learning autocad 2010 volume 1
Learning AutoCAD 2010, Volume 1 phần 4 docx
... with Units ■ 14 7 11 . For the next point: ■ Move the cursor to the left. ■ Enter 44'-5". Press TAB. ■ Enter 18 0. Press TAB. ■ Click anywhere in the drawing. 12 . Right-click ... symbol is typed. Example 16 ' -2" can be simply typed: 16 '2 ■ When using Architectural units, you may type 16 ' -2" or the equivalent in inches: 19 4 ■ If you work primarily ... understand the difference between 1 inch and 1 millimeter, there are some assumptions that can affect other settings such as Imperial Architectural units (for example1'-6"), and alternate...
Ngày tải lên: 09/08/2014, 11:20
Learning AutoCAD 2010, Volume 1 phần 5 pptx
... variable set to 1. 1. Begin by setting the MIRRTEXT system variable to 1. This turns the mirroring of text on. ■ At the Command line, enter MIRRTEXT and press ENTER. ■ Enter 1 and press ENTER. ... left corner as the basepoint. ■ Enter a rotation angle of 10 . Press ENTER. ■ Notice that the object is rotated 10 degrees counterclockwise. 18 4 ■ Chapter 3: Manipulating Objects 8. To ... Position the cursor so that the polar angle displays 18 0 degrees. Click to select that point. 10 . Close all files. Do not save. 214 ■ Chapter 3: Manipulating Objects Lesson: Creating...
Ngày tải lên: 09/08/2014, 11:20
Learning AutoCAD 2010, Volume 1 phần 6 doc
... 2 21 Practice Exercise: Creating an Array of Objects In this practice exercise, you draw a 1 x 1 rectangle and create an array using the Polar and Rectangular array options. 1. ... Introduction in Volume 1. Lesson: Creating Object Patterns ■ 219 Procedure: Creating a Polar Array of Objects The following steps are an overview of creating polar arrays. 1. On the ... Under Offset Distance and Direction, click Pick Both Offsets. Challenge Exercise: Grips ■ 2 41 11 . Use the Copy and Base Point grip modes to copy many objects at once to populate the next...
Ngày tải lên: 09/08/2014, 11:20
Learning AutoCAD 2010, Volume 1 phần 7 potx
... ESC to clear the selected line. 10 . Select a dimension in the drawing. The Quick Properties panel automatically displays two property rows. 11 . On the status bar, right-click ... 12 . In the Drafting Settings dialog box, Quick Properties tab, under Palette Behavior, clear the check mark for the Collapse Palette Automatically option. Click OK. 13 . ... drawing. The Quick Properties panel automatically expands. 14 . Press ESC to clear the selected dimension. 15 . Close all files. Do not save. Lesson: Changing Object Properties...
Ngày tải lên: 09/08/2014, 11:20
Learning AutoCAD 2010, Volume 1 phần 8 pot
... circles 2 and 3 = 10 3.9447 mm Distance between circles 2 and 4 = 10 5.6296 mm 11 . Angle = 13 1 degrees Delta Y = 44.9275 mm 13 . X = 253 .13 53Y = 0.0000Z = 0.0000 14 . Net area ... Distance = 55 mm Angle = 212 degrees 4. Radius for circle 2 = 17 .25 mm Radius for circle 4 = 10 .00 mm 5. Object type = LWPOLYLINE Area = 17 64.00 mmPerimeter = 318 .00 mm 9. Distance ... Volume Measures the volume of an object or a defined area. There are also options to keep a running total as you define volume or to subtract specified regions from total calculated volume. ...
Ngày tải lên: 09/08/2014, 11:20
Learning AutoCAD 2010, Volume 1 phần 9 pot
... Objects 10 . To remove the construction lines: ■ Start the Erase command. ■ Select the lines indicated in the following image. Press ENTER. 11 . Your completed drawing. 12 . ... (1) . ■ Select the object to join (2). ■ Press ENTER to complete the command. 5. To Join the arc segments and close them. Method 1: ■ Begin the Join command. ■ Select one arc (1) ... Press ENTER to exit the Offset command. 11 . Using the Trim command, clean up the hidden lines as shown in the following image. 12 . To create a hidden pocket in the front...
Ngày tải lên: 09/08/2014, 11:20
Learning AutoCAD 2010, Volume 1 phần 10 pot
... Objects 11 . To select a door to relocate within a wall: ■ Start the Stretch command. ■ Click near point (1) and then point (2) to define the crossing window. ■ Press ENTER. 12 . ... lengths at 1 for the same results. 3. To chamfer using the polyline option: ■ Draw another 8 x 6 rectangle (see #1) . ■ Begin the Chamfer command. ■ See that the current chamfer length is 1 and ... command from the drop-down menu. Menu Bar: Modify > Chamfer 412 ■ Chapter 5: Altering Objects 11 . To complete the right view: ■ Press ENTER to repeat the Fillet command. ■...
Ngày tải lên: 09/08/2014, 11:20