CCNA 1 and 2 Companion Guide, Revised (Cisco Networking Academy Program) part 58 docx

This term is usually used in conjunction with specific routing protocols, such as Open Shortest Path First OSPF or Border Gateway Protocol BGP, that enable a network to be carved into num

More Information: Roles of the Router in WANs (Continued)

■ Autonomous system—An autonomous system (AS) is a network or internetwork (either

LAN or WAN) that is relatively self-contained It is administered by a single person (or organization), features a single routed protocol, has an address architecture, and usually involves just one routing protocol An autonomous system can support connections to other autonomous systems owned and operated by the same organization Alternatively,

an AS might have connections to other networks, such as the Internet, yet it retains auton-omy of operation This term is usually used in conjunction with specific routing protocols, such as Open Shortest Path First (OSPF) or Border Gateway Protocol (BGP), that enable a network to be carved into numbered subsections

Given these definitions, it is possible to better define the functional classes of routers An

inte-rior router is one that can be used by end systems in a network to access other end systems

within the same network The interior router supports no connections to any other network

Figure 10-11 illustrates a small network and identifies those devices that function as interior

routers

Figure 10-11 Interior Routers in a Network

An exterior router is one that lies beyond the boundaries of any given network Figure 10-12,

although not pretending to depict the Internet’s actual topology, presents a highly simplified

Internet topology that is solely intended to demonstrate what an exterior router is

continues

Router Router

Router

Interior Routers Internetwork

More Information: Roles of the Router in WANs (Continued)

Figure 10-12 Exterior Routers

The last functional class of router is the border router As the name implies, border routers interconnect a network with other networks It is important to note that a single entity might own and operate multiple autonomous systems Therefore, a border router may denote the boundary between two autonomous systems rather than the border between a private network and some other network Figure 10-13 identifies the border routers in the sample network that was used in Figure 10-11 and Figure 10-12

Figure 10-13 Border Routers

Router Router

Router

Exterior Routers Internetwork

Router Router

Router

Internetwork

Border Routers

Lab WAN Simulation

A viable WAN connection can connect routers from around the world In an academy

lab, all the networks are connected with a serial or Ethernet cable, and the students

can see and physically touch the equipment In a real-world situation, one router could

be in New York, while another router could be in Sydney, Australia An administrator

located in Sydney would have to connect to the router in New York through the WAN

cloud to troubleshoot the New York router.

In the academy lab, the whole dedicated circuit cloud has been made extremely small

and put in the “crack” between the back-to-back DTE-DCE cables The connection

from one router’s interface s0/0 to another's router interface s0/1 simulates the entire

circuit cloud.

Note that clocking must be configured, or this will not work properly for the use of

CSU/DSU.

More Information: Internetworking Scenarios

Having examined the concepts underlying routing and internetworking, as well as some of the

terminology inherent with these topics, you can see how they are used by examining three

internetworking scenarios Each scenario demonstrates some of the issues that need to be

addressed in any network or internetwork:

■ Routing within a network

■ Routing between adjacent networks

■ Routing between nonadjacent networks

These three generic aspects encompass virtually every form of internetworking that you are

likely to encounter Each one holds different implications for the network administrator,

includ-ing such routinclud-ing aspects as route calculation and distribution, convergence, and security The

following sections provide an overview of each internetworking scenario and highlight the

areas of concern for a network administrator The various potential resolutions to these routing

concerns are presented throughout this book

Routing Within a Network

The simplest form of routing is routing within the confines of a single network Such a network

contains just interior routers In theory, this form of network uses just one routed protocol, one

address architecture, and a minimum number of destinations This structure greatly reduces

the workload of each router and maximizes potential network performance Therefore, the

routing issues in intranetwork routing are more closely related to the network’s size and

topol-ogy than to its address architectures and routing protocols The topoltopol-ogy must be carefully

selected to match the requirements of the user community

continues

More Information: Internetworking Scenarios (Continued)

If the network is small enough, it might be feasible for the administrator to preprogram all the possible routes statically rather than introduce the complexity of a dynamic routing protocol Statically programmed routes, however, can become an onerous burden in a growing or con-stantly changing network You have to go to each router and manually update each time a change occurs in the network rather than having routers automatically update

Routing Between Adjacent Networks

A small step up in complexity from intranetwork routing is internetwork routing between adja-cent networks Physical adjacency means that the two networks are directly connected to each other Such an adjacency might have been designed to promote rapid convergence, improve security, or satisfy any number of other performance criteria

The logical separation of the multiple networks implies that the border routers must summa-rize and redistribute routing information between them In this fashion, the end systems of one network can directly address the end systems in another network Figure 10-14 illustrates this type of routing

Figure 10-14 Routing Between Adjacent Networks

The routing issues you need to address in this type of internetwork arise from the differences between the two networks Some of the potential differences that must be identified include the following:

■ Do the networks belong to the same organization? If not, the border routers need to secure the network’s perimeter

■ Do the networks use the same routing protocol? If not, you need to find some mutually acceptable metric

■ Do the networks use the same routed protocol? If not, you might have to support a second routed protocol in your network to facilitate internetworking

Internet

Router

Router

Router Router Router

More Information: Internetworking Scenarios (Continued)

Additionally, topology can affect routing between adjacent networks Using a single point of

interconnection between the two networks, for example, makes it easy to control the calculation

and redistribution of routing information between the networks This convenience introduces

a single point of failure, however, and it might not be acceptable to your users Introducing a

second (or more) interconnection point solves the single point of failure problem but can

create the opportunity for infinite routing loops to occur Resolving such a dilemma requires an

understanding of your users’ tolerance for downtime and risk Armed with this understanding,

you can evaluate specific routing protocols for their capabilities to converge quickly and

com-pensate for potential routing problems

Routing Between Nonadjacent Networks

Routing between nonadjacent networks is simultaneously the most complicated and useful

type of routing Two networks can use a third network as an intermediary It is highly likely that

the three different networks will use different routing protocols, routed protocols, and address

architectures Therefore, the boundary router’s job is to overcome these obstacles to

commu-nication while also guarding the border of its network Figure 10-15 illustrates routing between

nonadjacent small networks

Figure 10-15 Routing Between Nonadjacent Networks

The border router of each private network in this illustration needs to protect the border of its

network from unwanted intrusion Because the two networks that need to communicate aren’t

adjacent and the intermediary network is beyond their control, the risks of unwanted intrusion

are much higher than if the networks were directly internetworked Therefore, the network

administrators must develop a set of criteria for allowing specific external users into their

net-work, while disallowing access to everyone else The border router implements these criteria

in an access control list

continues

Internet

Router

Router

Router Router Router

In this chapter, you learned the following the key points:

■ The Internet is the interconnection of thousands of large and small networks all over the world.

■ A WAN is used to interconnect LANs that are separated by a large geographic distance.

■ Dedicated line, circuit-switching, packet-switching, and cell-switching are some

of the common WAN connection types.

■ Many types of WAN services are available to the WAN subscriber, who must know how to interface to the WAN provider’s service.

■ WAN devices include routers, WAN switches, modems, CSUs/DSUs, and access servers.

■ WAN physical layer protocols describe how to provide electrical, mechanical, operational, and functional connection for WAN services.

■ WAN data link layer protocols describe how frames are carried between systems

on a single data link.

To supplement all that you’ve learned in this chapter, refer to the chapter-specific Videos, PhotoZooms, and e-Lab activities on the CD-ROM accompanying this book.

More Information: Internetworking Scenarios (Continued) Another responsibility of the border router is to summarize the internal routes and redistribute this information to the networks beyond This process enables users outside the bounds of the private network to access its end systems If this routing information isn’t distributed, no one outside that private network is able to access its end systems

Finally, it is highly likely that the border routers will have to be configured to use multiple routing protocols An interior gateway protocol will likely be selected for intranetwork routing purposes Calculating routes across the internetwork, however, might require a different proto-col—one that features stronger support for route summarization Route summarization can reduce routing table size by aggregating routes to multiple networks into one or two routing entries

Key Terms

cell-switched services Provide a dedicated-connection switching technology that

organizes digital data into cell units and transmits them over a physical medium using

digital signal technology.

circuit switching A WAN switching method in which a dedicated physical circuit

through a carrier network is established, maintained, and terminated for each

commu-nication session ISDN is an example of a circuit-switched WAN technology.

DCE (data circuit-terminating equipment) (ITU-T expansion) Devices and connections

of a communications network that comprise the network end of the user-to-network

interface The DCE provides a physical connection to the network, forwards traffic,

and provides a clocking signal used to synchronize data transmission between DCE

and DTE devices Modems and interface cards are examples of DCE.

DTE (data terminal equipment) Device at the user end of a user-network interface

that serves as a data source, destination, or both DTE connects to a data network

through a DCE device (for example, a modem) and typically uses clocking signals

generated by the DCE DTE includes such devices as computers, protocol translators,

and multiplexers.

modem Device that converts digital and analog signals At the source, a modem

converts digital signals to a form suitable for transmission over analog communication

facilities At the destination, the analog signals are returned to their digital form

Modems allow data to be transmitted over voice-grade telephone lines The term

modem is also used to describe various digital devices such as CSU/DSUs and ISDN

terminal adapters.

packet-switched services Routes small units of data called packets through a

network based on the destination address contained within each packet.

propagation delay Time required for data to travel over a network from its source

to its ultimate destination.

router Network layer device that uses one or more metrics to determine the optimal

path along which network traffic should be forwarded Routers forward packets from

one network to another based on network layer information.

switch Network device that filters, forwards, and floods frames based on the

destina-tion address of each frame The switch operates at the data link layer of the OSI

model.

uptime The amount of time that the device is functional and in service relative to the

users’ requirements for its availability.

WAN (wide-area network) A data communications network spanning a large geo-graphic area, such as a state, province or country WANs often use transmission facili-ties provided by common carriers, for example, telephone companies.

Check Your Understanding

Complete all the review questions to test your understanding of the topics and con-cepts in this chapter Answers are listed in Appendix C, “Check Your Understanding Answer Key.”

1. Which of the following best describes a WAN?

A. Connects LANs that are separated by a large geographic area

B. Connects workstations, terminals, and other devices in a metropolitan area

C. Connects LANs within a large building

D. Connects workstations, terminals, and other devices within a building

A. WANs emphasize access over serial interfaces operating at lower speeds.

B. WANs provide high-speed multiple access services.

C. WANs typically exist in small geographic areas.

D. WANs use tokens to regulate network traffic.

3. Which of the following are examples of WAN technologies?

C. Star, Banyan VINES

4. Which layers of the OSI model do WAN standards describe?

A. Data link and network

B. Data link and presentation

C. Physical and application

D. Physical and data link

5. Which best describes data circuit-terminating equipment (DCE)?

A. Consists of the user device at the end of a network

B. Serves as the data source or destination

C. Consists of physical devices such as protocol translators and multiplexers

D. Consists of physical devices at the end of a WAN connection

6. Which of the following components provides interface voice-grade services,

channel service units/digital service units (CSUs/DSUs) that interface T1/E1 services, and terminal adapters/Network Termination 1 (TAs/NT1s) that interface Integrated Services Digital Network (ISDN) services?

A. Switches

B. Routers

7. Which of the following concentrates the dial-in and dial-out user connections?

A. Switches

B. Routers

8. Some WAN physical and data link layer standards are:

B. PPP

D. All of the above

9. Match the functions with the components.

3) ROM

5) Interface

a RAM that retains its contents when a unit is powered off

b Volatile memory that can be read and written by the microprocessor

c Volatile memory that can be read but not written by a microprocessor

d Nonvolatile storage that can be electrically erased and reprogrammed so that software images can be stored, booted, and rewritten as necessary

e Connection between two systems or devices Select your answer:

A. 1-b, 2-a, 3-c, 4-e, 5-d

B. 1-a, 2-b, 3-c, 4-e, 5-d

C. 1-b, 2-a, 3-e, 4-c, 5-d

D. 1-b, 2-a, 3-c, 4-d, 5-e

10. Any internetwork will probably include the following:

A. Consistent end-to-end addressing and priority-level bandwidth allocation capabilities

B. Addresses that represent network topologies and assurance of quality of service

C. Best path selection and dynamic routing

D. All of the above

11. Which of the following are data link encapsulations for WAN?

A. High-Level Data Link Control (HDLC)

C. Point-to-Point Protocol (PPP)

D. All of the above

12. What are the main functions of routers?

A. The determination of best paths for incoming data packets and the switching

of packets to the proper outgoing interface

B. Replying to ARP requests when two nodes are on different LANs

C. Building routing tables and exchanging the network information contained within them with other routers

D. Both A and B