tài liệu lab ccna

... confidently pass the CCNA exam. So, all the book features, which are outlined in the Introduction, are geared toward helping you discover what CCNA topics you do know well, what CCNA topics you ... 4:55 PM Recommended Training Path for CCNA 11 Recommended Training Path for CCNA Cisco recommends that you take two courses before you take the CCNA exam. The first, Internetworking Technology ... the CCNA Exam 4 Overview of Cisco Certifications 4 Exams Required for Certification 6 Other Cisco Certifications 7 What’s on the CCNA Exam 8 Topics on the Exam 9 Recommended Training Path for CCNA...

Ngày tải lên: 10/12/2013, 16:15

... 2 - 6 CCNA 4: WAN Technologies v 3.0 - Lab 1.1.4b Copyright  2003, Cisco Systems, Inc. • 2600 series routers Please refer to the chart at the end of the lab to correctly identify ... IOS command to represent the interface. 1 - 6 CCNA 4: WAN Technologies v 3.0 - Lab 1.1.4b Copyright  2003, Cisco Systems, Inc. Lab 1.1.4b Configuring NAT Objective • Configure ... session. Note: Refer to the erase and reload instructions at the end of this lab. Perform those steps on all routers in this lab assignment before continuing. Step 1 Configure the routers Configure...

Ngày tải lên: 11/12/2013, 13:15

... __________________________________________________________________________ 1 - 6 CCNA 1: Networking Basics v 3.0 - Lab 1.1.6 Copyright  2003, Cisco Systems, Inc. Lab 1.1.6 PC Network TCP/IP Configuration Objective ... This lab assumes the use of any version of Windows. This is a non-destructive lab and can be done on any machine without concern of changing the system configuration. Ideally, this lab is ... 3 - 6 CCNA 1: Networking Basics v 3.0 - Lab 1.1.6 Copyright  2003, Cisco Systems, Inc. Be sure to return to the adapter...

Ngày tải lên: 11/12/2013, 13:15

... 1 - 5 CCNA 1: Networking Basics v 3.0 - Lab 1.1.7 Copyright  2003, Cisco Systems, Inc. Lab 1.1.7 Using ping and tracert from a Workstation ... This lab assumes the use of any version of Windows. This is a non-destructive lab and can be done on any machine without concern of changing the system configuration. Ideally, this lab is ... computer recorded in the previous lab. The following figure shows the successful results of ping to this IP address. 5 - 5 CCNA 1: Networking Basics v 3.0 - Lab 1.1.7 Copyright  2003, Cisco...

Ngày tải lên: 11/12/2013, 13:15

... is ready for the assigned lab to be performed. 1 - 7 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 1.2.5 Copyright  2003, Cisco Systems, Inc. Lab 1.2.5 Verifying RIP v2 ... the chart at the end of the lab to correctly identify the interface identifiers to be used based on the equipment in the lab. The configuration output used in this lab is produced from 1721 series ... Establishing a HyperTerminal session lab. Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all routers in this lab assignment before continuing. Step...

Ngày tải lên: 11/12/2013, 13:15

... 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1.2.5 Copyright  2003, Cisco Systems, Inc. Step 1 Identify connectors and components a. Examine the router and locate the RJ-45 connector labeled ... 25-pin male connector labeled serial. It may or may not be identified. Step 3 Locate the RJ-45 to DB-9 adapter 1 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1.2.5 Copyright  ... Console or rollover cable for connecting the workstation to the router 3 - 4 CCNA 2: Routers and Routing Basics v 3.0 - Lab 1.2.5 Copyright  2003, Cisco Systems, Inc. Step 4 Locate or build a...

Ngày tải lên: 11/12/2013, 13:15

... 32 or 16, put 0s in row three of our table under the 32 and 16 values. 1 - 2 CCNA 1: Networking Basics v 3.0 - Lab 1.2.5 Copyright  2003, Cisco Systems, Inc. ... Lab 1.2.5 Decimal to Binary Conversion Objective • Learn to convert decimal values to binary...

Ngày tải lên: 11/12/2013, 13:15

Ngày tải lên: 11/12/2013, 13:15

Ngày tải lên: 11/12/2013, 13:15