Designation D4596 − 09 (Reapproved 2015) Standard Practice for Collection of Channel Samples of Coal in a Mine1 This standard is issued under the fixed designation D4596; the number immediately follow[.]
Trang 1Designation: D4596−09 (Reapproved 2015)
Standard Practice for
This standard is issued under the fixed designation D4596; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision A number in parentheses indicates the year of last reapproval A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1 Scope
1.1 This practice describes procedures for collecting a coal
sample from a channel extending from top to bottom in the face
of a coal seam in a mine
1.2 The values stated in SI units are to be regarded as
standard No other units of measurement are included in this
standard
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use It is the
responsibility of the user of this standard to establish
appro-priate safety and health practices and determine the
applica-bility of regulatory limitations prior to use For specific
precautionary information, seeNote 2.
2 Referenced Documents
2.1 ASTM Standards:2
D121Terminology of Coal and Coke
D388Classification of Coals by Rank
D2234/D2234MPractice for Collection of a Gross Sample
of Coal
D2796Terminology for Megascopic Description of Coal
and Coal Seams and Microscopical Description and
Analysis of Coal(Withdrawn 1995)3
D4371Test Method for Determining the Washability
Char-acteristics of Coal
3 Summary of Practice
3.1 At selected sites in the mine the face of the seam is
cleaned of weathered coal and debris and the face is evened A
channel of uniform horizontal cross section is cut from the coal seam and the coal therefrom is collected for analysis and testing
4 Significance and Use
4.1 A properly collected face channel sample that includes the total coal bed interval provides a sample that is a repre-sentative cross section of the coal bed at the point of sampling Channel samples are taken for subsequent testing needed for evaluation of coal quality and characterization for commercial evaluations, for planning of mining operations to maintain coal quality, for the determination of coal rank in accordance with Classification D388, and for geologic coal resource studies
N OTE 1—Because of the potential for lateral variability, a sample may not represent the quality of the coal bed at another sample point The reliability of the data generated from channel samples is dependent on the number and spacing of the sample points and the variability of the coal characteristics in a given area.
N OTE 2—Sampling of the mine product for these purposes is unsatis-factory because of contamination of the product with out-of-seam material, selective mining of parts of a seam, inability to obtain samples from one or more specific locations in the mine, or other incompatibility
of the purpose of sampling with the mining practice Conversely, channel samples should not be used for evaluation of the quality of commercial shipments of the mine product, which should be sampled in accordance with Methods D2234/D2234M
5 Apparatus
5.1 Steel Measuring Tape, not less than 3 m (8 ft) long 5.2 Miner’s Pick or Similar Tool, with file for sharpening.
Other devices may be used such as a pneumatically operated chain saw with tungsten carbide teeth
5.3 Brush or Broom, for removing loose particles on the
coal face
5.4 Chalk.
5.5 Sample Containers With Closures—If the sample is to be
used for determination of inherent moisture, the container shall
be such that less than 0.05 % of the sample weight is lost between the time of sealing the container with sample and the time of opening for preparation of the sample for analysis Steel airtight containers with polyethylene bag liners have been
1 This practice is under the jurisdiction of ASTM Committee D05 on Coal and
Coke and is the direct responsibility of Subcommittee D05.18 on Classification of
Coals.
Current edition approved Sept 1, 2015 Published September 2015 Originally
published approved in 1986 Last previous edition approved in 2009 as D4596 – 09.
DOI: 10.1520/D4596-09R15.
2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 The last approved version of this historical standard is referenced on
www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959 United States
Trang 2found to be satisfactory for this purpose For other purposes,
bags made of a strong cloth and lined with a polyethylene bag
may be suitable
5.6 Ground Cloth—Canvas tarpaulin or heavy-duty plastic
sheet about 3 by 3 m (10 by 10 ft) If the purpose of sampling
includes the determination of inherent moisture, the sheet shall
be of low water solubility and permeability, such as
polyeth-ylene or oilcloth
5.7 Tags and Pen, for sample identification and for marking.
5.8 Shovel.
5.9 Notebook and Pencil, or other means for record keeping.
6 Planning of Sampling
6.1 Considerations regarding weathered coal and inherent
moisture:
Weathered coal is unsuitable for inclusion in channel samples
collected to secure fresh and unaltered material Weathered
coal typically contains anomalously low total moisture, yields
low calorific value (dry and moisture-and-ash-free basis), and
also produces atypical results for other tests It does not reflect
unaltered in-situ coal properties, cannot be used for
classifica-tion according to rank, and does not give accurate estimates of
typical as-mined moisture
6.1.1 Obvious indications of weathering include, but are not
limited to: (1) any discoloration of broken coal surfaces or
cleats, (2) presence of sulfate minerals resulting from oxidation
of pyrite, (3) presence of gypsum (calcium sulfate) crystals,
and (4) presence of dust, cracked and crazed coal surfaces, or
a fragmented condition of the coal blocks resulting from loss of
inherent moisture
6.1.2 It is often useful to collect samples containing their
full complement of inherent moisture, but that condition may
not always be readily discernable A simple field test can be
used to qualitatively identify seemingly fresh coal that has lost
some inherent moisture but has not yet obviously weathered A
light coating of water is sprayed or wiped onto the surface of
the coal, and the rate at which it disappears is observed Rapid
disappearance (typically within a few seconds) indicates
ab-sorption and demonstrates that the coal contains less than its
full compliment of inherent moisture Slower disappearance
(taking perhaps a minute or more) is characteristic of
evapo-ration and suggests that the pores are filled with moisture To
account for variations in field conditions such as temperature,
humidity, different absorption rates by different coals, and so
forth, the test is applied to a number of coal pieces both before
and during the sample collection process
6.2 Sampling Plan for Classification According to Rank:
6.2.1 Refer to Section 7 of ClassificationD388for
informa-tion on the required number and locainforma-tion of samples
6.2.2 The channel size shall be at least 8 cm (3 in.) deep and
10 cm (4 in.) wide, and shall yield at least 3 kg (6 lb) of coal
for each foot of thickness of coal seam
6.2.3 All roof and floor rock, mineral partings more than 1
cm (3⁄8in.) thick, and mineralized lenses or concretions (such
as sulfur balls) more than 11⁄4cm (1⁄2in.) thick and 5 cm (2 in.)
wide shall be excluded from the sample
6.3 Sampling for Other Purposes—Variations in the purpose
of sampling and in conditions encountered in the field preclude the establishment of rigid procedures covering every sampling situation In each case, formulate a plan taking into account the mining operation, the purpose of the sampling, and the known characteristics of the coal seam Characteristics include lateral
or vertical variations in coal quality, occurrences of persistent mineral partings or concretions within the seam, and the extent
of oxidation or weathering of coal Take these considerations into account in planning sample site selection and whether lithotypes, partings, and layers above and below the seam should be described.4,5Also establish a method of preparing the coal face, and determining the size of sample
6.3.1 Obtain information for identification of suitable loca-tions for sampling Choose sites that will best satisfy the purpose of sampling
6.3.2 A channel at least 8 cm (3 in.) deep (into the face of the seam) and 10 cm (4 in.) wide yields a sufficient sample for most purposes The channel may be enlarged to minimize the effect of channel size variability when a coal characteristic of interest, such as ash content, varies greatly from layer to layer
in the seam, or when the coal breaks unevenly Also, the channel cross-section may be enlarged to obtain sufficient sample for tests requiring large amounts The size of channel for the required amount of coal may be estimated from the density of coal—approximately 1.3 g/cm3 (0.05 lb/in.3) For information on determining washability, see Test Method
D4371and the report by Wizzard.6 6.3.3 Practice with respect to weathering of the coal de-pends on a number of factors Some characteristics of coal, such as total sulfur content, do not change appreciably with weathering if the coal is not leached The forms of sulfur, the moisture-holding capacity, and oxygen content of high volatile
C bituminous and lower rank coals, and the rheological properties of coking coals do change with weathering Sam-pling to different depths and testing of such properties may be required to establish the depth at which unweathered coal can
be obtained
7 Sampling Procedures
7.1 At each sampling site, survey the condition of the coal face and the rock above the coal (if exposed)
N OTE3—Warning: Beware of danger from rock falling from the roof
of underground mines or from the highwall of surface mines Take down any loose blocks as a safety precaution and to prevent extraneous material from subsequently contaminating the sample.
7.2 With a miner’s pick, remove weathered coal from the face area to be sampled, to the depth (but at least 3 cm (1 in.)) required in the plan of sampling True up to the face to leave a straight surface normal to the bedding and free of extraneous matter
4 Schopf, J M., “ Field Description and Sampling of Coal Beds,” U.S Geological Survey Bulletin No 1111-B, 1960.
5Field Description of Coal ASTM, 1978, pp 3–33, 58–68, ASTM STP 661,
6 Wizzard, J T., “The Reliability of Using Channel Samples to Represent
Run-of-Mine Coal Washability,” DOE/PETC/TR-82/3.
Trang 37.3 Describe and record observations on the character of
layers in the coal seam (see TerminologyD121or Definitions
D2796) to the extent required by the sampling plan
7.4 Mark the sides of the channel with chalk and mark any
mineral partings or other parts of the seam that are to be
discarded
7.5 Clear and smooth the floor adjacent to the sample area
and spread a ground cloth on the floor with one edge at the coal
face
7.6 Cut away with a miner’s pick (or other tool) a channel
from top to bottom (or bottom to top) of the coal seam If a saw
is used at the sides of the channel, exercise care that fines
generated by the saw do not become part of the sample Ensure
that all material from the channel that is to be sampled
according to the plan of sampling falls on the ground cloth and
that any mineral matter to be discarded does not contaminate the coal sample Cut the channel to a uniform width and depth
in a rectangular cross section, to ensure that representative volumes of material are obtained from every part of the coal seam
7.7 As quickly as possible, if inherent moisture will be determined, transfer the material on the ground cloth to a sample container and seal and then label the container If surface moisture is visible on the coal, or if there is any reason
to question the accuracy of inherent moisture content deter-mined from the sample, the description of the sample shall include the warning: “Moisture content questionable.”
8 Keywords
8.1 channel; coal; mine; rank; sample collection; sampling
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org) Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222
Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/