On the Guest Operating System page, shown in Figure 23-5, first select the appropriate type of guest operating system that will run in the virtual machine.. On the Memory and Processors
Trang 1372 Networking: A Beginner’s Guide
Virtual machines are created using a wizard-like process that walks you through making all the appropriate choices Here are the steps:
1 Click the Create Virtual Machine link in the VMware Server console’s Command pane You see the Create Virtual Machine screen, as shown in Figure 23-4
2 On the Name and Location page, name the virtual machine you will create
In this example, I’ve named it Ubuntu 9.0.3 You should also verify that the correct datastore has been selected (if you have more than one) Click Next to continue
Figure 23-3. Creating a new VMware datastore
Trang 2373 Chapter 23: Introduction to Virtualization
3 On the Guest Operating System page, shown in Figure 23-5, first select the
appropriate type of guest operating system that will run in the virtual machine
In the Version drop-down list, you will see that a wide variety of supported
guest Linux versions are available, including some choices for generic Linux
distributions Select the version that is closest to that of your guest operating
system Then click Next to continue
4 On the Memory and Processors page, shown in Figure 23-6, based on the guest
operating system you chose in the preceding step, VMware will propose a
sug-gested value for the amount of RAM to give it You can accept this amount or
change it Note that you can increase this amount later if necessary
Figure 23-4. Starting to create a virtual machine
Trang 3374 Networking: A Beginner’s Guide
NOTE The amount of RAM you allocate to the virtual machine will come from the host computer’s available RAM and, while the virtual machine is running, will not be available for the host operating system Therefore, you do not want to allocate all of the computer’s installed RAM to the virtual machine, as then the host operating system would not have enough RAM to do its work, and it would likely thrash its virtual memory file and become unusable On the other hand, you don’t want to allocate too little RAM to the virtual machine, particularly if you know you’ll be performing memory-intensive actions within the virtual machine, as then the virtual machine wouldl run poorly
As a general rule, unless you’re limited in the amount of installed RAM on the computer, or if you’re planning on running many parallel virtual machines at the same time, I recommend increasing the amount of RAM allocated by 50 to 100 percent of the default suggested by VMware
Figure 23-5. Choosing the guest operating system
Trang 4375 Chapter 23: Introduction to Virtualization
5 If you’re using a multicore or multiprocessor computer, you can select how
many processors the virtual machine can monopolize while it’s running
Unlike the amount of RAM, which can be easily changed later, the choice you
make for the number of processors to allocate should not be changed without
re-creating the virtual machine from scratch This is because when you install
a guest operating system, the guest operating system installation will often
be installed to support the number of processors it originally detects If you
increase or decrease the number of processors allocated to the virtual machine,
the guest operating system may no longer start or operate properly After
mak-ing your RAM and processor choices, click Next
Figure 23-6. Setting the amount of RAM for the guest operating system
Trang 5376 Networking: A Beginner’s Guide
6 From the Hard Disk page, shown in Figure 23-7, you can choose to create a new virtual disk or use an existing one The hard disk for a virtual machine is actually a file stored on the real hard disk of the host operating system All of the guest operating system’s files will be stored in that virtual hard disk file From the perspective of the virtual machine, it has a hard disk installed with
a size that you specify From the perspective of the host operating system, it’s just a single file stored in the VMware datastore location For almost all virtual machines, you will need to create a virtual hard disk, and this example is no exception Click Create a New Disk
7 On the Properties page for the hard disk, shown in Figure 23-8, you can set a number of properties for creating a virtual hard disk Choose from the follow-ing choices, and then click Next
N Size of the virtual hard disk VMware will, based on the operating system you’ve selected, propose a size for the virtual hard disk While it
is possible to increase this later, it can be difficult to do so Accordingly, I recommend that you set the size to be larger than you think you need
Figure 23-7. Choosing your virtual disk