Advances in communications and media research volume 12

Topics include a brief introduction on software radio to ultra wideband radio communications; wideband slotted microstrip antennas for modern applications; Device-to-Device D2D communica

A DVANCES IN C OMMUNICATIONS AND M EDIA R ESEARCH

No part of this digital document may be reproduced, stored in a retrieval system or transmitted in any form or

by any means The publisher has taken reasonable care in the preparation of this digital document, but makes no expressed or implied warranty of any kind and assumes no responsibility for any errors or omissions No liability is assumed for incidental or consequential damages in connection with or arising out of information contained herein This digital document is sold with the clear understanding that the publisher is not engaged in rendering legal, medical or any other professional services

A DVANCES IN C OMMUNICATIONS

Additional books in this series can be found on Nova’s website

under the Series tab

Additional e-books in this series can be found on Nova’s website

under the eBooks tab

A DVANCES IN C OMMUNICATIONS AND M EDIA R ESEARCH

Copyright © 2017 by Nova Science Publishers, Inc

All rights reserved No part of this book may be reproduced, stored in a retrieval system or transmitted

in any form or by any means: electronic, electrostatic, magnetic, tape, mechanical photocopying, recording or otherwise without the written permission of the Publisher

We have partnered with Copyright Clearance Center to make it easy for you to obtain permissions to reuse content from this publication Simply navigate to this publication’s page on Nova’s website and locate the “Get Permission” button below the title description This button is linked directly to the title’s permission page on copyright.com Alternatively, you can visit copyright.com and search by title, ISBN, or ISSN

For further questions about using the service on copyright.com, please contact:

Copyright Clearance Center

Phone: +1-(978) 750-8400 Fax: +1-(978) 750-4470 E-mail: info@copyright.com

NOTICE TO THE READER

The Publisher has taken reasonable care in the preparation of this book, but makes no expressed or implied warranty of any kind and assumes no responsibility for any errors or omissions No liability is assumed for incidental or consequential damages in connection with or arising out of information contained in this book The Publisher shall not be liable for any special, consequential, or exemplary damages resulting, in whole or in part, from the readers’ use of, or reliance upon, this material Any parts of this book based on government reports are so indicated and copyright is claimed for those parts

to the extent applicable to compilations of such works

Independent verification should be sought for any data, advice or recommendations contained in this book In addition, no responsibility is assumed by the publisher for any injury and/or damage to persons or property arising from any methods, products, instructions, ideas or otherwise contained in this publication

This publication is designed to provide accurate and authoritative information with regard to the subject matter covered herein It is sold with the clear understanding that the Publisher is not engaged in rendering legal or any other professional services If legal or any other expert assistance is required, the services of a competent person should be sought FROM A DECLARATION OF PARTICIPANTS JOINTLY ADOPTED BY A COMMITTEE OF THE AMERICAN BAR ASSOCIATION AND A COMMITTEE OF PUBLISHERS

Additional color graphics may be available in the e-book version of this book

Library of Congress Cataloging-in-Publication Data

ISBN: H%RRN

ISSN: 2159-1695

Published by Nova Science Publishers, Inc † New York

Chapter 2 Wideband Slotted Microstrip Antennas

Amel Boufrioua

Chapter 3 Device-to-Device Communications

in 5G Networks: Technical Challenges

Anargyros J Roumeliotis and Athanasios D Panagopoulos

Chapter 4 The Use of Mobile Devices to Support Young

Damian Maher and Kirsty Young

Chapter 5 On the Singular Optimal Control

Vadim Azhmyakov and Carlos M Velezy

Contents

vi

Chapter 6 A Pedagogical Proposal to Support the Teaching

of History with Audiovisual Content, Including Video Game Advertising: The Example

of Assassin`s Creed IV: Black Flag

Enrique Carrasco Molina

P REFACE

In a society predicated on information, the media has a pervasive presence From government policy to leisure television, the information age touches us all The papers collected in this book constitute some of today's leading analyses of the information industry Together, these essays represent

a needed foundation for understanding the present state and future development of the mass media Current trends in communications as well as media impact on public opinion are studied and reported on Topics include a brief introduction on software radio to ultra wideband radio communications; wideband slotted microstrip antennas for modern applications; Device-to-Device (D2D) communication in 5G networks; the use of mobile devices to support young people with disabilities; and singular optimal control of switched systems The final chapter is a proposal to support the teaching of history with audiovisual content, including video game advertising

Chapter 1 – Sixteen years after the dawn of the new millennium, strong trends in telecommunications drive to adaptable wideband communication systems This effort is primarily motivated by two technological concepts: software radio (SWR) and ultra wideband (UWB) communications The design, development and implementation of SWR involve either hardware or software challenges such as analog to digital and digital signal processing speed, power consumption, waveform application portability, software modularity Upon completing all these challenges and with the enormous advantages of UWB communications, fully programmable, unlicensed, low power radios, minimizing interfering with other systems, will be realized Furthermore, due to the large spectral coverage, UWB communications show little loss of penetration in the materials, making it a perfect candidate for emergency applications and harsh environments This chapter focuses on SWR

Anthony V Stavros viii

and UWB technological concepts, and it presents benefits of this combination

as well as limitation and bottlenecks arising Definition, scope, motivation and

a brief history of both technologies are also presented

Chapter 2 – Today, the state of the art antenna technology allows the use

of different types and models of antennas, depending on the area of application considered With the rapid development of wireless communications, it is desirable to design small size, low profile and wideband multi-frequency planar antennas The difficulty of antenna design increases when the number

of operating frequency bands increases The slot loaded patch antenna is used

to overcome this problem This chapter is focused on the multi-band application of the microstrip patch antenna, which is analysed by introducing different slots as U and L-shaped slots in rectangular and circular patches The effects of different physical parameters on the characteristics of the structure are investigated The results in terms of return loss, bandwidth and radiation pattern are given The proposed structures can be scaled to meet different frequencies of wireless communication systems just by changing the dimension of the main antenna Comparisons of return loss and radiation pattern for the same area of the rectangular and circular patches loaded with slot is also given Moreover, U-slot loaded rectangular patch antenna in a stacked geometry with U-slot loaded circular patch antenna and vice versa are analysed The results show that dual wide bands can be achieved and a better impedance matching for the upper and lower resonance can be obtained Also,

it is observed that various antenna parameters are obtained as a function of frequency for different values of slot length and width It is easy to adjust the upper and the lower band by varying these different antenna parameters The theoretical results using Matlab are compared with the simulated results obtained from Ansoft HFSS which are in close agreement Furthermore, comparative studies between our results and those available in the literature is done and showed to be in good agreement

Chapter 3 – The present chapter deals with the concept of Device (D2D) communication networks, their technical implementation and security challenges The first part is an introduction discussing briefly the basic characteristics of D2D communications and their inclusion in the upcoming 5G cellular systems as well as the importance of secure wireless communications Afterwards an overview of D2D framework follows and its standardization history with future enhancements are described Moreover, the 5G requirements and key enablers are indicated and the importance of the implementation of D2D-enabled 5G systems is illustrated Considering the necessity for secure wireless communications various D2D security aspects

Device-to-Preface ix

are presented and the physical layer security techniques are mentioned emphasizing in the secrecy capacity metric Additionally, the integration of secrecy capacity in D2D systems is surveyed and discussed Finally, the chapter concludes with future trends of D2D technology towards its integration in the 5G communications

Chapter 4 – Emerging evidence suggests mobile devices have the potential

to deliver students with disabilities a more equitable education, which is one of the goals set down by the United Nations The focus of this chapter is to explore how mobile devices can be used to support young people with communication disabilities and communication difficulties as a result of isolation The chapter draws upon international legislation and policy documents, research literature and uses a specific case study to highlight the implications and future directions

Chapter 5 – This paper studies a singular case of Optimal Control Problems (OCPs) governed by a class of switched control systems The authors propose a new mathematical formalism for this type of switched dynamic systems and study OCPs with a quadratic cost functionals The original sophisticated optimization problem is next replaced by an auxiliary

“weakly relaxed” OCP Our main result includes a formal proof of the local convexity property of the obtained auxiliary OCP The convex structure of the OCP implies a possibility to apply a variety of powerful and relatively simple optimization schemes to the sophisticated singular OCP involving switched dynamics The conceptual numerical approach the authors finally develop includes an optimal switching times selection (“timing”) and a simultaneous optimal switched modes sequence scheduling (“sequencing”)

Chapter 6 – Based on the analysis of a documentary included in the

advertising campaign to promote the game Assassin`s Creed IV: Black Flag (2013), this study proposes to take, as a methodological resource, view and

analyze various audiovisual resources in order to improve teaching specific aspects of the subjects of History in different education levels Although such games affect their access to age 18, certain content could be shown to students with slightly lower ages

The authors selected as an example a documentary on the life of Spanish privateer born in Tenerife (Canary Islands), Amaro Pargo, a character who lived during the golden age of piracy (XVIII Century) which has been produced by the Spanish delegation of the French multinational Ubisoft The documentary recreates a scientific and archaeological study that reveals the true tomb of Amaro Pargo, under the flagstones of the Church of

This chapter attempts to demonstrate the effectiveness of including in the curriculum content and audiovisual pieces that recreate environments such as those proposed by Assassin`s Creed universe, an imaginative entertainment series that discovers interesting details that are inspired by various historical periods as the FrenchRevolution, or the Seven Years’ War, among others, and include the active presence of some characters actually existed, as Amaro Pargo (in the documentary) or pirate Blackbeard (in the videogame)

In: Adv in Communications and Media Vol 12 ISBN: 978-1-53610-979-5 Editor: Anthony V Stavros © 2017 Nova Science Publishers, Inc

Chapter 1

Vasilis Christofilakis*, Giorgos Tatsis,

Constantinos I Votis and Panos Kostarakis

Physics Department, Electronics-Telecommunications and

Applications Lab, University of Ioannina, Ioannina, Greece

Sixteen years after the dawn of the new millennium, strong trends in telecommunications drive to adaptable wideband communication systems This effort is primarily motivated by two technological concepts: software radio (SWR) and ultra wideband (UWB) communications The design, development and implementation of SWR involve either hardware or software challenges such as analog to digital and digital signal processing speed, power consumption, waveform application portability, software modularity Upon completing all these challenges and with the enormous advantages of UWB communications, fully programmable, unlicensed, low power radios, minimizing interfering with other systems, will be realized Furthermore, due to the large spectral coverage, UWB communications show little loss of

*

Corresponding Author: e-mail: vachrist@uoi.gr, vasilis.christofilakis@gmail.com; Tel.: +30

26510 08542; fax: +30 26510 08674; www.telecomlab.gr

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

2

penetration in the materials, making it a perfect candidate for emergency applications and harsh environments This chapter focuses on SWR and UWB technological concepts, and it presents benefits of this combination

as well as limitation and bottlenecks arising Definition, scope, motivation and a brief history of both technologies are also presented

The invention of the term “Software Radio” in the early 90’s [1] marked the beginning of the transition from digital radios to fully programmable software radio platforms In the literature we find several definitions for the term “Software Radio.” In [2] the concept of SWR is defined as follows:

 “Software Radio” is an emerging technology, thought to build flexible radio systems, multi-service, multi-standard, multi-band, reconfigurable and reprogrammable by software

The following definition is given by [3]:

 “Software radio” means different things to different people - the common ground perhaps is the recognition that the pace of advance in digital and software technologies is not slackening and that these technologies will have a profound impact upon future terminals, not simply mobile phone terminals, but all kinds of consumer devices, ranging from multimedia digital set-top boxes to new Internet-TV products

In [1] Joseph Mitola defines software radio concept as follows:

 “A software radio is a set of Digital Signal Processing primitives, a level system for combining the primitives into communications systems functions and a set of target processors on which the software radio is hosted in real-time communications.”

meta-In fact, all SWR's definitions are covered by the following statement [4]:

 “The placement of the A/D/A converters as close to the antenna as possible and the definition of radio functions in software are the hallmark

of the software radio.”

From Software to UWB Radio Communications 3

However, even if future state of the art A/D/A converters are capable of capturing/transmitting wideband RF signals, something that should not be ignored is the fact that, in practice, it is inevitable to eliminate hardware-dependent stages [5, 6] Just for this reason the Software Radio (SWR) is an ideal system, often found in the literature using the term Software Defined Radio (SDR) 1, which is the functional version of the ideal Software Radio [7] Ultra-Wideband (UWB) technology has recently attracted the attention of both academia and industry for applications in wireless telecommunications This technology has many advantages, such as better immunity to multipath, low power consumption, low interference UWB systems promise high data rates of the order of 100Mbps, suitable for multimedia applications Also, due

to the large spectral coverage, UWB signals present small penetration loss through materials and, therefore, are appropriate in short-range radar and imaging systems, ground penetration radars, wall radar imaging, vehicular radar systems for collision avoidance, guided parking, etc., surveillance systems and medical imaging Wireless communication applications are also

on the scope, including wireless home networking, UWB wireless computer peripherals such as mouse, keyboard, speakers, printers, wireless USB, wireless sensors networks etc Back on April 2002 the Federal Communications Commission (FCC) at USA approved the use of UWB technology for wireless applications The corresponding standards, the IEEE 802.15.3a (short range, high data rate) and the EEE 802.15.4a (low power, low data rates) have been introduced [8]

The design, development and implementation of UWB-SWRs, capable of operating within 3.1 to 10.6GHz band, with bandwidth at least 500MHz, involves either hardware or software challenges such as wide bandwidth ADC’s, digital signal processing throughput, power consumption, waveform application portability, software modularity [9-13] Upon completing all these challenges and with the enormous advantages of UWB communications, reconfigurable, unlicensed, low power radios, minimizing interfering with other systems, will be realized Especially in disaster or crisis areas, where various military, police, fire department and other rescue forces are acting, SWR is the ideal solution since it has the capability to access different bands and frequency ranges of the radio spectrum Additionally, in disaster or crisis areas, the environment is likely to be altered due to demolished buildings, dust and fire, making UWB communications a perfect candidate for such harsh environments since they show little loss of penetration in the materials

1 For simplicity reasons the abbreviation SWR is used instead of SDR

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

4

This chapter gives the reader an opportunity to understand Software Radio and ultra wideband technological concepts as well as the tremendous advantages arising from a UWB-SWR platform

An ideal software radio system essentially uses only four primitives which

are: the Antenna, the A/D/A, the Digital Signal Processing unit and finally the User Interface (Figure 1) It should be clear to the reader that a multi-hardware

radio is not a software radio As shown in Figure 2(a) a multi-hardware radio system can support different operating standards having discrete hardware for each channel Each channel has a different carrier frequency and channel bandwidth and is selected through frequency dependent passive components both for heterodyne and homodyne (zero-IF) architectures Homodyne architectures are better than heterodyne concerning issues of complexity and volume, but suffer from design problems such as I/Q mismatch and DC offset

On the other hand, in the SWR all channels are digitized/transmitted through a wideband A/D/A and the desired channel is digitally selected via the digital signal processing unit (Figure 2(b))

Figure 1 Ideal Software Radio

From Software to UWB Radio Communications 5

Figure 2 (a) Multi-hardware Radio System, (b) Software Radio

Figure 3 Software radio functions

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

6

As shown in Figure 3, the SWR Core consists of several modules including security, frequency band, and modulation schemes Every module (or sub module) in the SWR core could be declared as a class For example all digital modulation schemes could be declared as a DModulation class Instances of this DModulation class are various modulation objects such as fsk() and ask() The bottom line is that in SWR every radio function can be defined through software running on a fast digital signal processing unit (SWR core)

The digital signal processing unit could be based on application specific integrated circuit (ASIC), field programmable gate array (FPGA), digital signal processor (DSP) or a combination of the above In the literature we find additional SWR based on a general processor [14, 15] Usually, the digital signal processing unit is distinguished according to five criteria [16] These are:

 Programmability: The ability and method redefining the system to perform all desired functions for different models

 Integration: The ability to complete the most functions in a single device, which directs to the reduction of complexity and size of the device

 Development Cycle: The time from design to implementation of a specific function, depending mainly on software tools and available sources

 Performance: Execution time of specific functions

 Power Consumption: Crucial for portable devices

An ASIC outperforms others in power consumption and performance, but lacks significantly in programmability which is a primary function of a reconfigurable software radio The FPGAs have evolved from logical design platforms in digital processing “machines.” An FPGA can achieve higher performance compared to a DSP if properly optimized architecture is implemented However, to date, FPGAs have been used almost exclusively for fixed point DSP designs FPGAs have not been viewed as an effective platform for applications requiring high performance floating point computations [17] Advanced floating-point computations such as matrix inversion, matrix multiply and fast Fourier transform are extremely difficult to implement in FPGAs, due to the large amount of data needed in the device [18] Older generation FPGAs had another disadvantage: during the operation they could not be reconfigured [19] New generation FPGAs allow run-time

From Software to UWB Radio Communications 7

fully or partially reconfiguration with time less than 1ms [20] On the other hand, run-time reconfiguration time of a DSP is much smaller and primarily depends on DSP cycle time State of the art DSPs have cycle time less than 1ns [21] Even now there is not specific digital signal processing unit for SWR architecture A combination of DSP and FPGA could finally be a natural choice [22-24] Features, aiming SWR architecture for DSPs and FPGAs, are summarized in the following Table

Table 1 FPGA and DSP features

Feature FPGA DSP

Programming Language VHDL, Verilog C, Assembly, Modeling

Tools Performance Depends on architecture Depends on cycle time Consumption Depends on architecture Depends on peripheral Re-configurability Full Full

Ease of programming Hardware/Software

to the sampling theorem [25] Based on the latest A/Ds surveys [26, 27], state

of the art A/Ds including various technologies and architectures such as Si ICs, III-V ICs (semiconductors are synthesized using elements from third and fifth group of periodic table), SuperCs, Flash, Pipe, SiGe, BiCMOS, SOI CMOS, Nanoscale CMOS have reached such levels of sampling rates that can

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

8

handle ultra wide band limited signals having frequency components lying even around 20-40GHz [28, 29] Even if the sampling frequency satisfies the Nyquist criterion and A/D/A converters can handle above 10GHz full power Input/output bandwidths [30, 31, 32] there are other parameters affecting the performance of an A/D/A Some of these parameters are bit resolution, aperture jitter, differential nonlinearity error (DNL), integral nonlinearity error (INL), full-power analog input bandwidth (FPBW), spurious free dynamic range (SFDR), effective number of bits (ENOB) The parameters just mentioned can play a significant role in real life and can affect the performance of an A/D and thereby the implementation of an ideal SWR [33]

BRIEF HISTORY

Software radio’s origins date back to the military communications of the 70’s and 80’s During that period, besides traditional subjects of cyber warfare, for the first time the focus was on wideband digital techniques which, as mentioned previously, are the beginning of SWR The concept of SWR began

to spread substantially after 1995 A Pioneering military project was the Speakeasy (the military software radio) [34] implemented in two phases from

1992 to 1995 and 1995 to 1997 The main goal of this ambitious project was

an operating frequency range from 2 MHz to 2 GHz and interoperability among various waveforms that include STAJ, PACER bounce, Sincgars, Have quick, EPLRS, JTIDS, GPS and technical Narrow Band modulation (AM / FM) but also as spread spectrum direct sequence spread spectrum - DSSS modulation and spread spectrum Frequency Hopping - FH [35] Eventually, the operating frequency range was between 4 to 400 MHz and the number of waveforms supported much smaller [36] The military organizations expressed further interest in the SWR technology after the project Speakeasy thus creating a group entitled “Programmable, Modular Communications System – PMCS,” which recommended the creation of the Joint Tactical Radio System (JTRS) [37] The global interest in this technology led to the creation in 1996

of the Software Defined Radio Forum The SWR Forum’s aim was to accelerate the spread of technologies relevant to the SWR in wireless telecommunications networks (civil, commercial, military) and participation in the organization of universities, research institutions, companies, industries, network operators, governments aiming prototyping architecture and platform for SWR [38]

From Software to UWB Radio Communications 9

Significant boost to SWR technology was mainly achieved from 1995 to

2005 by research and academic institutions [5, 39-43], but also by international projects such as FIRST (Flexible Integrated Radio Systems Technology), SORT (Software Radio Technology), TRUST (Transparently re-configurable Ubiquitous Terminal), CAST (Configurable radio with advanced software Technology) [44]

Several manufacturers stepped up their efforts and after 2005 and for the last ten years the SWR concept is applied in the commercial and military market Anywave Base Station was the first FCC-certified base station system that fully implemented the base transceiver station (BTS) and base station controller (BSC) entirely in software, running on a general-purpose server [45] Small-form factor (SFF) SDR handheld platform was a joint development between Texas Instruments (TI), Xilinx and Lyrtech as well as a host of leading software tool vendors [46] Motorola Labs also presented a 100 MHz to 2.5 GHz Direct Conversion CMOS Transceiver for SWR applications [47] A software defined tactical radio that provides wideband data performance, interoperability with fielded waveforms and covers 30 MHz to 2 GHz was presented by Harris co [48] Another product was manufactured by Rohde & Schwarz owing to different high-speed data modes and protocols as well as different antijam modes for HF, VHF and UHF [49] The European Secure Software Defined Radio (ESSOR) is another promising programme which started in 2008 The aim of the ESSOR programme is to develop a European software-defined radio technology in order to improve the capabilities for cooperation in joint inter-country operations The first phase of the EDA’s ESSOR programme has now successfully ended In the first phase

of the ESSOR program, the parties were Indra from Spain, Radmor from Poland, Saab from Sweden, Selex ES from Italy, Thales Communications & Security from France and Bittium from Finland The parties are currently in negotiations about the second phase of the program The most important goal

of the second phase is to achieve operational performance for the ESSOR system [50] Latest research, development and commercial efforts on this promising technology are gathered every year in Wireless Innovation Forum

on Communications Technologies and Software Defined Radio [51]

SCOPE AND MOTIVATION

The idea of a unified communication system between commercial, civil, governmental and military organizations certainly attracts numerous

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

10

applications and leads to solving a variety of restrictions and bottlenecks The need for a radio system that can support and communicate with all existing types of military radios is the backbone of military applications A radio system that can not only change the scrambling and encryption but also modulation schemes and channel bandwidth is a highly interesting prospect A system like that could not only prevent hostile eavesdropping attemps, but also

be updated to perform better under certain conditions and different environments

Figure 5 2002: The beginning of broadband (3G), 2008: Global penetration of

broadband reaches 10%, 2015: Global penetration of mobile broadband subscribers reaches 47%

Regarding the commercial sector, further details, such as size, cost, and user friendliness play a major role The problem of incompatibility between different standards can also be resolved using SWR technology As an example, consider the incompatibility of cellular standards from first to the third generation and beyond The pie chart of Figure 5(2002) shows the percentage of mobile subscribers among digital and analog cellular standards

in 2002 [52] The first 3G network offered for commercial use was launched in

From Software to UWB Radio Communications 11

Japan by NTT DoCoMo The network had the brand name FOMA and was introduced in May 2001 on a W-CDMA technology At the time, the overall percentage of other standards such as IS-54, IS-136, usually known as Digital-AMPS (D-AMPS) or TDMA due to the type of multiplexing access, is shown

in Figure 5 (2002) IS-95 with 12% percentage was the first CDMA-based digital cellular standard introduced by Qualcomm All these standards have some common features; on the other hand, each of them requires different technology terminals and base stations (BS) The rapid change after 2006 to broadband has modified the above percentages In the year 2008, there were 4 billion global mobile-cellular subscriptions Mobile broadband subscriptions increased almost a thousand times from 2002 to 2008 with global penetration from 0.01% to 10% (Figure 5 (2008)) [53] Mobile broadband is the most dynamic market segment; globally, mobile-broadband penetration reaches 47% in 2015, a value that increased 12 times since 2007 [54] Additionally, new cellular standards and generations, 5G and beyond meant to be created could be run on SWR base stations and mobile terminals (Figure 6)

Figure 6 Transparency through old, existing and new cellular standards

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

130 million customers in Western Europe and North America while another

100 million customers used the weaker A5/2 version The approximate design

of A5/ leaked in 1994, and the exact design of both A5/1 and A5/2 was reverse engineered by Briceno from an actual GSM telephone in 1999 [55] Only 2 minutes of conversation time (data) and about a few seconds of processing on

a PC are fair enough to extract the conversation key [56] Third Generation cellular communications are protected by the new 128-bit A5/3 algorithm, called Kasumi, a modified version of the MISTY cryptosystem Although A5/3 block cipher is the most recent version, several weaknesses have already been identified [57] Security vulnerabilities in mobile communications could

be easily resolved through over the air upgradability of SWR platforms

Ultra-Wideband (UWB) technology is a relatively new entry in the world

of telecommunications that has attracted the attention of the scientific community As its name implies, and according to the definition of the Federal Communication Committee (FCC), a wireless scheme is considered as UWB

if the absolute bandwidth occupied is greater than 500 MHz or the fractional bandwidth is over 20% FCC also has set the limits of the maximum emission power for indoor and outdoor applications in the United States (US), reserving

an unlicensed band between 3.1-10.6 GHz in which the maximum radiated power is -41.3 dBm/MHz [58] The spectral mask released by the FCC in 2002

is depicted in Figure 7 In European Union (EU) accordingly, the ETSI (European Technical Standard Institute) and CEPT (European Conference of Postal and Telecommunications) are still working for these limits According

to the latest at the time report for indoor short-range devices (SRD) the corresponding spectral mask is depicted in Figure 8 [59] The EU limits are more restricted than those in US, in a manner to avoid interference with other technologies Special mitigation techniques are required such as Low Duty Cycle (LDC) abd Detect And Avoid (DAA) to permit the maximum power in the bands 3.1-4.8 GHz and 8.5-9 GHz The corresponding highest radiated

From Software to UWB Radio Communications 13

power without mitigation band is between 6-8.5 GHz with the same level as the FCC

The dominant technique for generating UWB signal in the literature is the use of very short-duration pulses of the order of 1nsec This scenario is also known as Impulse Radio UWB (IR-UWB) [60], although a multi-band scenario based on Orthogonal Frequency Division Multiplexing (OFDM) is also under study [61, 62] Typical shapes of the pulses are Gaussian-like or similar to the derivatives of a Gauss pulse Figure 9 depicts a possible UWB pulse with the form of the first Gaussian derivative and the corresponding spectrum One may notice how the short duration in time domain spans the frequencies over the spectrum giving the ultra-wideband nature in the signal Other pulse shapes are also under the scope regarding optimality and spectral compatibility [63] Also pulsed based UWB systems exploit a variety of modulation types such as Pulse Amplitude Modulation (PAM) including the simplest On-Off Keying (OOK), Pulse Position Modulation (PPM) and Phase Shift Keying (PSK) [64-66]

Figure 7 FCC spectral mask for UWB

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

14

Figure 8 European spectral mask for UWB

UWB technology has some significant advantages over conventional narrowband systems

 Low complexity: The UWB signal is by nature a baseband signal, consisting of a sequence of very short baseband pulses There is no need to use up-down converting stages or mixing with carriers

 Low interference: UWB signal is seen by other coexisting narrowband technologies as a noise-like signal due to its relatively large bandwidth and at the same time the very low transmitting power

 Resistance to multipath: The enormous bandwidth allows the high multipath resolution, meaning a large number of resolvable paths to the receiver

 High time domain resolution: The use of very short pulses in UWB signals is an asset in the application that requires accuracy in space such as radar, location, posisioning etc

 Spectral efficiency: The use of very large spectrum bandwidth increases significantly the spectral efficiency of UWB systems

From Software to UWB Radio Communications 15

Figure 9 UWB pulse in time domain (up) and corresponding spectrum (down) Several transceiver architectures have been proposed The implementation

of the transmitter is relatively easier than the receiver The transmitter usually consists of an analog pulse generator that is controlled by software-based devices according to the modulation scheme used The conventional UWB pulse generator is based commonly on step recovery diodes A step recovery diode (SRD) can produce a short in time output pulse triggered by a regular square pulse [67-71] Data modulation can be done using square pulses in digital logic and the SRD circuitry acts as the pulse shaper for the final form of the UWB pulses that are driven finally to an antenna The receiver on the other side has a more difficult job Due to the strong impact of the multipath channel the transmitted signal is distorted The UWB indoor channel impulse response can be seen as a digital filter with several taps with different delays and gains representing the different paths in the channel due to reflections or diffractions

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

16

[72,73] Figure 10 shows a simulated received waveform through such a channel with strong interference, coming from a single transmitted pulse, having the form of the second Gaussian derivative (Scholtz’s monocycle) One may observe the multiple copies of the initial pulse in different time positions spreading the waveform for several nanoseconds

Figure 10 Simulated received UWB waveform in indoor multipath environment Usually, one has to tradeoff the low complexity and simplicity with the performance which tends to be both power and computationally expensive The energy detector is the simplest approach but with the poorest noise performance It consists of a square-law device followed by an integrator and the estimation of the symbols is done by the energy output and a predefined threshold The RAKE receiver on the other hand is an optimized receiver for best performance in multipath channels [74-79] It exploits the advantage of the high temporal resolution of UWB signals to distinguish different paths The fingers of the receiver correspond to those paths The drawback of this system is the complexity Dense multipath environment may require a large number of fingers that is very difficult to implement Also, channel estimation

is necessary on the receiver side Another candidate UWB transceiver type is the Transmitted Reference system (TR) [80-86] The main idea of this scenario

is that for each symbol pulse a reference pulse is transmitted first The time distance between the pulses is known to the receiver and it uses

From Software to UWB Radio Communications 17

autocorrelation detection technique Each pulse actually is correlated with the reference of it which is virtually the same waveform at different time The advantage of this method is that there is no need to estimate the channel’s response

One of the greatest challenges in modern telecommunication systems is a fully software-defined reconfigurable transceiver structures and operations IR-UWB trends to that concept and great effort takes place now days to reach the ideal SDR solution as much as possible In an ideal SDR transmitter only one Digital to Analog converter (DAC) is able to replace all the analog parts used to generate the transmitted signal, and it just needs to be connected to the software device, processing the logic of the system, and to the antenna, as depicted in Figure 1 In an IR-UWB SDR concept a DAC is used to produce the ultra-short pulse instead of an analog pulse shaper in order to be reconfigurable Because impulsive UWB technologies essentially are digital in nature — without the attending complexities of RF front-end designs — a variety of such technologies potentially could be realized with the same chipset [87] In [88] a reconfigurable UWB transceiver is presented At the transmitter side the authors used a multi-Nyquist DAC (Digital to Analog Converter) that generates the UWB pulse In order to avoid up-converting stages, the bandpass sampling technique is used [89] The DAC’s sampling rate is 2 GS/s, therefore a pulse of 1 GHz bandwidth is generated, and the RF bandwidth is between 2-3 GHz The same principle would be implemented for higher frequencies The limitations of current technology especially in sampling rates of the order of GHz together with the following processing of such enormous data rate lead us to less ideal solutions but yet effective without loss of reconfigurability A mixed solution with analog components assisted and configured by software (digital part) is a fair compromise between the ideal software radio and a realistic reconfigurable transceiver implementation The today’s possibilities of components integration into a single chip makes this idea practical In [90] an IR-UWB reconfigurable transceiver is implemented using distributed circuit techniques, fabricated in a custom 0.18um CMOS chip for this purpose Both the transmitter and the receiver utilize the time interleaving technique [91, 92], in order to multiply the sampling rate of the system and thus the time resolution without increasing the operating rate of individual components, that uses a much lower rate The

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

18

authors measured an energy efficiency of 25-pJ/pulse for the transmitter and 190pJ/pulse for the receiver, due to heavy data manipulation that is power consuming, with a maximum of 250 MHz pulse rate UWB technology is a promising technology with great future and with the capabilities and potential for implementation of a real software radio, although technical obstacles need

to be overcome Regarding A/D and D/A speeds, there has been a remarkable progress in the last years and several GSamples/sec of data rate are already attained [93-95] The bit resolution is usually about 4-6 bits, and it is notable that even for a resolution of 4 bit is sufficient for a typical UWB pulse detection [96] On the transmit side it seems that a fully software defined UWB Impulse Radio transmitter is feasible satisfying the low-cost implementation On the receive side, more effort needs to be made The pure software-based processing of huge amount of raw A/D data is still a major challenge A mix of digital and analog components for signal detection that are configured by software is a vital middle ground solution in favor of reconfigurability Parallel processing techniques, like the ones offered by FPGAs, are needed in order to manage the high data rate that UWB technology handles [97- 99]

Digital Real-Time Baseband processing for UWB communications remains a challenging task Even for real-time modulation/demodulation of typical wireless protocol packets, the digital baseband processor must operate

at an efficiency of 100 million operations per second (Mops) per milliwatt (mW) Most embedded DSP and FPGA systems operate at an efficiency of approximately 10 Mops/mW [100] Low power ultra-wide band digital baseband implementations do exist, but only in a few works are stated to be programmable [101- 103]

HARDWARE “INDEPENDENCE” USING SMART

Technology evolution drives to a gradual transition from hardware to software i.e., shifting the line software / hardware from baseband to the antenna (Figure 1) The question evidently arising is whether the antenna can

be hardware independent Before answering this reasonable question, let's take

a look at the definition of the antenna The antenna is defined as the transmission or reception media of radio waves [104] The common types of antennas are characterized by basic parameters and characteristics generally

From Software to UWB Radio Communications 19

remaining unchanged and, through the antenna pattern, are plotted as a function of spatial coordinates One commonly adopted way for allowing a radiation pattern variation can be achieved using a smart antenna [105] A smart antenna (Figure 11) could form beams towards the desired angles and null beams towards the undesired interferences using two or more antennas (antenna array) through a spatial filtering, most often encountered as beamforming [106] In the literature, the terms: software, adaptive, intelligent and configurable [107] are additionally used Apart from the broadband antenna elements, UWB antenna arrays arrangement are in general similar to the arrangement of narrowband antenna arrays Of cource, there are structural differences due to the large bandwidth needed for UWB In particular, the requirements for the phase relationship between the array elements often necessitate more stringent design considerations [108] Concerning UWB elements, planar and printed monopole antennas are the right candidates for use in UWB wireless technology because of their wide impedance bandwidth and nearly omnidirectional azimuthal radiation pattern [109] The bottom line

is that conventional antennas could not be hardware independent On the contrary, smart UWB antennas, as an implementation aspect of SWR, can bring additional flexibility and improvements in both commercial and military applications including: Increased capacity to users, reduced interference, power consumption, better security, reduced electromagnetic pollution

Figure 11 Space Division Multiple Access using BS smart antennas

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

20

Both Software Radio and Ultra Wideband Communications are evolving continuously remaining hot issues with various open fields that should be addressed Due to the recent boost in several technologies and mainly in fast-wideband A/D/As and baseband processors as well as programmable pulse generators, the UWB-SWR platform implementation tends to be a realistic goal The UWB-SWR platform transfers radio bounds from hardware to software offering tremendous advantages, not limited to cost reduction, flexibility, reliability, future proof, interconnectivity, low power and complexity

to Cognitive Radio.” EURASIP J Wirel Commun Netw 2005, no 3

(2005): 652784 doi:10.1155/wcn.2005.275

[8] Tatsis, Giorgos Ultra-Wideband Wireless Link Characterization Utilizing Software Radio [S.l.]: Lap Lambert Academic Publ, 2012 [9] Kenington, P.B., and L Astier “Power consumption of A/D converters

for software radio applications.” IEEE Trans Veh Technol 49, no 2

(2000): 643-650 doi:10.1109/25.832996

From Software to UWB Radio Communications 21

[10] Hentschel, T., and G Fettweis “Sample rate conversion for software

radio.” IEEE Commun Mag 38, no 8 (2000): 142-150

doi:10.1109/35.860866

[11] Dong, Molang, Weiji Su, Lin Zhang, and Xiuming Shan “The Concept

of Modularity Design in Software Radio.” 2008 4th International Conference on Wireless Communications, Networking and Mobile Computing, 2008 doi:10.1109/wicom.2008.330

[12] Rivet, Francois, Yann Deval, Jean-Baptiste Begueret, Dominique Dallet, Philippe Cathelin, and Didier Belot “From Software-Defined to Software Radio: Analog Signal Processor features.” 2009 IEEE Radio and Wireless Symposium, 2009 doi:10.1109/rws.2009.4957351

[13] Christensen, E., A Miller, and E Wing “Waveform Application Development Process for software defined radios.” MILCOM 2000 Proceedings 21st Century Military Communications Architectures and Technologies for Information Superiority (Cat No.00CH37155) (n.d.) doi:10.1109/milcom.2000.904945

[14] Tan, Kun, He Liu, Jiansong Zhang, Yongguang Zhang, Ji Fang, and Geoffrey M Voelker “Sora.” Communications of the ACM 54, no 1 (2011): 99 doi:10.1145/1866739.1866760

[15] Bose, V., M Ismert, M Welborn, and J Guttag “Virtual radios.” IEEE

J Select Areas Commun 17, no 4 (1999): 591-602 doi:10.1109/

[18] Rudra, A “The Rising Importance of FPGA Technology in Software Defined Radio.” COTS Journal: The Journal of Military Electronics and Computing 7 (January 2005) http://www.cotsjournalonline.com/ articles/print_article/100247

[19] Cummings, M., and S Haruyama “FPGA in the software radio.” IEEE Commun Mag 37, no 2 (1999): 108-112 doi:10.1109/35.747258

[20] Leveugle, R., L Antoni, and B Feher “Dependability analysis: a new

application for run-time reconfiguration.” Proceedings International Parallel and Distributed Processing Symposium (n.d.) doi:10.1109/

ipdps.2003.1213319

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

22

[21] BDTI-Pocket Guide to Processors for DSP, Nov 2013 (Berkeley Design Technology, Inc | Www.bdti.com Accessed March 28, 2016 http://www.bdti.com/MyBDTI/pg/BDTIPocketGuide.pdf

[22] Delahaye, Jean-Philippe, Guy Gogniat, Christian Roland, and Pierre Bomel “Software Radio and Dynamic Reconfiguration on a DSP/FPGA

platform.” Frequenz 58, no 5-6 (2004)

doi:10.1515/freq.2004.58.5-6.152

[23] Anjum, Omer, Tapani Ahonen, Fabio Garzia, Jari Nurmi, Claudio Brunelli, and Heikki Berg “State of the art baseband DSP platforms for Software Defined Radio: A survey.” EURASIP J Wirel Commun Netw

2011, no 1 (2011): 5 doi:10.1186/1687-1499-2011-5

[24] Podosinov, V S “A Hybrid DSP and FPGA System for Software Defined Radio Applications.” Master's thesis, Virginia Polytechnic Institute and State University, 2001 http://vtechworks.lib.vt.edu/ handle/10919/31810

[25] C.E Shannon, Communication in the Presence of Noise, Proc of IRE, vol 37 pp 10-21, January 1949

[26] “Boris Murmann: ADC Survey.” Stanford University Accessed March

[29] Kull, Lukas, Thomas Toifl, Martin Schmatz, Pier A Francese, Christian Menolfi, Matthias Braendli, Marcel Kossel, Thomas Morf, Toke M Andersen, and Yusuf Leblebici “22.1 A 90GS/s 8b 667mW 64× interleaved SAR ADC in 32nm digital SOI CMOS.” 2014 IEEE International Solid-State Circuits Conference Digest of Technical Papers (ISSCC), 2014 doi:10.1109/isscc.2014.6757477

[30] Huang, Hao, Johannes Heilmeyer, Markus Grozing, and Manfred

Berroth “An 8-bit 100-GS/s distributed DAC in 28-nm CMOS.” 2014 IEEE Radio Frequency Integrated Circuits Symposium, 2014

doi:10.1109/rfic.2014.6851659

From Software to UWB Radio Communications 23

[31] Fujitsu Global Accessed March 25, 2016 https://www.fujitsu.com/ uk/Images/c60.pdf

[32] Fujitsu Global Accessed March 25, 2016 http://www.fujitsu.com/ downloads/ MICRO/fma/pdf/56G_ADC_FactSheet.pdf

[33] Christofilakis, V., A A Alexandridis, K Dangakis, and P Kostarakis

“Analog to Digital Converter: a Key Concept in the Implementation of a 3G Software Defined Radio Receiver.” In Thessaloniki 2002 doi:10.1.1.12.845

[34] Lackey, R.I., and D.W Upmal “Speakeasy: the military software radio.” IEEE Commun Mag 33, no 5 (1995): 56-61 doi:10.1109/35.392998

[35] Gunn, J.E., K.S Barron, and W Ruczczyk “A low-power DSP

core-based software radio architecture.” IEEE J Select Areas Commun 17,

no 4 (1999): 574-590 doi:10.1109/49.761037

[36] Cook, P.G., and W Bonser “Architectural overview of the SPEAKeasy

system.” IEEE J Select Areas Commun 17, no 4 (1999): 650-661

[39] Evans, J.B., G.J Minden, K.S Shanmugan, G Prescott, V.S Frost, B

Ewy, R Sanchez, et al “The rapidly deployable radio network.” IEEE J Select Areas Commun 17, no 4 (1999): 689-703 doi:10.1109/49

761045

[40] Shah, A B “Software-Based Implementation of a Frequency Hopping Two-Way Radio.” Master's thesis, Massachusetts Institute of Technology, 1997 http://dspace.mit.edu/bitstream/handle/ 1721.1/ 42785/38572341-MIT.pdf?sequence=2

[41] Welborn, M.L “Direct waveform synthesis for software radios.”

WCNC 1999 IEEE Wireless Communications and Networking Conference (Cat No.99TH8466) (n.d.) doi:10.1109/wcnc.1999.797817

[42] Mitola III, J “Cognitive Radio An Integrated Agent Architecture for Software Defined Radio.” PhD diss., Royal Institute of Technology (KTH), Sweden, 2000

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

24

[43] Srikathyayani, S “Design and Implementation of a Soft Radio Architecture for Reconfigurable Platforms.” PhD diss., 2001 https://theses.lib.vt.edu/theses/available/etd-07232001-201851/

unrestricted/Srikanteswara_etd.pdf

[44] “Home Page - Research & Innovation - European Commission.” European Commission Accessed March 28, 2016 http://ec.europa.eu/ research/index.cfm

[45] Vanu, Inc “Vanu, Inc Announces Commercial Availability of Anywave Base Station; First FCC-Certified Software Radio Device Deployed Live

in Mid Tex Cellular Network.” CTIA Wireless 2005, March 2005 [46] Belanger, Λ “Advanced SDR platform eases multiprotocol radio development.” RF Design Magazine, January 2007

[47] Cafaro, Gio, Tom Gradishar, Joe Heck, Steve Machan, Geetha Nagaraj, Scott Olson, Raul Salvi, Bob Stengel, and Bill Ziemer “A 100 MHz 2.5 GHz Direct Conversion CMOS Transceiver for SDR Applications.”

2007 IEEE Radio Frequency Integrated Circuits (RFIC) Symposium,

2007 doi:10.1109/rfic.2007.380862

[48] 10_tcm26-9017.pdf

http://rf.harris.com/media/AN-PRC-117G%28V%291%28C%29%2012-[49] http://cdn.rohde-schwarz.com/pws/dl_downloads/dl_common_library/ dl_brochures_and_datasheets/pdf_1/M3TR-family_bro_en_5213-9228-12_v0500.pdf

[50] http://www.euro-sd.com/fileadmin/user_upload/daten/produkte/esd/ ESD_Spotlight_No_21.pdf

[51] http://www.conference.wirelessinnovation.org/

[52] EMC World Cellular Information Service, Informa Telcoms & Media [53] ICT Facts and Figures, 2011 http://www.itu.int/ITU-D/ict/facts/2011/ material/ICTFactsFigures2011.pdf

[54] Global mobile statistics 2013 Part B: Mobile Web; mobile broadband penetration; 3G/4G subscribers and networks October 2013 Web 17 October 2013

[55] Briceno, Μ., Ι Goldberg, and Δ Wagner “A5/1 Pedagogical Implementation.” Smartcard Developer Association Accessed March

28, 2016 http://www.scard.org/gsm/a51.html

[56] Biryukov, Alex, Adi Shamir, and David Wagner “Real Time Cryptanalysis of A5/1 on a PC.” Fast Software Encryption, 2001, 1-18 doi:10.1007/3-540-44706-7_1

From Software to UWB Radio Communications 25

[57] Dunkelman, Orr, Nathan Keller, and Adi Shamir “A Practical-Time Related-Key Attack on the KASUMI Cryptosystem Used in GSM and 3G Telephony.” Advances in Cryptology – CRYPTO 2010 Lecture Notes in Computer Science, 2010, 393-410

[58] Federal Communications Commission, “Revision of Part 15 of the Commission’s Rules Regarding Ultra-Wideband Transmission Systems,” ET Docket 98-153, Released: April 22, 2002, https://transition.fcc.gov/Bureaus/Engineering_Technology/Orders/2002/fcc02048.pdf

[59] Short Range Devices (SRD) using Ultra Wide Band (UWB), Technical Report, ETSI TR 103 181-1 V1.1.1 (2015-07) “http://www.etsi.org/ technologies-clusters/technologies/radio/ultra-wide-band.”

[60] Moe Z Win and Robert A Scholtz, “Impulse radio: How it works,”

IEEE Communications Letters, vol 2, no 1, Jan 1998, pp 10-12

[61] E Saberinia and A H Tewfik, “Multi-user UWB-OFDM Communications,” IEEE Pacific Rim Conference on Communications, Computers and Signal Processing, Victoria, Canada, vol 1, pp 127–130,

2003

[62] J Balakrishnan, A Batra, and A Dabak, “A multi-band OFDM system for UWB communication,” Conference on Ultra-Wideband Systems and Technologies, Reston, VA, 2003, pp 354–358

[63] X Luo, L Yang, and G B Giannakis, “Designing optimal

pulse-shapers for ultrawideband radios,” Journal of Communications and Networks, Vol 5, No 4, December 2003

[64] Robert C Qiu, Huaping Liu, Xuemin Shen, “Ultra-Wideband for

Multiple Access Communications,” IEEE Communications Magazine,

Feb 2005

[65] I Guvenc and H Arslan, “On the Modulation Options for UWB

Systems,” IEEE Milcom ’03, Oct 2003, pp 892–97

[66] Moe Z Win and Robert A Scholtz, “Ultra-Wide Bandwidth Hopping Spread-Spectrum Impulse Radio for Wireless Multiple-Access

Time-Communications,” IEEE Transactions on Communications, vol 48, no

4, April 2000, pp 679–689

[67] Jeongwoo Han and Cam Nguyen, “A New Ultra-Wideband, Ultra-Short

Monocycle Pulse Generator With Reduced Ringing,” IEEE Microwave And Wireless Components Letters, Vol 12, No 6, June 2002

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

26

[68] Pavel Protiva, Jan Mrkvica, and Jan Machac,”A compact step recovery

diode subnanosecond pulse generator,” Microwave and Optical Technology Letters, Vol 52, No 2 February 2010

[69] Hiroyuki KIDA, “Measured and Simulated Results of Impulse Generator

Using Step Recovery Diode,” IEICE Transactions on Fundamentals of Electronics, Communications and Computer Sciences, Vol E88-A, No.9

[71] Tzyh-Ghuang Ma, Chin-Jay Wu, Po-Kai Cheng, and Chin-Feng Chou,

“Ultrawideband Monocycle Pulse Generator With Dual Resistive

Loaded Shunt Stubs,” Microwave and Optical Technology Letters, Vol

49, No 2, February 2007

[72] IEEE P802.15 Working Group for WPAN, “Channel Modeling

Sub-committee Report Final,” IEEE P802.15-02/490rl-SG3a, 7 February,

2003

[73] A A Saleh and R A Valenzuela, “A statistical model for indoor

multipath propagation,” IEEE Journal on Selected Areas in Communications, vol.5,no.2, pp.128–137,1987

[74] D Cassioli, M Z Win, and A F Molisch, “Effects of spreading

bandwidth on the performance of UWB RAKE receivers,” IEEE Int Conf Commun (ICC), vol 5, pp 3545–3549, 2003

[75] M Z Win, G Chrisikos, and N R Sollenberger, “Performance of RAKE reception in dense multipath channels: implications of spreading

bandwidth and selection diversity order” IEEE Journal of Selected Areas

[77] N Boubaker and K Letaief, “A low complexity MMSE-RAKE receiver

in a realistic UWB channel and in the presence of NBI,” IEEE Wireless Communications Networking Conference (WCNC), vol 1, pp 233–237,

2003

From Software to UWB Radio Communications 27

[78] D Cassioli, M Z Win, F Vatalaro, and A F Molisch, “Performance of

low-complexity RAKE reception in a realistic UWB channel,” IEEE Int Conf Commun (ICC), vol 2, pp 763–767, 2002

[79] L Yang and G B Giannakis, “A General Model and SINR Analysis of Low Duty-Cycle UWB Access Through Multipath with Narrowband

Interference and Rake Reception” IEEE Transactions in Wireless Communications, vol 4, no 4, pp 1818–1833, 2005

[80] Y Chao and R A Scholtz, “Optimal and suboptimal receivers for

ultra-wideband transmitted reference systems,” Global Telecommunications Conference, pp 744–748, San Francisco, 2003

[81] H Zhang and D L Goeckel, “Generalized transmitted-reference UWB

systems,” Conf on Ultra-Wideband Systems and Technologies, Reston,

VA, 2003, pp 147–151

[82] T Quek and M Win, “Ultrawide bandwidth transmitted-reference

signalling,” IEEE International Conference on Communications, vol.6,

pp 3409–3413, 2004

[83] S Franz and U Mitra, “Integration interval optimization and

performance analysis for UWB transmitted reference systems,” IEEE Ultrawideband Systems Technology (UWBST), pp 26–30, Kyoto, 2004

[84] G Leus and A.-J van der Veen, “Noise suppression in UWB transmitted

reference systems,” IEEE 5th Workshop on Signal Processing Advances

in Wireless Communications, Lisbon, 2004

[85] J D Choi and W.E Stark, “Performance of ultra-wideband

communications with suboptimal receivers in multipath channels,” IEEE Journal on Selected Areas in Communications, vol.20, pp.1754–1766,

2002

[86] R Hoctor and H Tomlinson, “Delay-hopped transmitted-reference RF

communications,” IEEE Conference on Ultra Wideband Systems and Technologies (UWBST’02), pp.265–269, 2002

[87] Santhoff, J., and D Cummings “UWB brings radio's future closer.”

Mobile Radio Technology 22, no 11 (November 2004): 18

[88] M D Blech, A T Ott, P Neumeier, M Moller, and T F Eibert, “A reconfigurable software defined ultra-wideband impulse radio

transceiver,” Advances in Radio Science, Vol 8, pp 67–73, 2010

[89] R G Vaughan, N L Scott and D R White, “The theory of bandpass

sampling,” in IEEE Transactions on Signal Processing, vol 39, no 9,

pp 1973-1984, Sep 1991

Vasilis Christofilakis, Giorgos Tatsis, Constantinos I Votis et al

[91] W C Black and D A Hodges, “Time interleaved converter arrays,” in

IEEE Journal of Solid-State Circuits, vol 15, no 6, pp 1022-1029, Dec

[94] Yunliang Zhu, Jonathan D Zuegel, John R Marciante and Hui Wu, “A

10 GS/s Distributed Waveform Generator for Sub-Nanosecond Pulse

Generation and Modulation in 0.18μm Standard Digital CMOS,” IEEE Conference Radio Frequency Integrated Circuits (RFIC) Symposium,

2007

[95] S Cai, E Z Tabasy, A Shafik, S Kiran, S Hoyos and S Palermo, “A 25GS/s 6b TI binary search ADC with soft-decision selection in 65nm CMOS,” VLSI Circuits (VLSI Circuits), 2015 Symposium on, Kyoto,

2015, pp C158-C159

[96] Puneet P Newaskar, Raul Blazquez and Anantha P Chandrakasan,

“A/D Precision Requirements for Digital Ultra-Wideband Radio

Receivers,” Journal of VLSI Signal Processing 39, 175–188, 2005

[97] Anderson, C R “A Software Defined Ultra Wideband Transceiver Testbed for Communications, Ranging, and Imaging.” PhD diss., Virginia Polytechnic Institute and State University, 2006

[98] Blanton, M B “An FPGA Software-Defined Ultra Wideband Transceiver.” Master's thesis, Bradley Department of Electrical and Computer Engineering Blacksburg, Virginia, 2006 https://theses.lib.vt edu/theses/available/etd-09082006-094650/unrestricted/thesis.pdf [99] Argarwal, D., R Christophe, and M Peter “An 8-GHz Ultra Wideband

Transceiver Prototyping Testbed.” 16th IEEE International Workshop

on Rapid System Prototyping (RSP'05) (n.d.) doi:10.1109/rsp.2005.12