The complete chief officer 39 cargo holds

I think so and if I had the hatch tape and foam available, I would consider it a responsible decision to use it, not as a repair but as an additional measure of care of the cargo.. Certa

On any ship type, your cargo is the reason for the ship's existence The proper planning, loading, stowage, carriage and discharge should be the focus of all staff, after navigation and the safety of the ship and those onboard Paramount in this is where the cargo is stowed, in tanks, holds or on deck

Each year cargo is destroyed, damaged or contaminated by seawater entering the holds

of ships, both old and new The majority of these occurrences are on older ships, but

Incorrectly stowed cargo may not end up where it was intended

tops of the coamings will tell you the story, as will the state of the rubbers, drain channels and compression bars Signs of hatch sealing tape or foam sealant can also be a sign of potential leaking, although this is not necessarily a sign of poor hatch seals Your hatches are weathertight not watertight Submerge any hatch in water long enough and it will leak Hopefully this will not happen during your time onboard but there are times during bad weather when the ship takes heavy seas on the decks, particularly on the forward hatches If you are on an old ship, taking a grain cargo across the ocean in northern winter, would it not be prudent to take every care that you can of the cargo? I think so and

if I had the hatch tape and foam available, I would consider it a responsible decision to use it, not as a repair but as an additional measure of care of the cargo

39.1 The Testing of Hatch Covers

It would be easy to say that these should be tested before loading a cargo, but for ships

on short haul voyages it is usually unnecessary Before waiting for the annual loadline survey they should be tested periodically, on older ships more frequently than new ships Certainly if I was setting off on a grain voyage across the Atlantic on an old ship I would test my hatch tops very thoroughly indeed, not wishing to be faced with a green topping to the cargo at the other end

Most of us tend to use the hose test and there is nothing wrong with this provided it is done properly Consider the force of water hitting your hatch tops in a storm and then use your hose to try to emulate it You should ensure that your hatchtops are well battened down with the drain holes free and the non-return valves unblocked

When you use the hose make sure that it is directed at the seals around the hatch sides and along each seal on the top, with the nozzle close to the seal Try hard to get the water in!

Non-return valves are sometimes more of a hindrance With many of them being made of plastic they often get washed away in heavy weather or broken by various means

It is wise to keep a few spares in your stores but should you find that you are short you can attach a length of hose to the drain, put a 'u' bend in it and secure the hose end up under the hatch coaming Make sure the open end is below this though!

Another way of chocking is by using a chalk test This has to be done in very good weather at sea as it involves opening the hatch tops If done in port it could mean a delay

in cargo operations It is a test that takes longer than the hose test but it will give you a

39.2 Hatch Repair

Rubber seals harden over the years and, as they harden, they become less effective When you examine the rubbers and see heavy grooving it suggests that the bearing pads that your hatch rests on have become worn down, so the whole weight of the hatch

is now resting on the rubber seals These pads will need to be built back up to

specification

When repairing your seals you should not try to insert small pieces of rubber Rather, insert a longer length up to around 2 metres Remember to clean out the channel first and coat with a good anti-corrosive paint Clean the ends of the old rubber that the new rubber will butt onto to ensure that the adhesive will coat each end properly Skilled seafarers can scarf the rubbers to ensure a more secure joint However, it is

recommended by manufacturers that when the rubber seal is in need of repair the whole rubber length should be replaced, rather than just that

section In all my time at sea we have always repaired sections as not only have we never had enough rubber to replace the whole section, but time would often have precluded this Whether shipowners are prepared to accept the expense of this or allow skilled shore labour to be called in for this replacement, when only a small section of the rubber has been damaged, is also doubtful

When checking your cleats, ensure that the rubber washers are in place During any voyage the ship is working and will be flexing the decks and hatches, so periodically the crew have to tighten the cleats and this should be part of your weekly work list The rubber washers allow for the flexing and assist in keeping the cleats tight Cleats can disappear over the side during bad weather so make sure that you have spares Cleats should not

be bar tight as this will force the hatch rubbers down onto the compression bar too hard and cause damage to the rubbers

39.3 Monthly Check of Hatches

• Cover tops, undersides and side panels - check for corrosion or cracks

• sealing arrangements - check rubbers, compression bars, drainage channels and non-return valves

• hatch cleats and rubbers - check for missing, corroded or broken

• chains or wire pulleys

• guide rails and track wheels

• stoppers

• hydraulic system

• pontoon hinges and locking pins

• coamings, stiffeners and brackets - check for any sign of corrosion and cracking, particularly at the corners of the hold and the deck plating in the way

of the coaming

39.4 Ladders

Another strange custom of the sea is that if ladders are in holds or tanks then a certain amount of damage or corrosion is acceptable, yet if they are outside on deck where they can

be seen then they must be repaired

The most common damage that occurs in any hold on a dry cargo ship is to the ladders It is rare for any such ship, particularly a bulk carrier, not to have some

responsibility All too often damage to a ladder cannot be safely reached by ship's staff and this requires the use of scaffolding or a cherry-picker This means shore

equipment and labour and a delay in work while the repair is effected, none of which will make you popular with any operator Quite a few will delay repairing the ladders until the next dry dock if they can

If it is possible, for the safety of all and to protect the ship, the ladders should be inspected prior to arrival If it is not, then they should be inspected as soon as possible

on opening up the holds and before anyone uses them Most ships have ladders fore and aft in the holds and if a ladder is deemed to be unsafe then it must be clearly marked and closed off until repaired In a number of ports you can be helped in this as, owing to the general state of ships' hold ladders, they have a safety inspection before work commences and they will order any unsafe ladders to be closed off or repaired if required

While on this subject don't forget to do the same for your tank ladders as well Just because it is crew using them rather than shore labour does not make the safety requirement any less stringent

39.5 Lighting

Lighting in holds is a nuisance as, not only do you have to try to maintain it, but there is the danger of damage to the cabling and an ever present possible fire risk Even replacing light bulbs can be hazardous and in many ships where lighting is built in, after some years the fuses are pulled and portable cargo lighting is rigged from above The main requirement is that adequate lighting is provided for crew to work safely and,

to prepare for this, have the cargo lights, whether fixed or portable, checked before they are required If fixed lighting is present, even if it is working correctly, the fuses should always be pulled when the hatches are closed as a precaution against any electrical damage

You might find it wise, during your meeting with the supervisor before work in the hold commences, to state what checks have been made and request that, if there is any complaint or problem, the duty officer is notified so that he can arrange additional lighting

39.6 Completion of Loading or Discharge

Before you close the hatch you must ensure that all debris is clear of the channels and that the drains and non-return valves are clear Cargo is damaged on ship after ship because of these very simple checks are being overlooked in the hurry to close the hatches and sail It is better to spend an extra hour or two ensuring that any water that does leak in through the hatch rubbers can run freely down the channels and out of the drains