76 8600 50143g 8600 smart routers performance counters reference guide

About This ManualThis chapter discusses the objectives and intended audience of the, 8600 Smart Routers Performance Counters Reference Guide and consists of the following sections: This

8600 Smart Routers Performance Counters Reference Guide

76.8600-50143G 28.04.2015

Revision History

76.8600-50143G 28.04.2015 FP7.0 updates for the following network elements:

• 8609 Smart Router and 8611 Smart Router FP2.0

• 8615 Smart Router FP1.0

• 8630 Smart Router and 8660 Smart Router FP5.0Supported cards are specified per counter for 8630 Smart Routerand 8660 Smart Router

76.8600-50143E 13.05.2014 Updates added for:

• 8602 Smart Router FP1.0

• 8609 Smart Router and 8611 Smart Router FP1.3

This revision of the manual documents the following network elements and the correspondingfeature packs or higher.

The functionality described in this document for 8615 Smart Router is also applicable to 8615 Smart Router stacked, unless otherwise stated.

© 2015 Coriant All rights reserved.

This manual is protected by U.S and international copyright laws, conventions and treaties Your right to use this manual is subject to limitations and restrictions imposed by applicable licenses and copyright laws Unauthorized reproduction, modification,

distribution, display or other use of this manual may result in criminal and civil penalties.

The specifications and information regarding the products in this manual are subject to change without notice All statements, information, and recommendations in this manual are believed to be accurate but are presented without warranty of any kind,

express or implied Users must take full responsibility for their application of any products.

Adobe ® Reader ® are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.

AIS Alarm Indication SignalANSI American National Standards InstituteAPS Automatic Protection SwitchingATM Asynchronous Transfer ModeB8ZS Bipolar 8-Zero Substitution

BW BandwidthCBR Constant Bit RateCESoPSN Circuit Emulation Service over Packet-Switched NetworkCFO Content Free Operation

CLI Command Line Interface

CP C-bit ParityCRC Cyclic Redundancy Check

CU Control functionality (used in 8615 Smart Router and 8665 Smart Router)DS1 Digital Signal level 1 (T1)

DS3 Digital Signal level 3 (T3)DSL Digital Subscriber LineE1 E-carrier in ETSI

ES Error SecondsESF Extended Super FrameETSI European Telecommunications Standards Institute

FC Failure CountFEBE Far End Block Error

FP Feature PackHDB3 High Density Bipolar 3-zeroesLOPS Loss of Packet SynchronizationLOS Loss of Signal

MSP Multiplexer Section Protection

NE Network ElementOOFS Out Of Framed SecondsP12x Unframed 2.048 kbps according to G.703PCR Peak Cell Rate

PDH Plesiochronous Digital Hierarchy

PM Performance MonitoringPWE3 Pseudo Wire Emulation Edge to EdgeREI Remote Error Indication

SAToP Structure-Agnostic Time Division Multiplexing over PacketSCR Sustainable Cell Rate

SDH Synchronous Digital HierarchySEF Severely Errored FramingSES Severely Errored Seconds

SF Super FrameSHDSL Single-Line High-bit-rate Digital Subscriber LineSONET Synchronous Optical Network

STS Synchronous Transport SignalSU1 Switch unit in 8665 Smart RouterT1 T-carrier in ANSI

TDM Time Division MultiplexingUAS Unavailable SecondsUBR Unspecified Bit RateVBR Variable Bit Rate

VC ATM Virtual ChannelVCC Virtual Channel Connection

Table of Contents

Table of Contents

About This Manual 8

Objectives 8

Audience 8

8600 Smart Routers Technical Documentation 8

Document Conventions 12

Documentation Feedback 12

8600 Smart Routers Discontinued Products 13

1 Performance Counters 14

1.1 Overview 14

1.2 Interface DSL Counters 14

1.2.1 Shdsl Segment Endpoint 14

1.3 Interface Ethernet Counters 15

1.3.1 Cfm Delay Measurement 15

1.3.2 Cfm Loss Measurement 17

1.4 Interface PDH Counters 18

1.4.1 Ds1 Line 18

1.4.2 P12 / Ds1 Path 19

1.4.3 Tdm Pw 20

1.4.4 Ds3 Path 22

1.4.5 Abis Group 24

1.5 Interface SDH Counters 26

1.5.1 Rs 26

1.5.2 Ms 27

1.5.3 Sts / Vt15 Path 28

1.6 Layer 2 Tunneling Counters 29

1.6.1 Pwe3 Circuit 29

1.7 Node Testing and Measurement Counters 30

1.7.1 Power Consumption 30

1.7.2 CPU / Cache / Memory 31

1.7.3 NPU 32

About This Manual

This chapter discusses the objectives and intended audience of the, 8600 Smart Routers

Performance Counters Reference Guide and consists of the following sections:

This reference manual is intended for system specialists and personnel involved in network planning

8600 Smart Routers Technical Documentation

The document numbering scheme consists of the document ID, indicated by numbers, and thedocument revision, indicated by a letter The references in the Related Documentation table beloware generic and include only the document ID To make sure the references point to the latestavailable document versions, please refer to the relevant product document program on the Tellabsand Coriant Portal by navigating towww.portal.tellabs.com> Product Documentation & Software

> Data Networking > 8600 Smart Routers > Technical Documentation

The table below reflects the customer document content planned for SR7.0 GA, and is subject tochange Before General Availability of SR7.0, the configuration guides have the status of draft, andthey do not always describe the full functionality

About This Manual

8600 Smart RoutersATM and TDM Configuration Guide(76.8600-50110)

Provides an overview of 8600 NEs PWE3 applications,including types, Single-Segment and Multi-Segment; PWE3Redundancy; ATM applications, including PWE3 tunnelling,Traffic Management, Fault Management OAM, protection andTDM applications as well as instructions on how to configurethem with CLI

8600 Smart RoutersBoot and Mini-ApplicationsEmbedded Software Release Notes(76.8600-50108)

Provides information related to the boot and mini-applicationssoftware of 8605 Smart Router, 8607 Smart Router, 8609Smart Router, 8611 Smart Router, 8620 Smart Router, 8630Smart Router and 8660 Smart Router as well as the installationinstructions

8600 Smart RoutersCLI Commands Manual(76.8600-50117)

Provides commands available to configure, monitor and maintain

8600 system with CLI

8600 Smart RoutersEmbedded Software Release Notes

8600 Smart Routers SR7.0 Embedded Software Release Notes(76.8670-50177) for the following products:

Provides an overview of 8600 system HW inventory, softwaremanagement, equipment protection 1+1 (CDC and SCM) as well

as instructions on how to configure them with CLI

8600 Smart RoutersEthernet Configuration Guide (76

8600-50133)

Provides an overview of 8600 system Ethernet applications,including interfaces; Ethernet forwarding (MAC Switching,Ethernet PWE3, IRB, VLAN, VPLS); Ethernet OAM; LAG;ELP as well as instructions on how to configure them with CLI

8600 Smart Routers Smart RoutersFault Management ConfigurationGuide (76.8600-50115)

Provides an overview of 8600 system fault management,including fault source, types and status as well as instructions onhow to configure it with CLI

8600 Smart RoutersFrame Relay Configuration Guide(76.8600-50120)

Provides an overview of 8600 system Frame Relay applications,including interfaces; Performance Monitoring; protection; TrafficManagement as well as instructions on how to configure themwith CLI

8600 Smart RoutersHardware Installation Guide(76.8600-40039)

Provides guidance on mechanical installation, cooling,grounding, powering, cabling, maintenance, commissioning andESW downloading

Document Title Description

8600 Smart RoutersNetwork Interfaces ConfigurationGuide

The Network Interfaces Configuration Guide provides anoverview of the 8600 NEs interface functions, including NEsupported interface types and equipping; interface features;configuration options and operating modes; fault management;performance monitoring; interface configuration layers and portprotocols as well as instructions on how to configure them withCLI The following interface configuration guides are available:

• 8600 Smart Routers Network Interfaces ConfigurationGuide (76.8600-50161) (for 8602 Smart Router, 8615 SmartRouter and 8665 Smart Router)

• 8609 Smart Router and 8611 Smart Router FP7.0 InterfaceConfiguration Guide (76.8670-50179)

• 8600 Smart Routers FP7.0 Interface Configuration Guide(76.8670-50180) (for 8630 Smart Router and 8660 SmartRouter)

8600 Smart Routers

IP Forwarding and TrafficManagement Configuration Guide(76.8600-50122)

Provides an overview of 8600 NEs IP, forwarding and trafficmanagement functionality, including: IP addressing; IP hosting(ARP, DHCP); IP routing (static); ACL; Differentiated Services(Policing, Queue Management, Shaping) as well as instructions

on how to configure them with CLI

8600 Smart RoutersManagement CommunicationsConfiguration Guide

(76.8600-50125)

Provides an overview of 8600 system managementcommunications functions, including communication protocols:BMP; FTP; RADIUS; SNMP; SSH; TELNET as well asinstructions for configuring them with CLI

8600 Smart RoutersMobile Optimization ConfigurationGuide (76.8600-50100)

Provides an overview of 8600 system Mobile Optimizationapplications as well as instructions on how to configure themwith CLI

8600 Smart RoutersMPLS Applications ConfigurationGuide (76.8600-50123)

Provides an overview of 8600 NEs MPLS applications (includingFRR (one-to-one and facility backup); LDP; protection andTraffic Engineering), MPLS-TP applications (including OAM,linear protection), S-MPLS applications as well as instructions

on how to configure them with CLI

8600 Smart RoutersPerformance Counters ReferenceGuide (76.8600-50143)

Provides an overview of 8600 system supported performancecounters

About This Manual

8600 Smart RoutersReference Manuals The reference manuals describe the 8600 network elementfeatures including:

• NE enclosure, baseboard, power supply modules, andinterfaces in 8602 Smart Router FP7.0 Reference Manual(76.8670-40130)

• NE enclosure, baseboard, power supply modules, interfacesand physical LM types in 8609 Smart Router FP7.0 Refer-ence Manual

• NE enclosure, baseboard, power supply modules, SCMs, HMand LM types in 8611 Smart Router FP7.0 Reference Manual

• NE enclosure, baseboard, power supply modules, and faces in 8615 Smart Router FP7.0 Reference Manual

inter-• NE subrack, fan modules, CDCs, line cards and IFMs in 8630Smart Router FP7.0 Reference Manual

• NE subrack, fan modules, CDCs, line cards and IFMs in 8660Smart Router FP7.0 Reference Manual

• NE subrack, fan modules, line unit and switch unit in 8665Smart Router FP7.0 Reference Manual (76.8670-40128)

8600 Smart RoutersRouting Protocols ConfigurationGuide (76.8600-50121)

Provides an overview of 8600 NEs routing protocols, includingBFD; BGP; BGP MP; ECMP; IS-IS; OSPF and VRRP as well asinstructions on how to configure them with CLI

8600 Smart RoutersSNMP MIB Support(76.8600-50116)

Describes SNMP MIB support by the 8600 NEs and providesinformation on the supported objects and traps For furtherinformation on SNMP MIBs, see the related RFCs

8600 Smart RoutersStatistic Counters Reference Guide(76.8600-50142)

Provides an overview of 8600 system supported statistic counters

8600 Smart RoutersSynchronization ConfigurationGuide (76.8600-50114)

Provides an overview of 8600 NEs synchronization functionality,including physical layer Frequency Synchronization (SEC, EEC);PTP Frequency Synchronization; Phase-Time Synchronization(L2 and L3 applications) as well as instructions on how toconfigure them with CLI

8600 Smart RoutersTest and Measurement ConfigurationGuide (76.8600-50124)

Provides an overview of 8600 NEs measurement and connectivityverification tools, including Ethernet loopback; IP ping andtraceroute; MAC swap loopback; MPLS ping and traceroute;PLT; PWE3 loopback; VCCV (BFD, LSP ping) as well asinstructions on how to configure them with CLI

8600 Smart RoutersVPNs Configuration Guide(76.8600-50128)

Provides an overview of 8600 system virtual private network(VPN) layer 3 applications as well as instructions on how toconfigure them with CLI

8000 Intelligent Network ManagerOnline Help

Provides instructions on how different operations are performedwith the 8000 Intelligent Network Manager Describes alsodifferent parameters and controls of the 8000 Intelligent NetworkManager dialogs and windows

Note that the Online Help is not available on the Portal but it isincorporated in the 8000 Intelligent Network Manager

Document Conventions

This is a note symbol It emphasizes or supplements information in the document.

This is a caution symbol It indicates that damage to equipment is possible if the instructions are not followed.

This is a warning symbol It indicates that bodily injury is possible if the instructions are not followed.

Documentation Feedback

Please contact us to suggest improvements or to report errors in our documentation:

Email: fi-documentation@tellabs.com

8600 Smart Routers Discontinued Products

8600 Smart Routers Discontinued Products

8600 Smart Routers Manufacture Discontinued (MD) notifications are available on the Tellabsand Coriant Portal,www.portal.tellabs.com > Product Documentation & Software > Data Networking > [8600 Smart Router product name] > Product Notifications.

1 Performance Counters

1.1 Overview

In the following tables there are presented performance counters supported by the 8600 productfamily NEs All performance counters are accessible in both CLI and BMP, whereas SNMP supportsonly subset of them Those are mentioned in performance counter description Performancecounters are counters that count for specific time-intervals only (typically 15 minutes or 24 hours),after which they are moved to history records In addition to current records, there are typically

31 15-minutes and 1 24-hour history records

Only actual counters are shown in this document, not additional record information, like start times

The BMP Counter column contains performance counter name in BMP protocol Due to historical

reasons, the counter name may slightly differ in some cases in CLI or INM

The Description column describes the performance counter SNMP equivalency is mentioned when

also SNMP access is supported in 8600 product family NEs

The Support ([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] / 8620 / 8602 / 8605 / 8607 /

8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1]) column identifies the Feature Pack (FP) numbers

indicating the first release where the counter is supported (support is continued in next releases),separated by slashes (/) Dash (-) means that the NE does not support the counter

• The first FP numbers in brackets relate to 8630 Smart Router and 8660 Smart Router FP numbersare shown per unit

• The second FP number relates to 8620 Smart Router

• The third FP number relates to 8602 Smart Router

• The fourth FP number relates to 8605 Smart Router

• The fifth FP number relates to 8607 Smart Router

• The sixth FP number relates to 8609 Smart Router

• The seventh FP number relates to 8611 Smart Router

• The eighth FP number relates to 8615 Smart Router

1 Performance Counters

CLI: show interface performance

([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] /

8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1])

es (nearEnd) Count of Errored Seconds (ES) FP [ / / / / ] /

/ / / 1.0A / / / [- / - / -]

-ses (nearEnd) Count of Severely Errored Seconds (SES) FP [ / / / / ] /

/ / / 1.0A / / / [- / - / -]

-uas (nearEnd) Count of Unavailable Seconds (UAS) FP [ / / / / ] /

/ / / 1.0A / / / [- / - / -]

-crcAnomalies (nearEnd) Count of CRC anomalies FP [ / / / / ] /

/ / / 1.0A / / / [- / - / -]

-losws (nearEnd) Count of Loss of Sync Word (LOSW)

CLI: show eth cfm mp dm

([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] /

8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1])

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

BMP Counter Description Support

([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] /

8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1])

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

below which the measured values fall

Only applies to history PM and does notapply to current PM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

below which the measured values fall

Only applies to history PM and does notapply to current PM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

below which the measured values fall

Only applies to history PM and does notapply to current PM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

below which the measured values fall

Only applies to history PM and does notapply to current PM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

Variation

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

Variation FP [- / - / - / 3.1 / -] /- / 1.0 / 1.5 / - / 1.0 /

1.1 / - [- / - / -]

neLowPercIfdv Near-end Low Percentile Delay FP [- / - / - / 3.1 / -] /

1 Performance Counters

([8660,8630 CDC1 / CDC2 / IFC1 / IFC2 / ELC1] /

8620 / 8602 / 8605 / 8607 / 8609 / 8611 / 8615 / [8665 vCU / LU1 / SU1])

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

below which the measured values fall

Only applies to history PM and does notapply to current PM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

below which the measured values fall

Only applies to history PM and does notapply to current PM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

Variation

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

Variation FP [- / - / - / 3.1 / -] /- / 1.0 / 1.5 / - / 1.0 /

1.1 / - [- / - / -]

feLowPercIfdv Far-end Low Percentile Delay Interframe

Delay Variation below which themeasured values fall Only applies tohistory PM and does not apply to currentPM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]

feHiPercIfdv Far-end Hi Percentile Delay Interframe

Delay Variation below which themeasured values fall Only applies tohistory PM and does not apply to currentPM

FP [- / - / - / 3.1 / -] /

- / 1.0 / 1.5 / - / 1.0 /1.1 / - [- / - / -]