreateXMLFile

2 Add the following line to the code module of the form Then place it under the line that reads Web Form Designer Generated Code

3 Dim mdtData As New DataTable()

4 Dim mdsData As New DataSet()

5 Add the code in Listing 12.11 to the Load event of the page If the data table has not been saved to the Session object, then it is created from scratch by first

creating the data columns and then adding them to the data table The DataTable object is then saved to the Session object with the name MyDataTable A DataSet object is also created because some of the XML methods must be used from the DataSet object, rather than at the DataTable level If the Session objects entry already exists, it is assigned back to the module variable mdtData and mdsData Last, the data table is bound to the DataGrid object by calling the BindTheGrid routine, which is described in the next step

Listing 12.11 wfrmHowTo12_5.aspx.vb: Creating a DataTable Object from Scratch

Private Sub Page_Load(ByVal sender As System.Object, _

ByVal e As System.EventArgs) Handles MyBase.Load

'Put user code to initialize the page here

If (Session("MyDataTable") Is Nothing) Then

Dim dcFirstName As New DataColumn()

dcFirstName.ColumnName = "FirstName"

dcFirstName.Caption = "First Name"

mdtData.Columns.Add(dcFirstName)

Dim dcLastName As New DataColumn()

dcLastName.ColumnName = "LastName"

dcLastName.Caption = "Last Name"

mdtData.Columns.Add(dcLastName)

mdsData.Tables.Add(mdtData)

Session("MyDataTable") = mdtData

Session("MyDataSet") = mdsData

Else

mdtData = CType(Session("MyDataTable"), DataTable)

End If

BindTheGrid()

End Sub

6 Create the routine BindTheGrid, shown in Listing 12.12, in the code module for the page

Listing 12.12 wfrmHowTo12_5.aspx.vb: Binding the Data Table to the Data Grid

Sub BindTheGrid()

dgDataToWrite.DataSource = mdtData

dgDataToWrite.DataBind()

End Sub

7 Add the code in Listing 12.13 to the Click event of the btnAdd button This

routine starts off by calling the NewRow method off the mdtData data table, thus creating a new DataRow object The two columns in drNew are replaced with the values in txtLastName and txtFirstName The new row is added to the data table, and the text boxes are cleared Last, mdtData is rebound to the data grid by calling BindTheGrid

Listing 12.13 wfrmHowTo12_5.aspx.vb: Adding Data to the Data Table and Then Rebinding the Data Grid

Private Sub btnAdd_Click(ByVal sender As System.Object, _

ByVal e As System.EventArgs) Handles btnAdd.Click

Dim drNew As DataRow

drNew = mdtData.NewRow()

drNew.Item("LastName") = Me.txtLastName.Text

drNew.Item("FirstName") = Me.txtFirstName.Text

mdtData.Rows.Add(drNew)

Me.txtLastName.Text = ""

Me.txtFirstName.Text = ""

BindTheGrid()

End Sub

8 Add the code in Listing 12.14 to the event of the btnCreateXMLFile button After loading the dataset from the Session object, the WriteXML method is invoked to save the data into an XML document

Listing 12.14 wfrmHowTo12_5.aspx.vb: Creating the XML Document from the Dataset

Private Sub btnCreateXMLFile_Click(ByVal sender As System.Object, _

ByVal e As System.EventArgs) Handles btnCreateXMLFile.Click

mdsData = CType(Session("MyDataset"), DataSet)

mdsData.WriteXml("c:\Test.xml")

End Sub

9 Add the code in Listing 12.14 to the Click event of the btnReadFile button Here, the code reads the XML document by using the ReadXML method off the

dsXMLData DataSet object and then binds it to a DataGrid object

Listing 12.15 wfrmHowTo12_5.aspx.vb: Reading the XML Document Back into the Dataset

Private Sub btnReadFile_Click(ByVal sender As System.Object, _

ByVal e As System.EventArgs) Handles btnReadFile.Click

Dim dsXMLData As DataSet = New DataSet()

dsXMLData.ReadXml("c:\Test.xml")

Me.dgResultsFromXML.DataSource = dsXMLData

Me.dgResultsFromXML.DataBind()

End Sub

Figure 12.5 This XML document was created using XMLTextWriter

Comments

As you can see, for both reading and writing XML document from and to datasets,

Microsoft has given us some easy commands to accomplish the task However, remember that you do have the control over the format of the XML document that you have using the other methods, such as using the DOM