Scalable voip mobility intedration and deployment- P16 pot

Note how the phase modulated signal is offset— in this example of simple of phase modulation, the modulated appears to be reflected vertically, the result of its phase having been altere

the other from the center frequency, and uses that drift to derive the original data For car radios, which are usually analog, that drift becomes the signal that is sent to the speakers

There is a third type, phase modulation (PM or ΦM, as Φ is the custom mathematical

symbol for phase, measured in degrees from 0 to 360), which works by altering the phase

how it compares to frequency modulation Note how the phase modulated signal is offset—

in this example of simple of phase modulation, the modulated appears to be reflected vertically, the result of its phase having been altered by 180 degrees—when the data signal

is non-zero, whereas the frequency modulated signal clearly has been sped up or slowed down for non-zero data

Because the phase of a signal is the offset from the carrier in degrees, and the amplitude is just a distance the peak of the carrier is offset from the origin, an amplitude and phase modulated signal can be represented using polar coordinates In the descriptions here I will try to avoid unnecessary mathematics, but the concept that the type of modulation applied

to a carrier can be represented by polar coordinates is powerful for those interested in

-1.0

-0.6

-0.2

0.2

0.6

1.0

0.0

0.2

0.4

0.6

0.8

1.0

-1.0

-0.6

-0.2

0.2

0.6

1.0

Carrier

Data Signal (between 0 and 1)

Final Modulated Signal = Data Signal × Carrier

Figure 5.14: Analog Amplitude Modulation

understanding just what radios do to the signal to be able to transmit the data The polar

coordinate representation is one of the two common methods for representing complex

numbers, and the designs of radios are always though of as involving complex math (A

complex number is type of number that can represents the square roots of negative numbers, something not allowed in real numbers.) For those interested in the details, the appendix at the end of this chapter explores the mathematics

The term “baseband” refers to the signal converted into a function that, when multiplied by the carrier, will produce the ultimate function Therefore, the baseband signal can be

thought of as the encoded signal, but before any particular channel or center frequency has been chosen This means that the baseband signal is identical for every channel Because the baseband encoding is the most complicated part of the radio—it does the business of giving the signal its flavor, if you will, the part of a radio that encodes or modulates the

signal is also called the baseband

In digital systems, which 802.11 belongs to, phase modulation is known by the term phase

shift keying (PSK), representing that the phase is shifted abruptly because of the digital

-1.0

-0.6

-0.2

0.2

0.6

1.0

-1.0

-0.6

-0.2

0.2

0.6

1.0

-1.0

-0.6

-0.2

0.2

0.6

1.0

Carrier = A cos [2 p f c t ]

Data Signal (between -1 and 1)

Final Modulated Signal = A cos [2 p (f c + Data) t ]

Figure 5.15: Analog Frequency Modulation

nature of the incoming signal, and the shift is “keyed” by the digital data Understanding these terms is not necessary to understanding Wi-Fi, but it can offer some insight into why some radios do better in certain environments than others

5.5.1.1 1Mbps

For 1Mbps, 802.11 uses what is called binary phase shift keying (BPSK) This simply

means that the phase is shifted forward by 180 degrees for a 1 bit in the data, and left

-1.0

-0.6

-0.2

0.2

0.6

1.0

-1.0

-0.6

-0.2

0.2

0.6

-1.0

-0.6

-0.2

0.2

0.6

Carrier = A cos [2 p f c t ]

Data Signal (between -1 and 1)

NOTE: Because the phase modulation maps the incoming signal into the range of 180 degrees, plus or minus, the encoded signal can only differentate between a zero and non-zero value -1 and 1 become -180 degrees and 180 degrees, which are equal.

-1.0

-0.6

-0.2

0.2

0.6

Phase Modulated Signal = A cos [2 p f c t + Data]

Frequency Signal = A cos [2 p (f c + Data) t ]

Figure 5.16: Frequency versus Phase Modulation

The modulating signal, however, is not just the stream of bits that make up the frame

Additional work goes in to prepare the incoming bitstream for transmission so that it will better survive the sometimes nasty conditions of the RF channel Each incoming data bit is

mapped to 11 transmission bits These outgoing 11 bits are called, together, one symbol, and each of the eleven bits is individually called a chip The process of mapping bits to chips is known spreading, the term deriving from the effect the mapping has of spreading out the

frequency range the signal takes on (Or, one can think of the process as spreading the

information contained in the original data bit over the various chip bits of the symbol.) This expanding of one data bit to 11 chip “bits” is done to protect the signal from various types

0°

180°

90°

-90°

A = 1

in-phase axis (I)

quadrature axis (Q)

x

Figure 5.17: Binary Phase Shift Keying

representation Don’t let it be intimidating: this is just the polar coordinate system

mentioned previously, with each X representing the modulation of the carrier represented by

each bit Notice that the distance from the origin A is always 1: BPSK does not use

amplitude modulation at all

of interference, and the mapping is very specific sequence known as a Barker sequence The

sequence used happens to be

+1, −1, +1, +1, −1, +1, +1, +1, −1, −1, −1

where +1 represents the 1 bit and −1 represents the 0 bit This sequence might seem to be random, but it was chosen because it possesses an important real-world property As the signal encoded with this Barker sequence reflects off surfaces, it will be delayed a bit relative to the original signal, and each delayed reflection that hits the receiver will appear

to be added together, causing the received signal to appear blurred out as the sequences overlap The important mathematical property of the Barker sequence is that the

autocorrelation, or the sum of the element-wise product of the sequence and any delayed version of the sequence, will have a strong peak when no delay is present and will be close

to zero otherwise This allows the receiver to use math to hunt out the main signal—the part that comes directly from the transmitter and not off of reflected surfaces—and filter out the echoes to get a cleaner signal Furthermore, the increasing of the rate by a factor of 11 provides redundancy in time, which causes spreading in frequency to the final 20MHz bandwidth The advantage of spreading the signal over a wider range of frequencies is that many interference sources are narrow-band and will then affect only a small part of the encoded signal, rather than the entire signal, and the receiver may still be able to recover

-1 0 1

Eleven-chip Barker Sequence

+1

-1 -1 -1

-2 11

Autocorrelation of Eleven-chip Barker Sequence

Figure 5.18: The 11-Chip Barker Code

Two more points: the data bits are differentially encoded, meaning that if two bits to send are 11, the chip sequence is the Barker sequence, followed by the Barker sequence

multiplied by −1 The differential encoding is used to make it unnecessary for the receiver

to know whether 0 degrees is a 0 bit and 180 degrees is a 1 bit, or vice versa Also, the data

bits go through a process known as scrambling, which ensures that data that is made of

predominantly one value—such as a string of zeros—has enough variation over the air to prevent the signal from not changing enough and drifting to one side or the other of the

center frequency, something which makes the signal harder to transmit or receive The

process is called scrambling because the bits are modified with a pseudorandom sequence— there is no security aspect in this, however The scrambled bits end up becoming the ones that are then spread out into the 11-chip symbols

5.5.1.2 2Mbps

The 2Mbps data rate is very similar to the 1Mbps data rate The main difference is that the data bits are taken pairwise (after scrambling), and encoded so that two-bit pairs map to

11-chip symbols This doubles the data rate: the two bits are packed in by encoding both bits into one symbol, with the symbol taking the same time as a 1Mbps one Looking at the

are equally spaced around the circle—at degrees 0, 90, 180, and 270 (-90) In this sense, the two bits are packed in by splitting “space”, meaning room in the constellation, rather than sending one after the other by splitting “time”

The downside to packing in two bits per symbol is that the distance between the

constellation points on the symbol has gone down This is important, because noise

shows up at the receiver as an uncertainly about whether a given symbol belongs as one of the—in this case, four Xs If there are only two possible symbols, as with the 1Mbps rate, then the receiver’s value would have had to have drifted very far to cause a mistake With four possible symbols, however, the received symbol need not drift as far to cause an error This is what was being referred to earlier when discussing how lower data rates are more robust, whereas higher data rates require increased fidelity The more noise, the worse the higher data rates do, and the more mistakes they make In 802.11, one mistake in choosing

5.20)

Therefore, the 2Mbps data rate requires both a higher absolute signal strength and a higher SNR to be received, and thus will not carry with quite the same range as 1Mbps rates will

5.5.1.3 5.5Mbps and 11Mbps

The 5.5Mbps data rate was the first one introduced in the 802.11b amendment itself

Recognizing that 2Mbps was not fast, compared with the predominant 10Mbps wireline

speeds from 10BASE-T Ethernet, the IEEE introduced the 5.5Mbps and 11Mbps data rates

To get to the faster data rate, IEEE decided not to continue splitting space by adding more points to the constellation Instead, they looked at the 11 chips, and decided to pack more bits in by changing the data bits throughout the 11-chip sequence, thus splitting time Instead of assigning one or two bits for the entire 11-chip sequence, both 5.5Mbps and 11Mbps use an eight-chip sequence (still sent out at 11 megachips/second), and then map either four or eight bits to each eight-chip symbol These eight-chip symbols are QPSK encoded, and the (complex) value of each of the eight chips is determined by four bit-pairs that are input The particular formula used to determine the eight chip values from the eight

input bits is designed to increase the reliability of the signal, and is a type of complementary

code keying (CCK)

The 11Mbps rate maps the eight data bits per symbol to the four bit-pairs directly The 5.5Mbps data rate is produced by using only four data bits to get the eight-bit input to the formula by using a specified mapping up front, adding greater redundancy

Because of the greater redundancy, 5.5Mbps has a longer range and less SNR requirements than 11Mbps

0°

180°

90°

-90°

A = 1

in-phase axis (I)

quadrature axis (Q)

x x

x

data = 01

data = 11 data = 10

Figure 5.19: Quadrature Phase Shift Keying

5.5.1.4 Short and Long Preambles

802.11b allows the transmitter to choose from either a short or long preamble for the 2, 5.5, and 11Mbps data rates The intent of allowing a short preamble, being almost exactly half

as short in time as the long preamble will be to free up some additional airtime, at the risk

of slightly decreasing the chances that there will be enough time for a radio to lock onto the signal In the early days of 802.11b-only networking, this statement may have been more true Now, however, most of the distinction is lost, and short preambles should always be recommended, unless old legacy devices are in use Most of the issues with short preambles now are from those old devices not accepting short preambles

5.5.2 802.11a and 802.11g

802.11a and 802.11g expanded the data rates and network efficiency significantly, leading to

a top data rate of 54Mbps 802.11a—for the 5GHz band—and 802.11g—for the 2.4GHz band—are nearly identical except for the band in use and some additional rules Their

introduction was a turning point in Wi-Fi, allowing the designers to use a newer, different

0°

180°

90°

-90°

A = 1

in-phase axis (I)

error circles

This symbol will be received correctly

This symbol is ambiguous and will probably be received incorrectly

quadrature axis (Q)

x x

x x

*

*

data = 00 data = 01

data = 11 data = 10

Figure 5.20: Symbol Error

way of encoding signals than before that would greatly enhance the speed of the network,

as well as the robustness

The challenge to 802.11 designers was to increase the data rates by packing more bits into the channel, but without requiring the signal itself to fluctuate in time so fast that delay effects prevented the radio from working in real environments In fact, if there was a way to make the signal even more robust to delay, that would be useful in getting Wi-Fi into more environments with more reliability

In the end, the designers settled on one scheme and gave them two letters The two radios use the same method to encode more data per symbol This method works by dividing up the channel from one 20MHz block to dozens of very small blocks, each of which becomes

its own miniature channel This new technique is called orthogonal frequency division

multiplexing (OFDM) The frequency division part is rather straightforward: dividing the

20MHz channel into 48 of those small channels (subcarriers), separated 20MHz/64 =

5/16th MHz apart allows the 20MHz band to be used more efficiently (It is important to note that the subcarriers always belong to the same transmission, and are not to be thought

of as separate, usable channels.) The orthogonal aspect is that the subcarriers are encoded and spaced so that the sidelobes, or parts of the subcarrier that would ordinarily interfere with adjacent signals) do not interfere with adjacent subcarriers here Why create more carriers? 802.11b, at 1Mbps, has 1-microsecond symbols, which are relatively short in time

To get to 11Mbps, 802.11b had to shrink the symbol to 73% the original duration and vary the data within the symbol for each 90-nanosecond chip Trying this for 54Mbps would require either varying the data every 18 nanoseconds, or making major sacrifices on the redundancy Either way, the signal would not be able to travel through most environments very well, and Wi-Fi would not be able to transmit at high speeds past a few feet However,

by spreading the data out across 48 subcarriers, the data rate on each subcarrier is dropped back to something similar to the 1Mbps 802.11b data rate—1.125Mbps Bumping up the modulation to six scrambled bits per symbol then allows the symbol to be held without fluctuation for longer and reduces the bandwidth of the subcarrier to its final value, resulting

in a growth from 1 microsecond symbols to 4 microseconds By packing in more bits per

Hz, the signal can become more resilient over time

This advance was quite exciting for its time, and is still one of the two major underpinnings for modern 802.11n radios

Table 5.12 shows the data rates available to 802.11ag There are now eight data rates unique

to 802.11ag

The two additions to 802.11b for each subcarrier are the growth of the constellations and

the use of an error correction code built into the radio The first part, the constellation

expansion, builds upon the concepts used to expand from 1Mbps to 2Mbps to pack more

bits in The constellation points are no longer on a circle; rather, they are spaced evenly on

shows the two constellations—this time, the labels for which bits go to which constellation point are left off for clarity

As you may notice, the use of four different modulation schemes—BPSK, QPSK, 16-QAM, and 64-QAM—lead to four different numbers of coded bits per symbol, but there are eight, not four, data rates To allow for two data rates for the same modulation type, 802.11ag

introduces the error correction code Error correction codes are methods of expanding digital data into something with more bits than the original in such a way that some of those

expanded bits can be lost without causing a loss in the original data In a pure sense, this is the opposite goal from data compression, where redundant bits are removed, rather than

added The extra bits are wasteful if there are no errors in the data, but if there are errors in the data, the code will protect the data from loss Redundancy in wireless, as we have seen, is

a good thing to have We’ve seen spreading sequences already, and error correction codes can

be thought of as a way to spread the bits as well, but over time rather than over frequencies (Of course, frequency and time are two sides of the same coin.)

The simplest error correction codes are just to repeat bits of the data A bit stream of

101101 can be doubled, to produce 101101101101 This stream protects against any one bit

being lost Let’s say that the stream arrives at the receiver as 101x01101101, where x is the

lost bit The receiver can clearly recover the lost bit, by looking at the copy that makes up the second half of the transmission Doubling protects the stream from up to 50% loss, if the right 50% is lost, but can fail at two losses if the two bits lost are from the same source Because the ability to correct for errors depends not only on the number of bits lost, but the positions of the lost bits, doubling makes for a very poor error-correction code in practice

To protect against exactly one bit loss in the most efficient manner possible, just sum the

Table 5.12: The 802.11ag data rates

Subcarrier

Coding Rate