Practical TCP/IP and Ethernet Networking- P6 pdf

As a physical topology, a bus describes a network in which each node is connected to a common single communication channel or ‘bus’.. This is because nodes can spend much of their time t

• 802.1E System load protocol

• 802.1F Guidelines for layer management standards

• 802.1G Remote MAC bridges

• 802.1I MAC bridges (FDDI supplement) /+++2UMOIGRROTQIUTZXUR

This is the interface between the network layer and the specific network environments at the physical layer The IEEE has divided the data link layer in the OSI model into two sub layers – the media access MAC sub layer, and the logical link layer LLC The logical link control protocol is common for all IEEE 802 standard network types This provides a common interface to the network layer of the protocol stack The protocol used at this sub layer is based on IBM’s SDLC protocol, and can be used in three modes, or types

These are:

• Type 1: Unacknowledged connectionless link service

• Type 2: Connection oriented link service

• Type 3: Acknowledged connectionless link service, used in real time applications such as manufacturing control

/+++)93')*

The carrier sense, multiple accesses with collision detection type LAN is commonly – but strictly speaking incorrectly – known as an Ethernet LAN Ethernet refers to the original DEC/INTEL/XEROX product known as Version II (or Bluebook) Ethernet

Subsequent to ratification this system has been known as IEEE 802.3 IEEE 802.3 is virtually identical, but not absolutely identical to Bluebook Ethernet, in that they differ in two bytes within the frame The following chapter will deal with this anomaly

Subsequently, two additional specifications have been approved viz IEEE 802.3u (100 Mbps or ‘fast’ Ethernet) and IEEE 8023z (1000 Mbps or ‘gigabit’ Ethernet)

/+++:UQKTH[Y

The other major access method for a shared medium is the use of a token This is a type

of data frame that a station must possess before it can transmit messages The stations are connected to a passive bus, although the token logically passes around in a cyclic manner

This standard is the ratification of the Token Bus LAN developed by General Motors for its manufacturing automation protocol (MAP) The media used is usually broadband coax, and speeds vary from 1 Mbps to 10 Mbps

/+++:UQKTXOTM

As in 802.4, data transmission can only occur when a station holds a token The logical structure of the network wiring is in the form of a ring, and each message must cycle through each station connected to the ring

This standard is the ratified version of the IBM token ring LAN However, where IBM token ring supports speed of 4 and 16 Mbps, IEEE 802.5 supports 1 and 4 Mbps The physical media for the token ring can be unshielded twisted pair, coaxial cable or optical fiber

The original specification called for a single ring, which creates a problem if the ring gets broken A subsequent enhancement of the specification, called IEEE 802.5u, introduces the concept of a dual redundant ring, which enables the system to continue operating in case of a cable break

Work is currently underway on a 100 Mbps token ring specification

/+++3KZXUVUROZGTGXKGTKZ]UXQY

This committee is responsible for defining the standards for MANs It has recommended that a system known as distributed queue data bus (DQDB) be utilized as a MAN standard

The DQDB network is sponsored by Telecom Australia and defines the protocol for integrated voice and data on the same medium, within an area up to 15 km in diameter

/+++(XUGJHGTJ2'4YZKINTOIGRGJ\OYUX_MXU[V:'-

The 802.7 Committee provides technical advice on broadband technique

/+++,OHKXUVZOI2'4Y:'-

The fiber optic equivalent of the 802.7 broadband TAG The committee is attempting to standardize physical compatibility with FDDI and synchronous optical networks (SONET) It is also investigating single mode fiber and multimode fiber architectures

/+++/TZKMXGZKJ\UOIKGTJJGZG2'4Y

This committee has recently released a specification for isochronous Ethernet as IEEE 802.9a It provides a 6.144 Mbps voice service (96 channels at 64 kbps) multiplexed with

10 Mbps data on a single cable It is designed for multimedia applications

/+++9KI[XK2'4Y

Current proposals include two methods to address the lack of security in the original specifications These are:

• A secure data exchange sub layer SDE sitting between the LLC and the MAC sub layer There will be different SDEs for different systems i.e military and medical

• A secure interoperable LAN system architecture SILS This will define system standards for secure LAN communications

/+++=OXKRKYY2'4Y

The IEEE802.11 Wireless LAN standard uses the 2.4 GHz band and allows operation to 1

or 2 Mbps The 802.11b standard also uses the 2.4 GHz band, but allows operation at

11 Mbps The latest IEEE 802.11a specification use the 5.7 GHz band instead and allows operation at 54 Mbps

/+++,GYZ2'4Y

This specification covers the system known as 100VG AnyLAN Developed by Hewlett-Packard, this system operates on voice grade (CAT3) cable – hence the VG in the name The AnyLAN indicates that the system can interface with both IEEE 802.3 and IEEE 802.5 networks (by means of a special speed adaptation bridge)

 (XUGJIGYZGTJVUOTZZUVUOTZZUVURUMOKY

The way the nodes are connected to form a network is known as its topology There are many topologies available but they form two basic types, broadcast and point-to-point

Broadcast topologies are those where the message ripples out from the transmitter to reach all nodes There is no active regeneration of the signal by the nodes and so signal propagation is independent of the operation of the network electronics This then limits the size of such networks

Figure 2.13 shows an example of a broadcast topology

Figure 2.13

Broadcast topology

In a point-to-point communications network, however, each node is communicating directly with only one node That node may actively regenerate the signal and pass it on

to its nearest neighbor Such networks have the capability of being made much larger Figure 2.14 shows some examples of point-to-point topologies

Figure 2.14

Point-to-point topologies

 2UMOIGRGTJVN_YOIGRZUVURUMOKY

A logical topology defines how the elements in the network communicate with each other, and how information is transmitted through a network The different types of media-access methods, determine how a node gets to transmit information along the network In a bus topology, information is broadcast, and every node gets the same information within the amount of time it actually takes a signal to cover the entire length

of cable This time interval limits the maximum speed and size for the network In a ring topology, each node hears from exactly one node and talks to exactly one other node Information is passed sequentially, in an order determined by a predefined process A polling or token mechanism is used to determine who has transmission rights, and a node can transmit only when it has this right

A physical topology defines the wiring layout for a network This specifies how the elements in the network are connected to each other electrically This arrangement will determine what happens if a node on the network fails Physical topologies fall into three main categories bus, star, and ring topology Combinations of these can be used to form

hybrid topologies to overcome weaknesses or restrictions in one or other of these three component topologies

A bus refers to both a physical and a logical topology As a physical topology, a bus describes a network in which each node is connected to a common single communication channel or ‘bus’ This bus is sometimes called a backbone, as it provides the spine for the network Every node can hear each message packet as it goes past

Logically, a passive bus is distinguished by the fact that packets are broadcast and every node gets the message at the same time Transmitted packets travel in both directions along the bus, and need not go through the individual nodes, as in a point-to-point system Rather, each node checks the destination address that is included in the message packet to determine whether that packet is intended for the specific node When the signal reaches the end of the bus, an electrical terminator absorbs the packet energy to keep it from reflecting back again along the bus cable, possibly interfering with other messages already on the bus Each end of a bus cable must be terminated, so that signals are removed from the bus when they reach the end

In a bus topology, nodes should be far enough apart so that they do not interfere with each other However, if the backbone bus cable is too long, it may be necessary to boost the signal strength using some form of amplification, or repeater The maximum length of the bus is limited by the size of the time interval that constitutes ‘simultaneous’ packet reception Figure 2.15 illustrates the bus topology

Figure 2.15

Bus topology

([YZUVURUM_GJ\GTZGMKY

Bus topologies offer the following advantages:

• A bus uses relatively little cable compared to other topologies, and arguably has the simplest wiring arrangement

• Since nodes are connected by high impedance tappings across a backbone cable, it’s easy to add or remove nodes from a bus This makes it easy to extend a bus topology

• Architectures based on this topology are simple and flexible

• The broadcasting of messages is advantageous for one-to-many data transmissions

([YZUVURUM_JOYGJ\GTZGMKY

These include the following:

• There can be a security problem, since every node may see every message, even those that are not destined for it

• Diagnosis/troubleshooting (fault-isolation) can be difficult, since the fault can be anywhere along the bus

• There is no automatic acknowledgment of messages, since messages get absorbed at the end of the bus and do not return to the sender

• The bus cable can be a bottleneck when network traffic gets heavy This is because nodes can spend much of their time trying to access the network

A star topology is a physical topology in which multiple nodes are connected to a central component, generally known as a hub The hub of a star usually is just a wiring center; that is, a common termination point for the nodes, with a single connection continuing from the hub In some cases, the hub may actually be a file server (a central computer that contains a centralized file and control system), with all its nodes attached directly to the server As a wiring center, a hub may, in turn, be connected to the file server or to another hub

All signals, instructions, and data going to and from each node must pass through the hub to which the node is connected The telephone system is doubtless the best known example of a star topology, with lines to individual customers coming from a central telephone exchange location There are not many LAN implementations that use a logical star topology The low impedance ARCnet networks are probably the best examples However, you will see that the physical layout of many other LANs look like a star topology even though they are considered to be something else An example of a star topology is shown in Figure 2.16

Figure 2.16

Star topology

9ZGXZUVURUM_GJ\GTZGMKY

• Troubleshooting and fault isolation is easy

• It is easy to add or remove nodes, and to modify the cable layout

• Failure of a single node does not isolate any other node

• The inclusion of a central hub allows easier monitoring of traffic for management purposes

9ZGXZUVURUM_JOYGJ\GTZGMKY

• If the hub fails, the entire network fails Sometimes a backup central machine is included, to make it possible to deal with such a failure

• A star topology requires a lot of cable

A ring topology is both a logical and a physical topology As a logical topology, a ring is distinguished by the fact that message packets are transmitted sequentially from node to

node, in a predefined order, and as such it is an example of a point-to-point system Nodes are arranged in a closed loop, so that the initiating node is the last one to receive a packet As a physical topology, a ring describes a network in which each node is connected to exactly two other nodes

Information traverses a one-way path, so that a node receives packets from exactly one node and transmits them to exactly one other node A message packet travels around the ring until it returns to the node that originally sent it In a ring topology, each node can act

as a repeater, boosting the signal before sending it on Each node checks whether the message packet’s destination node matches its address When the packet reaches its destination, the destination node accepts the message, then sends it back to the sender, to acknowledge receipt

As you will see later in this chapter, since ring topologies use token passing to control access to the network, the token is returned to sender with the acknowledgment The sender then releases the token to the next node on the network If this node has nothing to say, the node passes the token on to the next node, and so on When the token reaches a node with a packet to send, that node sends its packet Physical ring networks are rare, because this topology has considerable disadvantages compared to a more practical star-wired ring hybrid, which is described later

Figure 2.17

Ring topology

8OTMZUVURUM_GJ\GTZGMKY

• A physical ring topology has minimal cable requirements

• No wiring center or closet is needed

• The message can be automatically acknowledged

• Each node can regenerate the signal 8OTMZUVURUM_JOYGJ\GTZGMKY

• If any node goes down, the entire ring goes down

• Diagnosis/troubleshooting (fault isolation) is difficult because communication is only one-way

• Adding or removing nodes disrupts the network

• There will be a limit on the distance between nodes

As well as these three main topologies, some of the more important variations will now

be considered Once again, you should be clear that these are just variations, and should not be considered as topologies in their own right



 9ZGX]OXKJXOTMZUVURUM_

A star-wired ring topology, also known as a hub topology, is a hybrid physical topology that combines features of the star and ring topologies Individual nodes are connected to a central hub, as in a star network Within the hub, however, the connections are arranged into an internal ring Thus, the hub constitutes the ring, which must remain intact for the network to function The hubs, known as multistation access units (MAUs) in IBM token ring network terminology, may be connected to other hubs In this arrangement, each internal ring is opened and connected to the attached hubs, to create a larger, multi-hub ring

The advantage of using star wiring instead of simple ring wiring is that it is easy to disconnect a faulty node from the internal ring The IBM data connector is specially designed to close a circuit if an attached node is disconnected physically or electrically

By closing the circuit, the ring remains intact, but with one less node The IBM token ring networks are the best-known example of a star-wired ring topology In token ring networks, a secondary ring path can be established and used if part of the primary path goes down The star-wired ring is illustrated in Figure 2.18

Figure 2.18

Star-wired ring

The advantages of a star-wired ring topology include:

• Troubleshooting, or fault isolation, is relatively easy

• The modular design makes it easy to expand the network, and makes layouts extremely flexible

• Individual hubs can be connected to form larger rings

• Wiring to the hub is flexible

The disadvantages of a star-wired ring topology include:

• Configuration and cabling may be complicated because of the extreme flexibility of the arrangement

 *OYZXOH[ZKJYZGXZUVURUM_

A distributed star topology is a physical topology that consists of two or more hubs, each

of which is the center of a star arrangement A good example of such a topology is an

ARCnet network with at least one active hub and one or more active or passive hubs The 100VG ANYLAN utilizes a similar topology

Figure 2.19

Distributed star topology

 3KYNZUVURUM_

A mesh topology is a physical topology in which there are at least two paths to and from every node This type of topology is advantageous in hostile environments in which connections are easily broken If a connection is broken, at least one substitute path is always available A more restrictive definition requires each node to be connected directly to every other node Because of the severe connection requirements, such restrictive mesh topologies are feasible only for small networks

Figure 2.20

Mesh network

 :XKKZUVURUM_

A tree topology, also known as a distributed bus or a branching tree topology, is a hybrid physical topology that combines features of star and bus topologies Several buses may be daisy-chained together, and there may be branching at the connections (which will be hubs) The starting end of the tree is known as the root or head end This type of topology

is used in delivering cable television services

The advantages of a tree topology are:

• The network is easy to extend by just adding another branch, and that fault isolation is relatively easy

The disadvantages include:

• If the root goes down, the entire network goes down

• If any hub goes down, all branches off that hub go down

• Access becomes a problem if the entire network becomes too big

Figure 2.21

Tree topology

A common and important method of differentiating between different LAN types is to consider their media access methods Since there must be some method of determining which node can send a message, this is a critical area that determines the efficiency of the LAN There are a number of methods, which can be considered, of which the two most

common in current LANs are the contention method and the token passing method

You will become familiar with these as part of your study of LANs, although some of the other methods will also be briefly discussed

 )UTZKTZOUTY_YZKSY

The basis for a first-come-first-served media accesses method This operates in a similar manner to polite human communication We listen before we speak, deferring to anyone who already is speaking If two of us start to speak at the same time, we recognize that fact and both stop, before starting our messages again a little later In a contention-based access method, the first node to seek access when the network is idle will be able to

transmit Contention is at the heart of the carrier sense multiple access/collision

detection (CSMA/CD) access method used in the IEEE 802.3 and Ethernet V2 networks

The carrier sense component involves a node wishing to transmit a message listening to the transmission media to ensure there is no ‘carrier’ present In fact, the signaling method used on Ethernet type systems that make use of this method do not use a carrier in its true sense, and the name relates back to the original Aloha project in Hawaii that used radio links for transmission The length of the channel and the finite propagation delay means that there is still a distinct probability that more than one transmitter will attempt

to transmit at the same time, as they both will have heard ‘no carrier’ The collision detection logic ensures that more than one message on the channel simultaneously will be detected and transmission, from both ends, eventually stopped The system is a probabilistic system, since access to the channel cannot be ascertained in advance

 :UQKTVGYYOTM

Token passing is a deterministic media access method in which a token is passed from node to node, according to a predefined sequence A token is a special packet, or frame, consisting of a signal sequence that cannot be mistaken for a message At any given time, the token can be available or in use When an available token reaches a node, that node can access the network for a maximum predetermined time, before passing the token on

This deterministic access method guarantees that every node will get access to the network within a given length of time, usually in the order of a few milliseconds This is

in contrast to a probabilistic access method (such as CSMA/CD), in which nodes check for network activity when they want to access the network, and the first node to claim the idle network gets access to it Because each node gets its turn within a fixed period, deterministic access methods are more efficient on networks that have heavy traffic With such networks, nodes using probabilistic access methods spend much of their time competing to gain access and relatively little time actually transmitting data over the network Network architectures that support the token passing access method include token bus, ARCnet, FDDI, and token ring

To transmit, the node first marks the token as ‘in use’, and then transmits a data packet, with the token attached In a ring topology network, the packet is passed from node to node, until the packet reaches its destination The recipient acknowledges the packet by sending the message back to the sender, who then sends the token on to the next node in the network

In a bus topology network, the next recipient of a token is not necessarily the node that

is nearest to the current token passing node Rather, the next node is determined by some predefined rule The actual message is broadcast on to the bus for all nodes to ‘hear’ For example, in an ARCnet or token bus network, the token is passed from a node to the node with the next lower network address Networks that use token passing generally have some provision for setting the priority with which a node gets the token Higher-level protocols can specify that a message is important and should receive higher priority

Figure 2.22

Token passing

A token ring network requires an active monitor (AM) and one or more standby monitors (SMs) The AM keeps track of the token to make sure it has not been corrupted, lost, or sent to a node that has been disconnected from the network If any of these things happens, the AM generates a new token, and the network is back in business The SM makes sure the AM is doing its job and does not break down and get disconnected from the network If the AM is lost, one of the SMs becomes the new AM, and the network is again in business These monitoring capabilities make for complex circuitry on network interface cards that use this media access method

 6URROTM

Polling refers to a process of checking elements, such as computers or queues, in some defined order, to see whether the polled element needs attention (wants to transmit, contains jobs, and so on) In roll call polling, the polling sequence is based on a list of elements available to the controller In contrast, in hub polling, each element simply polls the next element in the sequence