Bsi bs en 60332 1 1 2004 + a1 2015

BRITISH STANDARD BS EN 60332 1 1 2004 Tests on electric and optical fibre cables under fire conditions — Part 1 1 Test for vertical flame propagation for a single insulated wire or cable — Apparatus T[.]

Trang 1

BRITISH STANDARD BS EN

60332-1-1:2004

Tests on electric and

optical fibre cables

under fire conditions —

Part 1-1: Test for vertical flame

propagation for a single insulated wire

or cable — Apparatus

The European Standard EN 60332-1-1:2004 has the status of a

British Standard

ICS 13.220.40; 29.020: 29.060.20

BS EN 60332-1-1:2004 +A1:2015

Trang 2

BS EN 60332-1-1:2004+A1:2015

ISBN 978 0 580 82668 9

Amendments/corrigenda issued since publication

31 December 2015 Implementation of IEC amendment 1:2015 with

CENELEC endorsement A1:2015

This British Standard was

published under the authority

of the Standards Policy and

Strategy Committee on

18 January 2005

Institution 2015

Published by BSI Standards

Limited 2015

National foreword

This British Standard is the UK implementation of

EN 60332-1-1:2004+A1:2015 It is identical to IEC 60332-1-1:2004, incorporating amendment 1:2015 It supersedes BS EN 60332-1-1:2004, which will be withdrawn on 1 September 2018

The start and finish of text introduced or altered by amendment is indicated

in the text by tags Tags indicating changes to IEC text carry the number

of the IEC amendment For example, text altered by IEC amendment 1 is indicated by 

The UK participation in its preparation was entrusted by Technical Committee GEL/20, Electric cables, to Subcommittee GEL/20/18, Electric Cables – Fire testing

A list of organizations represented on this subcommittee can be obtained on request to its secretary

The publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application

Compliance with a British Standard cannot confer immunity from legal obligations.

Trang 3

EUROPEAN STANDARD EN 60332-1-1

NORME EUROPÉENNE

CENELEC

European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

Ref No EN 60332-1-1:2004 E

English version

Tests on electric and optical fibre cables under fire conditions

Part 1-1: Test for vertical flame propagation for a single insulated wire or cable

-Apparatus

(IEC 60332-1-1:2004)

Essais des câbles électriques

et à fibres optiques soumis au feu

Partie 1-1: Essai de propagation verticale

de la flamme sur un conducteur

ou câble isolé

-Appareillage d'essai

(CEI 60332-1-1:2004)

Prüfungen an Kabeln, isolierten Leitungen und Glasfaserkabeln im Brandfall

Teil 1-1:Prüfung der vertikalen Flammenausbreitung an einer Ader, einer isolierten Leitung oder einem Kabel -Prüfgerät

(IEC 60332-1-1:2004)

This European Standard was approved by CENELEC on 2004-09-01 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member

This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom

EN 60332-1-1:2004+A1

October 2015

Trang 4

EN 63302-1-1:0240 - - 2

Foreword

The text of document 20/696/FDIS, future edition 1 of IEC 60332-1-1, prepared by IEC TC 20, Electric cables, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as

EN 60332-1-1 on 2004-09-01

This European Standard, together with EN 60332-2-1, supersedes EN 50265-1:1998

The following dates were fixed:

– latest date by which the EN has to be implemented

at national level by publication of an identical

– latest date by which the national standards conflicting

Annex ZA has been added by CENELEC

Endorsement notice

The text of the International Standard IEC 60332-1-1:2004 was approved by CENELEC as a European Standard without any modification

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60332-1-2 NOTE Harmonized as EN 60332-1-2:2004 (not modified).

IEC 60695-2-4/0 NOTE Harmonized as EN 60695-2-4/0:1993 (not modified).

Page 2

EN 60332−1−1:2004

Page 2

BS EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004+A1:2015

Trang 5

Page 3

BS EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004/A1:2015

2

European foreword

The text of document 20/1590/FDIS, future IEC 60332-1-1:2004/A1, prepared by IEC/TC 20 "Electric

cables" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as

EN 60332-1-1:2004/A1:2015

The following dates are fixed:

• latest date by which the document has to be implemented at

national level by publication of an identical national

standard or by endorsement

(dop) 2016-06-01

• latest date by which the national standards conflicting with

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights CENELEC [and/or CEN] shall not be held responsible for identifying any or all such

patent rights

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment

Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC)

Endorsement notice

The text of the International Standard IEC 60332-1-1:2004/A1:2015 was approved by CENELEC as a

European Standard without any modification

In the Bibliography of EN 60332-1-1:2004, the following note has to be added for the standard indicated:

ISO 13943 NOTE Harmonized as EN ISO 13943

In the Bibliography of EN 60332-1-1:2004, the following note has to be deleted for the standard indicated:

IEC 60695-2-4/0 NOTE Harmonized as EN 60695-2-4/0:1993 (not modified)

Foreword to amendment A1

Trang 6

Page 4

BS EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004+A1:2015

CONTENTS

1 Scope �� 5

2 Normative references �� 5

3 Terms and definitions �� 5

4 Test apparatus �� 5 4�1 Components �� 5 4�2 Metal enclosure �� 6 4�3 Ignition source �� 6 4�4 Chamber �� 6 Annex ZA (normative) Normative references to international publications with their

corresponding European publications �� 8 Bibliography �� 9



Trang 7

063-23-11  IE:C002 4 – 4 –

TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES

UNDER FIRE CONDITIONS – Part 1-1: Test for vertical flame propagation for a single insulated wire or cable – Apparatus

1 Scope

This part of IEC 60332 specifies the test apparatus for testing the resistance to vertical flame

propagation for a single vertical electrical insulated conductor or cable, or optical fibre cable,

under fire conditions

The procedure, together with an informative annex of recommended requirements for

performance, is given in IEC 60332-1-2

2 Normative references

The following referenced documents are indispensable for the application of this document

For dated references, only the edition cited applies For undated references, the latest edition

of the referenced document (including any amendments) applies

IEC 60695-4, Fire hazard testing – Part 4: Terminology concerning fire tests

IEC 60695-11-2, Fire hazard testing – Part 11-2: Test flames – 1 kW nominal pre-mixed

flame – Apparatus, confirmatory test arrangement and guidance

IEC Guide 104, The preparation of safety publications and the use of basic safety publications

and group safety publications

3 Terms and definitions

For the purposes of this document, the following definition applies The definition is taken

from IEC 60695-4

3.1

ignition source

source of energy that initiates combustion

[IEC 60695-4:1993, definition 2.76]

4 Test apparatus

4.1 Components

The test apparatus shall comprise the following:

a) a metallic screen (4.2);

b) an ignition source (4.3);

c) a suitable chamber (4.4)

Page 4

EN 60332−1−1:2004

1 Scope

from IEC 60695-4

3.1

ignition source

[IEC 60695-4:1993, definition 2.76]

4.1 Components

Page 4

EN 60332−1−1:2004

1 Scope

from IEC 60695-4

3.1

ignition source

[IEC 60695-4:1993, definition 2.76]

4.1 Components

Page 4

EN 60332−1−1:2004

Page 5

BS EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004+A1:2015

[SOURCE: ISO 13943:2008, 4�189]



a) a metal enclosure (4�2);



Trang 8

063-23-11  IE:C002 4 – 5 –

4.2 Metallic screen

A metallic screen (1 200 ± 25) mm high, (300 ± 25) mm wide and (450 ± 25) mm deep with

open front and closed top and bottom, (see Figure 1), shall be used

4.3 Ignition source

The ignition source shall comply with IEC 60695-11-2, which includes a method of

confirmation of the test flame, except that the burner shall be fed with technical grade

propane of greater than 95 % purity

NOTE IEC 60695-11-2 specifically refers to the need to study also IEC 60695-2-4/0.

4.4 Chamber

The metallic screen and ignition source shall be contained within a suitable chamber,

substantially free from draughts during the test duration, but with facilities for disposing of

noxious gases resulting from burning The chamber shall be maintained at a temperature of

(23 ± 10) °C

NOTE 1 If the requirement for the draught-free closed area is met by the use of a standard fume cupboard, it

must be capable of independent operator-control of the extractor fan such as to permit operation with the extractor

"OFF" Some fume cupboards may not be supplied with this facility.

NOTE 2 If a fume cupboard is used as the draught-free test area, the following safe operating practice is

recommended:

a) turn off extractor fan, seal the outlet;

b) pull down front door of fume cupboard to leave a gap sufficient to manipulate burner into position;

c) ensure operator is protected;

d) do not move the door of the fume cupboard during the test;

e) at the end of the test evacuate the fume cupboard fully before opening the door.

Page 5

EN 60332−1−1:2004

Page 6

BS EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004+A1:2015

4.2 Metal enclosure

A metal enclosure (1 200 ± 25) mm high, (300 ± 25) mm wide and (450 ± 25) mm deep with

open front and closed top and bottom, (see Figure 1), shall be used, in order to protect the test

sample from draughts� It shall be constructed of rigid sheet metal�

4.3 Ignition source

The ignition source shall comply with IEC 60695-11-2, which includes a method of confirmation

of the test flame, except that the laboratory fumehood/chamber shall comply with 4�4�

4.4 Chamber

The metal enclosure and ignition source shall be contained within a suitable chamber,

substantially free from draughts during the test duration, but with facilities for disposing of

noxious gases resulting from burning� The chamber shall be maintained at a temperature of

(23 ± 10) °C�



Trang 9

Page 7

BS EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004+A1:2015

IEC 60332-1-1:2004/AMD1:2015 – 3 –

4.4 Chamber

In line 1 replace 'metallic screen' by 'metal enclosure'

Figure 1 - Test apparatus – Metallic screen

Replace the existing Figure 1 including its title by the following new Figure 1 and title:

Dimensions in millimetres

Key

1 front open space (all other sides closed)

Figure 1 – Test apparatus – Metal enclosure

Bibliography

Add the following new reference:

ISO 13943, Fire safety – Vocabulary

Delete the reference to IEC 60695-2-4/0 and its footnote

_

IEC

300 ±25





Trang 10

3 - -

Annex ZA

(normative)

Normative references to international publications with their corresponding European publications

The following referenced documents are indispensable for the application of this document For dated

references, only the edition cited applies For undated references, the latest edition of the referenced

document (including any amendments) applies

NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.

IEC 60695-4 -1) Fire hazard testing

Part 4: Terminology concerning fire tests EN 60695-4 1995

2)

IEC 60695-11-2 -1) Part 11-2: Test flames - 1 kW nominal

pre-mixed flame - Apparatus, confirmatory test arrangement and guidance

EN 60695-11-2 2003 2)

IEC Guide 104 -1) The preparation of safety publications

and the use of basic safety publications and group safety publications

1) Undated reference.

2) Valid edition at date of issue.

Page 7

EN 60332−1−1:2004

Page 8

BS EN 60332-1-1:2004+A1:2015

EN 60332-1-1:2004+A1:2015

Tiêu đề	Tests on electric and optical fibre cables under fire conditions
Trường học	British Standards Institution
Chuyên ngành	Standards
Thể loại	British standard
Năm xuất bản	2004
Thành phố	Brussels

Định dạng
Số trang	14
Dung lượng	558,62 KB