Bsi bs en 60264 2 1 1996 (2003)

BRITISH STANDARD BS EN 60264 2 1 1996 IEC 264 2 1 1989 Incorporating Amendment No 1 BS 7584 2 1 1992 renumbered and Amendment No 2 Packaging of winding wires — Part 2 Cylindrical barrelled delivery sp[.]

Incorporating Amendment No 1

BS 7584-2.1:1992 renumbered and Amendment No 2

Packaging of winding

wires —

Part 2: Cylindrical barrelled delivery

spools —

Section 2.1 Basic dimensions

The European Standard EN 60264-2-1:1994, incorporating

amendment A1:2003, has the status of a British Standard

ICS 29.060.10

12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:

BS EN 60264-2-1:1996

This British Standard, having

been prepared under the

direction of the Cables and

Insulation Standards Policy

Committee, was published

under the authority of the

Standards Board and comes

into effect on

15 August 1992

© BSI 26 November 2003

The following BSI references

relate to the work on this

British Standard:

Committee reference CIL/55

Draft announced in

BSI News May 1992

ISBN 0 580 21023 5

Committees responsible for this British Standard

The preparation of this British Standard was entrusted by the Cables and Insulation Standards Policy Committee (CIL/-) to Technical Committee CIL/55, upon which the following bodies were represented:

British Cable Makers Confederation British Non-ferrous Metals Federation British Railways Board

Covered Conductors Association EEA (the Association of Electronics, Telecommunications and Business Equipment Industries)

Electrical and Electronic Insulation Association Electronic Components Industry Federation Transmission and Distribution Association (BEAMA Ltd.)

Amendments issued since publication

Amd No Date Comments

9048 May 1996

14833 26 November 2003 Replacement of Table 1 and Figure 1

`,,`-`-`,,`,,`,`,,` -© BSI 26 November 2003 i

Contents

Page Committees responsible Inside front cover

Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications 5 Figure 1 — Cylindrical barrelled delivery spools 4 Table 1 — Dimensions and tolerances for cylindrical barrelled

BS EN 60264-2-1:1996

National foreword

This British Standard has been prepared by Technical Committee GEL/55 (formerly CIL/55) and is the English language version of

EN 60264-2-1:1994 Packaging of winding wires — Part 2: Cylindrical barrelled

delivery spools — Section 1: Basic dimensions, including amendment A1:2003,

published by the European Committee for Electrotechnical Standardization (CENELEC) It is identical with IEC 264-2-1:1989, including amendment 1:2003, published by the International Electrotechnical Commission (IEC)

BS EN 60264, of which there are four Parts, deals with the packaging of winding wires Part 1 covers containers, Part 2 covers cylindrical barrelled delivery spools, Part 3 covers taper barrelled delivery spools and Part 4 covers methods of test This British Standard is one of a series dealing with insulated wires used for windings in electrical equipment, which comprises the following three groups

IEC 851, Methods of test for winding wires;

IEC 317, Specifications for particular types of winding wires;

IEC 264, Packaging of wires.

NOTE BS 6811 Winding wires Part 0:1993 General introduction and list of Parts lists the various

Sections of BS 6811 and BS 7584 against the corresponding Parts of the IEC standards listed above Some or all of these IEC standards will be adopted as BS ENs in due course and the relevant Parts of

BS 6811 and BS 7584 will be renumbered as BS ENs.

This publication does not purport to include all the necessary provisions of a contract Users are responsible for its correct application

Compliance with a British Standard does not of itself confer immunity from legal obligations.

Summary of pages

This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 5 and a back cover

The BSI copyright notice displayed in this document indicates when the document was last issued

EUROPÄISCHE NORM + A1

October 2003

ICS 29.060.10

English version

Packaging of winding wires — Part 2: Cylindrical barrelled delivery spools —

Section 1: Basic dimensions

(includes amendment A1:2003) (IEC 60264-2-1:1989/A1:2003)

Conditionnement des fils de bobinage —

Partie 2: Bobines de livraison à fût de forme

cylindrique —

Section 1: Dimensions de base

(inclut l’amendement A1:2003)

(CEI 60264-2-1:1989)

Verpackung von Wickeldrähten — Teil 2: Lieferspulen mit zylindrischem Kern — Hauptabschnitt 1: Maße (enthält Änderung A1:2003) (IEC 60264-2-1:1989)

This European Standard was approved by CENELEC on 1994-09-01

Amendment A1 was approved by CENELEC on 2003-10-01 CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member

This European Standard exists in three official versions (English, French, German) A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom

CENELEC

European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B-1050 Brussels

© 2003 CENELEC — All rights of exploitation in any form and by any means reserved worldwide for CENELEC members Ref No EN 60264-2-1:1994 + A1:2003 E

`,,`-`-`,,`,,`,`,,` -EN 60264-2-1:1994

© BSI 26 November 2003

2

Foreword

The text of the International Standard

IEC 264-2-1:1989, prepared by IEC TC 55, Winding

wires, was approved by CENELEC as HD 46.2.1 S1

on 1990-05-01

This Harmonization Document was submitted to

the formal vote for conversion into a European

Standard and was approved by CENELEC as

EN 60264-2-1 on 1994-09-01

The following date was fixed:

Annexes designated “normative” are part of the

body of the standard In this standard, Annex ZA is

normative Annex ZA has been added by

CENELEC

Foreword to amendment A1

The text of document 55/830/FDIS, future amendment 1 to IEC 60264-2-1:1989, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60264-2-1:1994

on 2003-10-01

The following dates were fixed:

— latest date by which the EN

has to be implemented at

national level by publication

of an identical national

standard or by endorsement (dop) 1995-10-15

— latest date by which the amendment has to be implemented at national level by publication of an identical national standard

or by endorsement (dop) 2004-07-01

— latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2006-10-01

`,,`-`-`,,`,,`,`,,` -© BSI 26 November 2003 3

1 Scope

This standard specifies the basic dimensions for cylindrical barrelled delivery spools for winding wires

2 Object

To standardize the dimensions of cylindrical barrelled delivery spools

3 Dimensions

The dimensions and tolerances for cylindrical barrelled delivery spools are given in Table 1 in accordance with Figure 1

NOTE Figure 1 is given to identify the dimensions specified and is not intended to show any particular construction.

Table 1 — Dimensions and tolerances for cylindrical barrelled delivery spools

4 Material

Requirements are to be stated in the purchaser’s order

Spool

type

Dimensions

mm

d1 d2 d3 b d4 d5 c d6 a L1 l2 aa l1 z y e1 r

40 40 25 11 +0,15 15 — 1.5 50 38 ±0,10 0,75 14 0,4 0,08 — 1

50 50 32 11 +0,15 15 — 1.5 50 38 ±0,15 0,75 16 0,4 0,10 — 1

63 63 40 11 +0,15 15 — 2 63 49 ±0,15 1,0 18 0,4 0,15 — 1,6

80 80 50 16 +0,20 24 7 2 80 64 ±0,15 1,0 20 0,6 0,15 20 2

100 100 63 16 +0,20 24 7 2 100 80 ±0,20 1,0 22 0,6 0,20 20 2

125 125 80 16 +0,20 24 7 3 125 100 ±0,20 1,5 25 0,6 0,20 20 3

160 160 100 22 +0,20 34 13 3 160 128 ±0,20 1,5 28 0,6 0,30 32 3

200 200 125 22 +0,20 34 13 3 200 160 ±0,30 1,5 32 0,6 0,30 32 4

250 250 160 22 +0,20 34 13 4 200 160 ±0,40 2,0 36 1,0 0,40 32 5

355 355 224 36 +0,50 60 26 5 200 160 ±0,40 2.5 40 1,2 0,5 80 5

500 500 315 36 +0,50 60 26 10 250 180 ±0,50 5.0 40 1,6 0.7 80 5

710 710 500 51 +0,50 80 26 15 250 180 ±0,80 7.5 45 2,0 1.0 140 6

1 000 1 000 800 51 +0,50 80 26 26 250 180 ±1,00 13 50 3,0 1.5 140 6

a Spools without holes can be ordered if agreed between supplier and purchaser If bore d6 is wanted, quantity and position of

bore d6 shall be according to agreement.

b For spool types 250 and 710, a central bore diameter d3 of (36 mm) may be used if agreed between supplier and purchaser.

c Number of bore d5 for spools K 80 and K 100: minimum 1 bore per side.

Number of bore d5 for spools from K 125: minimum 2 bore per side.

For spools K 80 and K 100 the bore d5 can be designed as a blind hole.

+0,5 0

`,,`-`-`,,`,,`,`,,` -EN 60264-2-1:1994

Figure 1 — Cylindrical barrelled delivery spools

© BSI 26 November 2003 5

Annex ZA (normative)

Other international publications quoted in this standard with the references

of the relevant European publications

This European Standard incorporates by dated or undated reference, provisions from other publications These normative references are cited at the appropriate places in the text and the publications are listed hereafter For dated references, subsequent amendments to or revisions of any of these publications apply

to this European Standard only when incorporated in it by amendment or revision For undated references the latest edition of the publication referred to applies

NOTE When the international publication has been modified by CENELEC common modifications, indicated by (mod), the relevant EN/HD applies.

IEC publication Date Title EN/HD Date

264 series Packaging of winding wires EN 60264 series

317 series Specifications for particular types of winding wires HD 555

EN 60317 seriesseries

851 series Methods of test for winding wires HD 490

EN 60851 seriesseries

`,,`-`-`,,`,,`,`,,` -BS EN

60264-2-1:1996

IEC 264-2-1:

1989

BSI

389 Chiswick High Road

London

W4 4AL

BSI — British Standards Institution

BSI is the independent national body responsible for preparing British Standards It presents the UK view on standards in Europe and at the international level It is incorporated by Royal Charter

Revisions

British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions

It is the constant aim of BSI to improve the quality of our products and services

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover

Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400

BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards

Buying standards

Orders for all BSI, international and foreign standards publications should be addressed to Customer Services Tel: +44 (0)20 8996 9001

Fax: +44 (0)20 8996 7001 Email: orders@bsi-global.com Standards are also available from the BSI website at http://www.bsi-global.com

In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested

Information on standards

BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service Various BSI electronic information services are also available which give details on all its products and services Contact the Information Centre

Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: info@bsi-global.com Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards For details

of these and other benefits contact Membership Administration

Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001

Email: membership@bsi-global.com

Information regarding online access to British Standards via British Standards Online can be found at http://www.bsi-global.com/bsonline

Further information about BSI is available on the BSI website at http://www.bsi-global.com

Copyright

Copyright subsists in all BSI publications BSI also holds the copyright, in the

UK, of the publications of the international standardization bodies Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI

This does not preclude the free use, in the course of implementing the standard,

of necessary details such as symbols, and size, type or grade designations If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained

Details and advice can be obtained from the Copyright & Licensing Manager Tel: +44 (0)20 8996 7070 Fax: +44 (0)20 8996 7553

Email: copyright@bsi-global.com