Kirigami là nghệ thuật cắt giấy truyền thống của Nhật Bản, với tên gọi được ghép từ hai chữ : “kiru” (có nghĩa là cắt) và “kami” (là giấy). Tính đối xứng là đặc điểm nổi bật nhất trong kirigami truyền thống. Hình bông tuyết, ngũ giác, và bông hoa là những hình ảnh cổ điển quen thuộc đặc trưng cho kirigami mà trong đó, cắt giấy đơn thuần chỉ nhằm tôn lên cấu trúc tối giản, cân xứng nhưng cũng rất linh hoạt của thiết kế. Nghệ thuật cắt giấy được cho là lần đầu tiên xuất hiện trong các đền chùa Nhật Bản như một cách thể hiện lòng thành kính trước các vị thần. Đến khoảng thế kỷ XVII, Kirigami được biết đến rộng rãi khắp châu Á như một hình thức nghệ thuật đích thực. Không chỉ riêng ở Nhật mà cả ở Trung Quốc, người ta tạo nên các thiết kế kirigami để biểu trưng cho những điều tốt đẹp và quan trọng như: Thịnh vượng, Hoàn hảo, Quý phái, Trang nhã hay thậm chí là mối liên kết giữa con người và vũ trụ. Bunraku, một loại hình múa rối Nhật Bản đôi lúc cũng sáng tạo những con rối bằng giấy từ kỹ thuật Kirigami, nhưng vẫn đảm bảo các bộ phận có thể cử động được.
Trang 11 2 3
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold
Valley fold(dashed and dotted line)
Make a valley fold
Scissors line(solid line)
Cut along the line
Cut in line(solid line)
Cut along the line
Glue spot(Red dot)
Glue parts with the same shape together
Glue spot(Green dot)
Glue within the same part
Glue spot(Blue dot)
Glue to the rear of the other part
Glue The glue spot(colored dot) shows where to apply the glue.
Tools and materials
Assembly tip
Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff.
View of completed model
Assembly Instructions:Three A4 sheets(No.1 to No.3)
*This model was designed for Papercraft and may differ from the original in some respects
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order
http://www.canon.com/c-park/en/
be glued together (* This way, you can be sure which section is which even after cutting out
the sections.)
Glue the upper glue tabs of part 3
to the inside areas with circles on the printed side of part 4
Reverse side of part 4
Printed side of part 4
Carefully glue the lower glue tabs
of part 3 to the glue areas of part 1, one at a time
Trang 210
11 7
5
13 15
14
12 5+6+7+8+9
Glue parts 8 + 9 to the glue tabs
on the outside of parts 6 + 7
Top of part 5
Side of parts 6 + 7
Glue part 5 to the glue tabs inside parts 6 + 7
Glue part 5 and parts 6 + 7 together
so that the narrower side of parts 6 + 7
faces in the same direction as the area
of part 5 on which steps are printed
Glue part 11 to part 10 along
the circle on the inside of part 11
Glue part 10 to parts 5 - 9 along the circle on
the inside of part 5
When doing so, match the entrance printed on
part 10 to the steps printed on part 5
Make a cut along the red line from the edge and then cut out the center circle
Glue part 15 in place after assembling the stand
Trang 317
18 19
20 21 22
24 23
Glue part 16-24
to the top surface
Glue parts 1 - 4 together so that their columns are aligned
Refer to this illustration when inserting the tower into the stand