188138637 flexi EDGE BTS SW EX5 1 0 2 release documentation

EX5 1.0.2 Release Upgrade Instructions Nokia Siemens Networks © CONFIDENTIAL Release Upgrade Instructions Id: EX5 1.0.2 Product Family: Base Stations Product: Flexi EDGE Base Station

Trang 1

Change Note Forms

Release Upgrade Instructions

Verification Document

Feature Descriptions

Trang 2

EX5 1.0.2 Summary of Corrections and Enhancements

Nokia Siemens Networks ©

CONFIDENTIAL

Summary of Corrections and Enhancements

Id: EX5 1.0.2 Product Family: Base Stations Product: Flexi EDGE BTS Release: EX5

Approval date: 28th May 2013

Trang 3

CONFIDENTIAL

Table of Contents

1 Corrections 3

2 New / Changed functionality 3

3 3rd party corrections 3

4 Previous deliveries for the release 4

5 Appendices / References 4

Contact

Contact your local Nokia Siemens Networks support or GSM/EDGE BTS Technical Support:

bts.technicalsupport@nsn.com

Summary of changes

Trang 4

The following corrections are included in Flexi EDGE BTS SW EX5 1.0.2

• NA05287875, NA05319320, NA05324546 One way or two way silence in calls during high traffic load of high capacity Packet Abis over Ethernet sites

• NA05377115 Overload threshold values too high

• NA05242504, NA05315599 High TCH drop call ratio

• NA05372623 Diffserv value of the PWE Tunnel at BTS can`t be set correctly

• NA05347098 BTS Manager application does not allow /30 mask for peer IP address

• NA05297378 Packet abis site restored only after giving ESMA HW power reset The problem descriptions are detailed in the latest published Flexi EDGE BTS LGF document in NOLS

2 NEW / CHANGED FUNCTIONALITY

The following new functionalities are included in Flexi EDGE BTS SW EX5 1.0.2

• BTS overload control has been implemented both for TDM and Packet Abis

Please find detailed information about the enhancement in Flexi EDGE BTS Feature Descriptions ‘BTS Overload Control’ included in the Flexi EDGE BTS EX5 1.0.2 Release Documentation released together with the SW in NOLS

3 3RD PARTY CORRECTIONS

None

Trang 5

CONFIDENTIAL

4 PREVIOUS DELIVERIES FOR THE RELEASE

EX5 SW Delivery

EX5 0.0.1 SW Delivery

EX5 1.0.0 SW Delivery

EX5 1.0.2 SW Delivery Release Date 31-Dec-2012 5-Feb-2013 2-Apr-2013 28-May-2013

BTS SW Products

BTS Software A5/0

BTSE5000.7CX Build 124 Version 5.00-00

BTSE5000.A6X Build 166 Version 5.00-16

BTSE50A0.28X Build 040 Version 05.10-00

BTSE50A0.6AX Build 106 Version 05.10-32

BTS Software A5/3

BTSE5003.7CX Build 124 Version 5.00-03

BTSE5003.A6X Build 166 Version 5.00-19

BTSE50A3.28X Build 040 Version 05.10-03

BTS Software IPSec

BTSE50A3.28L Build 040 Version 05.10-03

BTS Manager

Application

2G BTS Site Manager Version EX5 Build 129

2G BTS Site Manager Version EX5 0.0.1 Build 162

2G BTS Site Manager Version EX5 1.0.0 Build 043

2G BTS Site Manager Version EX5 1.0.2 Build 106

Related products

SiteWizard SiteWizard 9 n/a n/a n/a

FIFA

FIFA Software 1.3

Code:P59303.01 D0

Build:

FIF_1.3-02

-D0

Code:P59303.01-Build: FIF_1.3-02

-D0

Code:P59303.01-Build: FIF_1.3-02

FIFA Software 1.3 Code:P59303.01 D0

Build: FIF_1.3-02

5 APPENDICES / REFERENCES

/1/ GSM/EDGE BSS, rel RG30(BSS), Operating Documentation, Issue 02, available in NOLS

Trang 6

as part of the process of continuous development and improvement of the documentation

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given

“as is” and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document

Nokia Siemens Networks will correct errors in this documentation as soon as possible

IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED

TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws

The wave logo is a trademark of Nokia Siemens Networks Oy Nokia is a registered trademark of Nokia Corporation Siemens is a registered trademark of Siemens AG

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only

Trang 7

EX5 1.0.2 Impact Document

CONFIDENTIAL

Impact Document

Id: EX5 1.0.2 Product Family: Base Stations Product: Flexi EDGE BTS Release: EX5

Trang 8

CONFIDENTIAL

Table of Contents

1 Purpose 3

2 Release delivery effect 3

3 Effects on end-users 3

3.1 Performance 3

4 Effects on operator 4

4.1 Operability 4

5 Appendices / References 4

Contact:

Contact your local Nokia Siemens Networks support or GSM/EDGE BTS Technical Support: bts.technicalsupport@nsn.com

Summary of changes:

Trang 9

This document describes the new corrections and feature enhancements delivered in Flexi EDGE BTS SW EX5 1.0.2

2 RELEASE DELIVERY EFFECT

This EX5 1.0.2 BTS software priority package contains:

• 6 new corrections and 1 new feature EX5 1.0.2 can be background downloaded to the BCF prior to activation Activation of the BTS software will cause momentary loss of service in the serving cells as the BCF will be reset

The typical SW background loading times Conventional Abis with 64 kbit/s OMUSIG ~1 hour

Software activation: ~ 2½ - 4 minutes (no service during this time)

3 EFFECTS ON END-USERS

3.1 Performance

Flexi EDGE BTS End User Performance is improved with the following corrections and feature enhancement:

• NA05242504 High TCH drop call ratio

• NA05287875, NA05319320, NA05324546 One way or two way silence in calls during high traffic load of high capacity Packet Abis over Ethernet sites

• NA05377115 Overload threshold values too high

BTS Overload Control

• The tested performance improvement for both TDM and Packet Abis:

o Approximately 20 % improvement in BTS capability to handle signalling/messages per second has been seen in R&D tests compared to earlier BTS SW releases Tests have been done with Flexi Multiradio BTS EDGE, but the same code changes affect also Flexi EDGE BTS

o Detailed information of the changes and their impact can be seen in Flexi EDGE BTS Feature Descriptions ‘BTS Overload Control’

Documentation released together with the SW in NOLS

Trang 10

CONFIDENTIAL

4 EFFECTS ON OPERATOR

4.1 Operability

Flexi EDGE BTS Operability is improved with the following corrections:

• NA05372623 Diffserv value of the PWE Tunnel at BTS can`t be set correctly

• NA05347098 BTS Manager application does not allow /30 mask for peer IP address

• NA05297378 Packet abis site restored only after giving ESMA HW power reset

5 APPENDICES / REFERENCES

None

Trang 11

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given “as is” and all liability arising

in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document

Nokia Siemens Networks will correct errors in this documentation as soon as possible IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws

The wave logo is a trademark of Nokia Siemens Networks Oy Nokia is a registered trademark of Nokia Corporation Siemens is a registered trademark of Siemens AG

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only

Trang 12

EX5 1.0.2 Release Upgrade Instructions

CONFIDENTIAL

Release Upgrade Instructions

Id: EX5 1.0.2 Product Family: Base Stations Product: Flexi EDGE Base Station Release: EX5

Trang 13

CONFIDENTIAL

Table of Content

1.Overview 3

1.1 Other Relevant Installation Instructions 3

2.BSC Preparations 4

2.1 Starting a MML session at the BSC 4

2.2 Checking the existing BTS SW 4

2.3 Making a safe copy of the active package 4

2.4 Copying the BTS SW from NOLS to the BSC 4

2.4.1 Downloading files from NOLS to the PC 4

2.4.2 Copying the BTS SW from PC to BSC with FTP 5

2.4.3 Creating the BTS SW 5

2.5 Previous deliveries for the release 6

3.Downloading the BTS Software 6

3.1 BTS Software downloading using the BSC 6

3.2 BTS Software downloading using NETACT 8

3.2.1 Uploading the BTS SW to Netact 8

3.2.2 Importing the BTS SW to Netact 11

3.2.3 Downloading the BTS SW from Netact 14

3.3 BTS SW downloading using the 2G Flexi BTS Manager 16

4.Activating the BTS Software 20

4.1 BTS Software activation using the BSC 20

4.2 BTS Software activation using NETACT 21

5.BTS Software Status handling using the BSC 22

5.1 Checking the existing BTS SW package consistency 22

5.2 Modifying BTS software status 23

5.3 Activating the Fallback 25

6.Special Conditions 26

7.Installing FlexiHub Manager SW 26

7.1 Installing FlexiHub Manager from CD-ROM 26

7.2 Installing FlexiHub Manager from NOLS 27

7.3 Uninstalling FlexiHub Manager 28

8.Updating FIFA software with FlexiHub Manager 28

9.Appendices / References 30

Contact:

Contact your local Nokia Siemens Networks support or GSM/EDGE BTS Technical

Support: bts.technicalsupport@nsn.com

Summary of changes:

Trang 14

CONFIDENTIAL

Purpose

The purpose of this document is to describe the actions needed for installing this Release

Delivery into the customer’s network

1 OVERVIEW

This is an overview of how to install the Nokia Siemens Networks Flexi EDGE Base Station

software (BTS SW) EX5 1.0.2 SW Delivery

The following processes are detailed in this document

1 Installation, creation, verification and activation of the BTS SW package at the BSC

2 Installation and background downloading of BTS SW using NetAct OSS5.2 MP1.0

3 Downloading of BTS SW using the 2G BTS Site Manager application

4 Installation and upgrade of FIFA SW

Note that all the file names and file extensions and screenshots serve as examples only For

correct BTS SW file names and file extensions, see the Release Note

Before you start

Make sure that all the required licenses are installed at the BSC before activating the BTS SW

For instructions on how to install transmission licenses, see Activating and testing 2G Flexi

Abis over IP/Ethernet, 2G Flexi Additional 2 E1/T1, 2G Flexi TRS Abis Grooming and 2G Flexi

TRS Loop Protection in the BSC and TCSM, RG20 Operating Documentation Set

Terminology throughout this document

A BTS site is referred to as a BCF

The BTS software package is loaded into the BCF object and it is called BTS Software or BTS

SW

The MML commands where user definable input is required are presented in Bold and Italics

1.1 Other Relevant Installation Instructions

None

Trang 15

1 Enter username: <Username>

2 Enter password: <Password>

2.2 Checking the existing BTS SW

Steps

1 List the existing BTS SW packages and their locations with the MML command:

ZEWL;

2 Select the first /BCF_PACK/PACK_X directory that is not listed

PACK_x is a sub-directory of the /BCF_PACK directory In these instructions, PACK_1 is used

as an example directory

3 Verify that PACK_1 is empty with the following MML command:

ZIWX::WS,NODEF:BCF_PACK,PACK_1:%,%,;

If no files are listed when giving this command, you can use the PACK_1 directory Otherwise,

delete the files listed or select another directory

4 If there are files in the directory, delete them with the following MML command:

2.3 Making a safe copy of the active package

The active default BTS SW package attached to BCF is not removed from the BSC hard disk

when activating the new SW packet Thus no separate actions are needed to create a safe

copy from BTS SW package

2.4 Copying the BTS SW from NOLS to the BSC

2.4.1 Downloading files from NOLS to the PC

Purpose

Trang 16

1 Create a directory on your PC where you can download and extract the BTS SW files

2 Go to NOLS homepage at https://online.portal.nokiasiemensnetworks.com with your

browser and log in by using your NOLS username and password

3 Follow this path to locate Flexi EDGE BTS SW: Care – Software Delivery – Base

Stations – Flexi EDGE Base Station

4 Select the correct Release, Change Delivery or New functionality tab depending on the

SW version you are looking for

5 Click the correct SW title

6 Select Software and Document files Then select Download

7 Save the zip file(s) into a local folder on your PC

8 Select NOLS Logout

9 Open the zip file(s) and extract them

2.4.2 Copying the BTS SW from PC to BSC with FTP

The BSC must be connected to the same LAN (Local Area Network) as the PC with the downloaded files

Note that the TCP/IP feature must be activated in the BSC before you can use these instructions The BSC IP address must be known by the user when using the FTP program

1 To create the BTS SW that was just copied in section Copying the BTS SW , give the

following MML command to create a BCF SW Build:

ZEWC:BTSSWxxxx:MF=BTSE4203,EXT=B4X,SDIR= PACK_1;

Trang 17

CONFIDENTIAL

where

• BTSSWxxxx is the name you give to the BTS SW

• BTSE4203 (or equivalent) is the name of the master file on the diskette

• B4X (or equivalent) is the extension part of the master file name on the

diskette

• PACK_1 is the sub-directory that the package was copied to in section

Copying the BTS SW from magneto-optical disks to the BSC hard disks

Further information

The content of the BTS SW package can be checked with the following MML command:

ZEWP:ID=<bts_SW_name>;

For the actual BTS SW file names, see the Release Note

2.5 Previous deliveries for the release

EX5 1.0.2 SW Delivery and its installation does not require any previous SW deliveries EX5 1.0.2 can be installed where EX3.1 (and any MPs or PPs) may already

be active in a BTS site

However, compatibility restrictions must be checked for minimum BSC SW level before starting the EX5 1.0.2 update More information can be found from reference /1/

3 DOWNLOADING THE BTS SOFTWARE

3.1 BTS Software downloading using the BSC

Before you start, note:

The BCF must be operational in order to download the new BTS SW package The BTS SW is downloaded as a background operation from the BSC and this does not have any effect on the ongoing BTS operation

Steps

1 Start a remote service terminal session from the BSC to the BCF with the following

MML command:

ZDDS;

2 Create a service terminal application if it does not exist yet, and enable it with the

service terminal command:

00-MAN> ZLE:X,RPHASESX

00-MAN> X

3 Monitor the BCF with the following service terminal command:

00-RPH> DC: <bcf_number>

Trang 18

CONFIDENTIAL

Where

• D stands for monitoring

• C stands for continuously

• <bcf_number> is the site-specific BCF number

(use Ctrl +C to exit monitoring then type ZE to exit the remote service terminal session when required)

4 If the BCF is operational, start background downloading the BTS SW with the following

For correct file names and file extensions see reference /2/

Figure 1 Monitoring the BTS SW downloading After downloading the BTS will store the new BTS SW package into flash memory

Unexpected outcome

If the BCF is in reset, the BTS SW background downloading cannot take place

If the BCF is in reset, or if it is reset before the new BTS SW is activated (see section

Activating the BTS SW), the old BTS SW is downloaded as it is still the default BTS

SW

Trang 19

CONFIDENTIAL

3.2 BTS Software downloading using NETACT

3.2.1 Uploading the BTS SW to Netact

Steps

1 Log into the System Server as an approved user (take a Telnet session into the NetAct server)

Figure 2 FTP client login

2 Check for free space under the path /d/ossvar by entering the following command

% bdf /d/ossvar

Make sure that there is enough free disk space for the new BTS SW package

3 Go to the /swtemp directory with the following command

% cd /var/opt/nokia/oss/global/swmgmt/swtemp

Trang 20

CONFIDENTIAL

Figure 3 BTS software listing

4 Create a new temporary sub-folder for the BTS SW package by entering the following

command (EX42 as a sub-folder name shown as the example)

% mkdir EX42

5 Copy (with an FTP client) all the BTS SW release application files to this sub-folder

Use Binary mode to FTP the files

Figure 4 FTP Binary mode

Trang 21

CONFIDENTIAL

Figure 5 Copying Progress

6 Change the permission set of the sub-folder and BTS SW package files by entering

the following command (use the correct sub-folder name, EX42 shown as the example)

% chmod -R 777 EX42

Trang 22

Trang 23

CONFIDENTIAL

Figure 7 Netact Start Page

2 Click the Software Manager icon

3 Select the SW Archive tab

4 Select the NE Type as BCF and sub-type as Flexi EDGE

Figure 8 Software Archive

5 Click Import New SW Package

6 From the list, double-click the temporary sub-folder you created earlier

Trang 24

CONFIDENTIAL

7 Select all the BTS SW package files under the temporary sub-folder

Figure 9 Import SW Package

8 Enter a name for the SW package

The name should consist of only upper case letters, numbers, and underscore

9 Click Import

Figure 10 Import Success

Trang 25

% rm -rf % cd /var/opt/nokia/oss/global/swmgmt/swtemp/EX42

3.2.3 Downloading the BTS SW from Netact

Steps

1 From the NetAct start page, select the Administration folder

2 Click the Software Manager icon

3 Select the Network SW Status tab

4 Select the NE Type as BCF and sub-type as Flexi EDGE

5 Select the parent BSC for the desired BCF displayed in the Parent View

6 In the Network Elements table, select the check box(es) for the desired BCF(s)

7 Select the New Task tab

8 Select 'Download' from the Task Type drop-down menu

9 Select 'SW' from the SW Type drop-down menu

Trang 26

CONFIDENTIAL

10 Select the correct SW package from the SW Package drop-down menu

Figure 12 SW Task

11 The download task can be started immediately or as a scheduled task Select this by

clicking the 'Schedule' button and then selecting the desired option from the Frequency drop-down menu

12 Progress can be monitored via the Tasks tab

Figure 13 Ongoing Tasks

Trang 27

CONFIDENTIAL

3.3 BTS SW downloading using the 2G Flexi BTS Manager

Download a new software package from 2G Flexi BTS Site Manager only when there

is no Abis connection, or when the BCF object at the BSC does not have an active BTS software package attached to it or if the RFM software requires updating If the BCF object at the BSC has a default software package attached, it overrides the locally downloaded BTS software You can check this with the following MML command, which should show no default software package:

ZEWO:<bcf number>;

For instructions on firewall settings, see Installing Nokia 2G Flexi BTS Site Manager in

Flexi EDGE BTS Commissioning document

For instructions on the IP address settings, see section Changing IP address settings

with Windows XP

Steps

1 Start the 2G Flexi BTS Site Manager by clicking the 2G Flexi BTS Site Manager desktop icon or navigating from the Windows Start Menu to All Programs -> Nokia Siemens Networks -> BTS Site – 2G Flexi BTS Site Manager

Figure 14 2G Flexi BTS Site Manager Start Up

2 Press Connect in the Local Connection tab

Additional Information

Trang 28

CONFIDENTIAL

The 2G Flexi BTS Site Manager launcher begins with a compatibility check The BTS software version is verified and if multiple versions are installed, the most appropriate version of the 2G Flexi BTS manager application is started

Figure 15 2G Flexi BTS Site Manager Compatibility check

3 Go the BTS SW pull-down menu and select SW Update

Trang 29

CONFIDENTIAL

Figure 16 BTS SW Update with BTS Manager

4 Select the correct master file name by clicking the Master File button

Note that the master file name always starts with 'BTS', for example 'BTSM4203.B4X'

Trang 30

download all application files from the BTS Manager, select the Force BTS to

download All Application Files check box

5 Click the Update SW button

Expected outcome

The new master file and application files will be downloaded to the BTS

After the download is completed, the site undergoes a reset, and after recovery, starts

to operate with the new BTS software

Trang 31

CONFIDENTIAL

4 ACTIVATING THE BTS SOFTWARE

4.1 BTS Software activation using the BSC

Before you start, note

If the BTS software build includes updates to the transmission software, activating the BTS software may temporarily disrupt any hub traffic passing through the BTS site

For correct file names and file extensions see reference /2/

Figure 18 Monitoring the BTS SW activation process

The new BTS SW is now the default BTS SW with the status NW (New) at the BSC

The BCF is reset and upon restart the new BTS SW package is taken into use The BTS SW packages attached to the BCF can be checked with the following MML command:

ZEWO: <bcf_number>;

The screen should look like in the example printout below

Trang 32

CONFIDENTIAL

Figure 19 Checking the BTS SW packages attached to the BCF

4.2 BTS Software activation using NETACT

Steps

1 Follow the steps given in the section Downloading BTS SW from NetAct to BCF

2 Instead of the 'Download task in step 8, choose the “download_activation” from the

drop down menu

Trang 33

CONFIDENTIAL

5 BTS SOFTWARE STATUS HANDLING USING THE BSC

5.1 Checking the existing BTS SW package consistency

Steps

1 List the existing BTS SW packages and their locations with the MML command:

ZEWL;

2 Select the first /BCF_PACK/PACK_X directory that is not listed

Remember that the BTS SW will be located there

Pack_X is a sub-directory of the /BCF_PACK directory In these instructions, PACK_1 is used

as an example directory

3 Verify that PACK_1 is empty with the following MML command:

ZIWX::WS,NODEF:BCF_PACK,PACK_1:%,%,;

If no files are listed when giving this command, you can use the PACK_1 directory Otherwise,

delete the files listed or select another directory

4 If there are files in the directory, delete them with the following MML command:

ZIWD::WS,NODEF:BCF_PACK,PACK_1:file_name,file_extension,;

where file_name is the name of the file you are deleting and file_extension is the extension of that file

5 To delete both source and backup files, give the following MML command:

ZIWD::WSB,NODEF:BCF_PACK,PACK_1:file_name,file_extension;

Trang 34

CONFIDENTIAL

5.2 Modifying BTS software status

There can be up to three BTS SW packages present in the BTS Site, identified as

"Running", "Active" and "Standby" The "Running" package is the SW that is currently running in the BTS, and the "Active" and "Standby" packages are the SWs that are stored in the BTS Site's FLASH memory (note that only two SW packages are stored

in FLASH memory at any time) The "Active" SW package is the SW that will be run (that is, becomes the "Running" package), at the next BTS restart, although it should

be remembered that the BSC can download a new "Active" SW package during the start-up sequence

There can be up to three BTS SW packages assigned to a BCF in the BSC These are

"NEW" (NW), "BACKUP" (BU) and "FALLBACK" (FB) Standard practice is that new BTS software is given NW status, and only when the new software acceptance is given the FB is cleared, the BU is swapped to FB and NW is swapped to BU The default package at the BSC determines what BTS software the BTS will start with after

a reset Downloading of a SW package only occurs if the BTS does not already have the package stored in the BTS FLASH memory

Use the following BTS SW statuses:

• 'New' should contain no BTS SW

• 'Backup' should contain the default BTS SW

• 'Fallback' should contain another BTS SW if one exists

Now the default BTS SW has the 'Backup' status

3 Detach the BTS SW with the 'New' status with the following MML command:

ZEWE:<bcf_number>:NW;

4 Display the BTS SW packages that are attached to the BCF with the following MML

command:

ZEWO:<bcf_number>;

Trang 35

Trang 36

CONFIDENTIAL

5.3 Activating the Fallback

Before you start, note

If the BTS software build includes changed transmission software, activating the BTS software may temporarily disrupt any hub traffic passing through the BTS site

Trang 37

CONFIDENTIAL

6 SPECIAL CONDITIONS

None

7 INSTALLING FLEXIHUB MANAGER SW

7.1 Installing FlexiHub Manager from CD-ROM

Check the following before starting the installation

• You have FlexiHub Manager on CD-ROM or access to NSN Online Services (NOLS) at https://online.portal.nokiasiemensnetworks.com

• Your computer meets the system requirements given in System requirements

for FlexiHub Manager under Descriptions - Management - Performance

Management in Product Description for FIFA Flexbus Transmission module for Nokia Siemens Networks Flexi EDGE BTS

Sub-• Windows 2000, Windows XP, or Windows 2003 server has been correctly installed on your PC

• You are familiar with the version of Windows you are using

• You have administrator rights if you are using Windows 2000, Windows XP or Windows 2003 server operating system

• GCS (General Communication Services) has been installed on your PC

• You are aware of other NMS/10-compliant manager products installed on your

PC

Steps

1 Start Windows Close all other applications before installing FlexiHub Manager

2 Insert the CD-ROM into the drive

3 If the autoplay function is activated

d) Find the CD-ROM drive, look for the file FlexiHubSetup.exe and double-click it

The file name may include version information You are back in the Run dialogue box

e) Click OK The installation program starts From the program you can choose to

read the installation notes or install the manager

4 Click Install and follow the on-screen instructions

5 If GCS is not already installed on your PC, install it by executing step 3 using GCS

R5\Setup.exe

Trang 38

CONFIDENTIAL

7.2 Installing FlexiHub Manager from NOLS

Check the preconditions for installation from Installing FlexiHub Manager from

CD-ROM

Steps

1 Start Windows Close all other applications before installing FlexiHub Manager

2 Extract the installation package that was downloaded from NOLS to a temporary

location in your computer

3 Locate the file FlexiHubSetup.exe in the installation root directory and double-click it to

start the installation program The file name may include version information

4 Click Install and follow the on-screen instructions

5 Install GCS if it is not already installed on your PC

You can also obtain the latest GCS from Nokia Online Services (NOLS)

Trang 39

CONFIDENTIAL

7.3 Uninstalling FlexiHub Manager

Steps

1 Open the Windows Control Panel

2 Use Add/Remove Programs to remove the manager

For further information, see Windows documentation

Note that removing FlexiHub Manager does not remove any data files you have created Because of this, the Manager directory structure may not be removed either

If you wish to remove GCS as well, then a separate operation must be performed

Note that GCS is a common component required by all element managers using Q1

8 UPDATING FIFA SOFTWARE WITH FLEXIHUB MANAGER

Purpose

The Nokia FlexiHub Manager Software View is used to manage the software

configuration of the network element:

• Viewing the installed software version,

• Downloading a software file to a unit,

• Activating the software

1 Connect to Flexi EDGE FIFA

For more information about connecting locally or remotely, see Connecting locally

or Connecting remotely in Administering FIFA Flexbus Transmission Sub-module

for Nokia Flexi EDGE BTS

2 Upgrade software

a) Select Software from the View Bar or from the View menu The Software

View opens

Trang 40

CONFIDENTIAL

Figure 21 FIFA Module Software View

b) In the Software View, select the network element from the list

c) Check the Update check box

d) Select a software package from Available Software Versions list or

Browse to locate the package

3 Click Update Progress bar shows the status as "Downloading" during sw update

When the software package update is completed, new sw is visible as Inactive

Software

4 Activate the updated software

a) Select Software from the View Bar or from the View menu

b) In the Software View, select the software unit from the list

c) Check the Activate check box

d) Click Activate to activate the updated software

The inactive software becomes the Active Software

Software download does not cause a traffic interruption, but it slows down the management connection to the node Traffic may be cut when new software is activated if the respective unit is reset The activation can take several minutes

Định dạng
Số trang	233
Dung lượng	2,81 MB
File đính kèm	172970188-Alcatel-BTS-Hardware-Description.zip (13 MB)