ENVIRONMENTAL ENGINEER’S MATHEMATICS HANDBOOK - CHAPTER 6 potx

The moving average can be determined as an arithmetic or geometric mean and for varying periods 5, 7, or 28 days.. Because the week is the period most commonly used in water/wastewater t

Trang 1

CHAPTER 6 Statistics Review

Despite the protestation of Disraeli that, “there are three kinds of lies: lies, damned lies, and statistics,” probably the most important step in any environmental engineering study is the statistical analysis of the results The principal concept of statistics is that of variation In conducting typical environmental studies, such as a biological sampling protocol for aquatic organisms, variation is commonly found Variation comes from the methods employed in the sampling process or, in this example, in the distribution of organisms Several complex statistical tests can be used to determine the accuracy of data results In this discussion, however, only basic calculations are reviewed

When talking statistics, we are usually estimating something on the basis of incomplete knowledge Maybe we can only afford to test 1% of the items in which we are interested, and we want to say something about the properties of the entire lot Perhaps we must destroy the sample by testing it

In that case, 100% sampling is not feasible because someone is supposed to get the items after we are done with them

The questions we are usually trying to answer are “What is the central tendency of the item of interest?” and “How much dispersion about this central tendency can we expect?” Simply put, the average or averages that can be compared are measures of central tendency or central location of the data

Basic statistical terms include the mean or average; the median; the mode; and the range:

value

L1681_book.fm Page 139 Tuesday, October 5, 2004 10:51 AM

Trang 2

140 ENVIRONMENTAL ENGINEER’S MATHEMATICS HANDBOOK

Example 6.1

Problem:

Given the following laboratory results for the measurement of dissolved oxygen (DO), ﬁnd the mean, median, mode, and range Data: 6.5 mg/L; 6.4 mg/L; 7.0 mg/L; 6.9 mg/L; 7.0 mg/L

Solution:

To ﬁnd the mean:

To ﬁnd the mode and median, arrange in order: 6.4 mg/L; 6.5 mg/L; 6.9 mg/L; 7.0 mg/L; 7.0 mg/L

To ﬁnd the range:

The importance of using statistically valid sampling methods cannot be overemphasized; several different methodologies are available A careful review of these methods (with the emphasis on designing appropriate sampling procedures) should be made before computing analytic results Using appropriate sampling procedures along with careful sampling techniques provides accurate basic data

The need for statistics in environmental engineering is driven by the discipline As mentioned, environmental studies often deal with entities that are variable If no variations occurred in envi-ronmental data, no need for statistical methods would occur Over a given time interval, some variation in sampling analyses will occur Usually, the average and the range yield the most useful information For example, in evaluating the performance of a wastewater treatment plant, a monthly summary of ﬂow measurements, operational data, and laboratory tests for the plant would be used

6.4 DMR CALCULATIONS

Environmental engineers in charge of wastewater treatment facilities (typically plant or system managers) are responsible under state and federal national pollutant discharge elimination system (NPDES) permit requirements to oversee proper data recording in the daily monitoring report (DMR) In this section, we describe many of these calculations

(6.1)

Mean = (6.5 mg/L + 6.4 mg/L + 7.0 mg/L + 6.00 mg/L + 7.0 mg/L)

5

= 6 58 mg/L

Mode = 7.0 mg/L (number that appears most offten)

Median = 6.9 mg/L (central value)

Range = 7.0 mg/L (highest term) – 6.4 mg/L ((lowest term) = 0.6 mg/L

Lb of Pollutant = (Concentration in mg/L orppm) × (Flow in MGD) × (8.34) L1681_book.fm Page 140 Tuesday, October 5, 2004 10:51 AM

Trang 3

STATISTICS REVIEW 141

Example 6.2

Problem:

Flow at the time of sample collection is 0.500 MGD and BOD is10 mg/L Determine pounds

of BOD

Solution:

(6.2)

where

L = calculated loading for a sample day

N = number of samples

Example 6.3

Problem:

Given:

First sample day: ﬂow 0.50 MGD, BOD 10 mg/L

Second sample day: ﬂow 0.60 MGD, BOD 15 mg/L

Third sample day: ﬂow 0.40 MGD, BOD 5 mg/L

What is the loading average?

Solution:

(6.3)

(10) ×(0.50) × (8.34) = 41.7 lb of BOD

N

L1 = (0.5 MGD) (10 mg/L) (8.34) = 41.7 lb

L2 = (0.6 MGD) (15 mg/L) (8.34) = 75.06 lb

L3 = (0.4 MGD) (5 mg/L) (8.34) = 16.68 lb

L (41.7 lb) 75.06 lb + 16.68 lb

b

ave

Trang 4

where

C = concentration of sample

N = number of samples

Example 6.4

Problem:Determine the average mg/L

Given:

First sample day: BOD 10 mg/L

Second sample day: BOD 15 mg/L

Third sample day: BOD 5 mg/L

Solution:

Conducting and establishing trend analysis for use in process control and performance evaluation

is important in water and wastewater treatment plant operations Typically, in both industries, data extending over a long period are usually available To aid in this effort, the moving average computation is commonly used because it provides a method to develop trends for use in process control and performance evaluation

The moving average takes all the available data into account, provides a leveling of erratic data points, and limits the length of time an individual data point will have an impact upon the computation The moving average can be determined as an arithmetic or geometric mean and for varying periods (5, 7, or 28 days) The most common moving average is the 7-day arithmetic moving average Because the week is the period most commonly used in water/wastewater treat-ment, in this section we describe the procedure for calculation of the 7-day arithmetic moving average

collection period (5, 7, or 28 days) Each day’s moving average is calculated in the same way, using the most recent data period.

Procedure

Day 8 The result of this calculation is the moving average for Day 8.

change.

(6.4)

10 mg/L 15 mg/L 5 mg/L

Moving Average = Test 1 + Test 2 + Test 3 + Test 4 Test 6 Test 7

Number of Tests

Performed during the 7 Days = 10 mg/L L1681_book.fm Page 142 Tuesday, October 5, 2004 10:51 AM

Trang 5

Example 6.5

Problem:

The aeration tank solids concentration is determined daily The test results for the ﬁrst 10 days

of the month are shown in the following chart What is the 7-day moving average concentration

on Days 7, 8, 9, and 10?

Solution:

Geometric mean (or geometric average) is a statistical calculation used for reporting bacteriological test results in water/wastewater treatment plant operations Deﬁned, geometric mean is a calculated mean or average appropriate for data sets containing a few values that are very high relative to the other values To reduce the bias introduced to an arithmetic mean (average) by these very high numbers, the natural logarithms of the data are averaged The antilog of the average is the geometric

Day no Concentration (mg/L)

7-Day Moving Ave for Day 7 =2330 + 3360 + 22640 2755 2860 2650 2340

7

= 2705 mg/L

7

= 2708 mg/L

7

= 2640 mg/L

7-Day Moving Ave for Day 10 = 2755 + 2860 + 2650 2340 2350 2888 2330

7

= 2596 mg/L L1681_book.fm Page 143 Tuesday, October 5, 2004 10:51 AM

Trang 6

mean Simply stated, the geometric mean is not affected by wide shifts in test results to the same extent that the arithmetic mean is affected It can be computed using logarithms or by determining the Nth root of the product of the individual test results Although performing each of the calcu-lations is possible without a calculator, using one that can perform logarithm (log) functions and/or exponential (Y x) functions is best

6.4.5.1 Logarithm (Log) Method

To perform the calculations required to obtain a geometric mean using the log method, we must have a calculator capable of converting test results into their equivalent logarithms and converting the logarithm of the geometric mean back into its equivalent number (antilog):

(6.5)

Procedure

result with a one and determine the log of one.

geometric mean.

6.4.5.2 Nth Root Calculation Method

The calculated month geometric mean can also be calculated by multiplying the values of all the sample results obtained during the month (the number of samples, N) and taking the Nth root of the product:

The Nth root method requires a calculator that can multiply all the test results together and then determine the Nth root of the number

Procedure

• Multiply all of the reported test values (test 1 × test 2 × test 3 × … × test N).

in the previous step.

Example 6.6

Problem:

The results of the fecal coliform testing performed during the month of June are shown in the following table What is the geometric mean of the test results computed by the log method and the Nth root method?

Geometric Mean = Antilog log X1 + log X2 + llog X log X

N, Number of Tests

3 … + n









Geometric Mean = N X1 × X2 × … × Xn L1681_book.fm Page 144 Tuesday, October 5, 2004 10:51 AM

Trang 7

Solution:

Step 1 Geometric mean by the log method:

the product of all the test results during the period:

Using the calculator, determine the eighth root of this number (eighth because there are eight test results): eighth root = 51.

In addition to simple average, moving average, geometric mean, and range calculations, it may be desirable to test the precision of test results Standard deviation, s, is often used as an indicator of precision and is a measure of the variation (the spread in a set of observations) in the results Considering some of the basic theory of statistics is appropriate in order to gain better under-standing of and perspective on the beneﬁts derived from using statistical methods in environmental operations In any set of data, the true value (mean) lies in the middle of all the measurements taken This is true, providing the sample size is large and only random error is present in the analysis In addition, the measurements will show a normal distribution (see Figure 6.1)

Figure 6.1 shows that 68.26% of the results fall between M + s and M – s; 95.46% of the results lie between M + 2s and M – 2s; and 99.74% of the results lie between M + 3s and M – 3s Therefore,

if precise, 68.26% of all the measurements should fall between the true value estimated by the mean, plus the standard deviation and the true value minus the standard deviation The following equation is used to calculate the sample standard deviation:

Log

Geometric mean 13.62860

Log of Geometric Mean 13.62860

Antilog of 1.703575 = 50.5 or 51

20× 1 × 180 × 2133 × 69 × 96 × 19 ×44 L1681_book.fm Page 145 Tuesday, October 5, 2004 10:51 AM

Trang 8

where:

s = standard deviation

n = number of samples

X = measurements from X to X n

= the mean

∑ = means to sum the values from X to X n

Example 6.7

Problem:

Calculate the standard deviation, s, of the following dissolved oxygen values: 9.5; 10.5; 10.1; 9.9; 10.6; 9.5; 11.5; 9.5; 10.0; 9.4

Solution:

Figure 6.1 Normal distribution curve showing the frequency of a measurement.

X

3.99

+3s +2s +s M

− s

− 2s

− 3s

95.46%

68.26%

99.74%

−

n 1

X

X= 10 0

Trang 9

In this chapter, we have touched only on the basics of statistics Obviously, practicing environmental engineers need to know much more about this valuable tool For example, engineers must understand not only elementary probability and basic statistics — with emphasis on their application in engineering and the sciences — but also the treatment of data; sampling distributions; inferences concerning means; inferences concerning variances; inferences concerning proportions; nonpara-metric tests; curve ﬁtting; analysis of variance; factorial experimentation; and much more Because these topics are beyond the scope of this text, we highly recommend Richard A Johnson (1997)

Miller and Freund’s Probability and Statistics for Engineers, 6th ed., available from Prentice-Hall

s= 1 (3.99)

− (10 1)

s= 3.99 =0.67 9

Định dạng
Số trang	9
Dung lượng	469,73 KB