Control Windows Treatment of Priority TCP/IP Data Windows NT/2000/XP This parameter determines whether TCP uses the RFC 1122 specification for urgent data or the mode used by BSD- deriv
Trang 1Offload IP Security Task Processing (Windows 2000/XP)
This setting is used to control whether IP Security (IPSEC) tasks should be
offloaded to a network card with IP security capabilities
Enable IP Packet Forwarding (Windows NT/2000/XP)
By default, TCP/IP forwarding is not enabled in Windows, this setting can be used
to enable TCP/IP forwarding for all network connections that are installed and used by the computer
Control RFC 1323 Time Stamp and Window Scaling (Windows NT/2000/XP)
This setting controls RFC 1323 timestamps and window scaling options
Timestamps and Window scaling are enabled by default, but can be manipulated with flag bits
Control Selective Acknowledgement (SACK) Operation (Windows
NT/2000/XP)
This parameter controls whether or not Selective ACK (SACK - RFC 2018)
support is enabled With SACK enabled (default), a packet or series of packets can
be dropped, and the receiver informs the sender which data has been received, and where there may be "holes" in the data
Control Windows Treatment of Priority TCP/IP Data (Windows NT/2000/XP)
This parameter determines whether TCP uses the RFC 1122 specification for urgent data or the mode used by BSD- derived systems The two mechanisms interpret the urgent pointer in the TCP header and the length of the urgent data differently
Specify the Router Packet Queue Size (Windows NT/2000/XP)
This parameter determines the number of IP packet headers allocated for the router packet queue When all headers are in use, the router will begin to discard packets
at random from the queue
Control Keep Alive Parameters (Windows NT/2000/XP)
These settings control how Windows manages connection keep alive
transmissions Including the timeout before keepalives are sent and the interval between keepalive transmissions
Specify the Conformance Level for IP Multicast (Windows NT/2000/XP)
This parameter determines to what extent the system supports IP multicasting and participates in the Internet Group Management Protocol, RFC 1112
Trang 2Enable Dead Gateway Detection (Windows NT/2000/XP)
This setting specifies whether Windows should automatically detect and use an alternate gateway in the event of transmiting a segment several times without
receiving a response
Change the PPPOE MTU Size (Windows XP)
By default, a Windows XP PPPoE connection uses an MTU size that is 20 bytes less than the IP MTU of the LAN adapter over which the PPPoE packets are sent, which in most cases is 1480 bytes If a lower MTU is required, then this tweak can
be used to change the value
Control the Number of TCP/IP Connection Attempts (Windows 95/98/Me)
This setting controls the number of TCP/IP connection attempts (SYN packets) to
be transmitted before timing out
Modify the Number of Duplicate ACKs for Fast Retransmit (Windows
2000/XP)
This parameter determines the number of duplicate ACKs that must be received for the same sequence number of sent data before "fast retransmit" is triggered to
resend the segment that has been dropped in transit
Specify the Conformance Level for IP Multicast (Windows 95/98/Me)
This parameter determines to what extent the system supports IP multicasting and participates in the Internet Group Management Protocol, RFC 1112
Detect Black Hole Routers During Path MTU Discovery (Windows
NT/2000/XP)
Specifies whether the stack will attempt to detect Maximum Transmission Unit (MTU) routers that do not send back ICMP fragmentation-needed messages
Enable Path MTU Discovery (Windows NT/2000/XP)
Enabling the setting causes TCP to attempt to discover the Maximum Transmission Unit (MTU or largest packet size) over the path to a remote host By discovering the Path MTU and limiting TCP segments to this size, TCP can eliminate
fragmentation at routers along the path that connect networks with different MTUs
Disable TCP/IP Source Routing (Windows NT 4.0)
Normally, on a computer running Windows NT 4.0, you cannot disable the source routing feature for the TCP/IP protocol By using this tweak it is possible to disable
it
Trang 3Specify System-wide TCP Receive Window Size (Windows 2000/XP)
The TcpWindowSize parameter can be used to set the receive window on a per-interface basis This parameter can be used to set a global limit for the TCP
window size on a system-wide basis
Enable Dead Gateway Detection (Windows 95/98/Me)
This setting specifies whether Windows should automatically detect and use an alternate gateway in the event of a failed gateway
Specify the Maximum Number of TCP/IP Connections (Windows NT/2000)
This parameter specifies the maximum number of connections that TCP may have open simultaneously
Optimize Windows TCP/IP Data Retransmissions (Windows NT/2000/XP)
This parameter controls the number of times TCP will retransmit an individual data segment (not connection request segments) before aborting the connection
Control RFC 1323 Time Stamp and Window Scaling Options (Windows
95/98/Me)
This setting controls RFC 1323 time stamps and window scaling options for
TCP/IP packets
Specify the Default Time to Live for TCP/IP Packets (Windows NT/2000/XP)
Specifies the default Time To Live (TTL) value set in the header of outgoing IP packets The TTL determines the maximum amount of time an IP packet may live
in the network without reaching its destination It is effectively a limit on the
number of routers an IP packet may pass through before being discarded
Enable MTU Discovery (Windows 95/98/Me)
This setting specifies whether the TCP/IP stack will attempt to perform path MTU discovery as specified in RFC 1191
Enable MTU Black Hole Detection (Windows 95/98/Me)
Specifies whether the stack will attempt to detect Maximum Transmission Unit (MTU) routers that do not send back ICMP fragmentation-needed messages
Control Windows Treatment of Priority TCP/IP Data (Windows 95/98/Me)
This value specifies how Windows should handle urgent data transfers, either in a same manner to some UNIX systems or as specified by RFC 1122
Trang 4Specify the TCP/IP Receive Window Size (Windows 95/98/Me) Popular
This setting controls the size of the TCP/IP receive Window In general, larger receive windows work better with high-delay, high-bandwidth data
Optimize Windows TCP/IP Connection Retransmissions (Windows
NT/2000/XP)
This parameter determines the number of times TCP will retransmit a connect request (SYN) before aborting the attempt The retransmission timeout is doubled with each successive retransmission in a given connect attempt
Specify the Default TCP/IP Time to Live (Windows 95/98/Me)
This setting specifies the default time to live (TTL) value for IP packets generated
by the Windows TCP/IP stack
Optimize the Windows TCP/IP Window Size (Windows NT/2000) Popular
This parameter determines the maximum TCP receive window size offered by the system The receive window specifies the number of bytes a sender may transmit without receiving an acknowledgment
Change the Maximum Transmission Unit (MTU) Size (Windows NT/2000/XP)
Popular
This parameter specifies the Maximum Transmission Unit (MTU) for a network interface By optimizing the MTU setting you can gain substantial network
performance increases, especially when using dial-up modem connections
Enable Source Routing on Token Ring Networks (Windows NT/2000)
Setting this parameter to 1 will force TCP/IP to transmit ARP queries with source routing enabled on Token Ring networks By default, the stack transmits ARP queries without source routing first and retries with source routing enabled if no reply was received
Specify System-wide TCP Receive Window Size (Windows 98)
The TcpWindowSize parameter can be used to set the receive window on a per-interface basis This parameter can be used to set a global limit for the TCP
window size on a system-wide basis
Modify the Initial Retransmission Timeout (Windows NT/2000)
This parameter controls the initial retransmission timeout used by TCP on each new connection It applies to the connection request (SYN) and to the first data segment(s) sent on each connection
Trang 5Change TCP/IP Broadcast Address (Windows NT/2000)
This setting allows Windows to be configured to use zeros-broadcasts (0.0.0.0) instead of ones-broadcasts (255.255.255.255) Most systems use ones-broadcasts, but some systems derived from BSD implementations use zeros-broadcasts
Transmit Ethernet Packets Using 802.3 SNAP Encoding (Windows NT/2000)
Enabling this setting forces TCP/IP to transmit Ethernet packets using 802.3 SNAP encoding By default, the stack transmits packets in DIX Ethernet format It will always receive both formats
Specify the Default TCP/IP Type of Service (TOS) (Windows NT)
This setting specifies the default type of service (TOS) for IP packets generated by the TCP/IP stack This can be used to manage quality of service (QOS) throughout
a network
Configure the TCP/IP Settings of a Network Adapter (Windows NT/2000/XP)
Popular
These values control the TCP/IP parameters of the network interface cards
Configurable parameters include IP Address, Subnet Mask and Default Gateway
Specify the Default TCP/IP Type of Service (TOS) (Windows 95/98/Me)
This setting specifies the default type of service (TOS) for IP packets generated by the TCP/IP stack This can be used to manage quality of service (QOS) throughout
a network
Control the Number of TCP/IP Transmission Retries (Windows 95/98/Me)
This setting defines the number of transmission retries will be transmitted before the connection is aborted
Control TCP/IP Routing Parameters (Windows 95/98/Me)
These settings control IP routing features including the total amount of buffer space to allocate for routing packets and the maximum number of packets that can
be routed simultaneously
Override the Default Broadcast Address (Windows 95/98/Me)
This setting overrides the default broadcast address that is derived from the IP address and subnet mask Primarily the broadcast address is used for NetBIOS name queries