discovering vulnerabilities in control system humanmachine interface software
System Support for Software Fault Tolerance in Highly Available Database Management Systems
Ngày tải lên: 28/04/2014, 13:32
Shop Manual & ETM BCM KIA Cerato 2010 - Auto Lighting Control System
... controlled according to auto light sensor's input. The auto light control doesn't work if the pin sunlight supply (5V regulated power from Ignition 1 power to sunlight sensor) is in ... connector. Installation 1. Reconnect the auto light connector. 2. Install the auto light sensor. 2010 > G 1.6 DOHC > Body Electrical System Inspection In the state of IGN1 ON, when multi function switch ... Lighting switch (Auto) 4. Tail lamps 5. Body control module (BCM) 2010 > G 1.6 DOHC > Body Electrical System Circuit Diagram Language 2010 > G 1.6 DOHC > Body Electrical System ...
Ngày tải lên: 22/10/2012, 15:55
The research of using epad technology to support activities in administrative system
... Delete user R.4. New incoming document processing package R.4.1. Register into “incoming book” R.4.2. Store into database R.4.3. View new incoming documents R.4.4. Decide destination R.4.4.1. Public R.4.4.2. ... “incoming book” - General description Insert document’s information into “incoming book” form and store into database - References R.4.1 - Process description Action Response 1. Click on “incoming ... “incoming book” button 2. Show information form 5. Insert document’s information and click “Submit” 6. Store into database Exception Missing some fields in the form. Require fill in missing...
Ngày tải lên: 23/11/2012, 15:04
Vietnamese Speech Recognition and Synthesis in Embedded System Using T-Engine
... synthesis into our software running in T-Engine. This software allow users to use speech-commands to query information about places in Ha Noi. Figure 7 illustrate the main screen of the software, in ... quality of speech engines. Finally, we demonstrate a human-computer interaction software in T-Engine embedded system. I. INTRODUCTION In this paper, we are concerned with the combination of speech ... short introduction of T-Engine is given, while a method proposed for speech recognition in T-Engine is provided in Section 3, following is Vietnamese speech synthesis method in Section 4. In...
Ngày tải lên: 12/04/2013, 16:05
Điều khiển chạy tự động bằng điện tử Cruise Control System
... được giảm thiểu bằng chu kỳ đo đạt. Cả m biến tốc độ dẫn động cho Microcontroller’s Timer Input Capture Line hay Interrupt Line bên ngồi. Bộ ECU sẽ tính tốn tốc độ xe từ tần số của tín hiệu, bộ ... Actual Vehicle Speed Value Set speed value + Proportional gain, Kp - + Actuator Control Speed Sensor Intergral Gain, KI PGS. TS Đỗ Văn Dũng Hệ thống điện thân xe & điều khiền ... khiền tự động trên Ô tô Trang 242 CHƯƠNG 7: ĐIỀU KHIỂN CHẠY TỰ ĐỘNG BẰNG ĐIỆN TỬ CRUISE CONTROL SYSTEM (CCS) 7.1. KHÁI QUÁT VỀ HỆ THỐNG CHẠY TỰ ĐỘNG 7.1.1. Vai trò của hệ thống điều khiển...
Ngày tải lên: 09/11/2013, 03:15
Tài liệu An Introduction to Intelligent and Autonomous Control-Chapter 12: Learning in Control pdf
Ngày tải lên: 14/12/2013, 12:15
Digital control systems theory hardware software constantine h houpis gary b lamont
Ngày tải lên: 01/01/2014, 20:24
Tài liệu Mechatronics DC Motor / Tachometer Closed-Loop Speed Control System ppt
... Kevin Craig DC Motor / Tachometer Closed-Loop Speed Control System 4 4. Mathematical Model The steps in mathematical modeling are as follows: • Define System, System Boundary, System Inputs ... determine the performance of the final, closed-loop system. The experimental testing is performed in both the frequency domain and the time domain in order to determine the closed-loop system ... needed in feedforward control. It is evident, therefore, that the measurement subsystem is an important part of a control system. The measurement subsystem in a control system contains sensors...
Ngày tải lên: 25/01/2014, 13:20
Tài liệu Lecture Notes in Control and Information SciencesEditors: M. Thoma pdf
... characteristicinworking coordinate by using nonlinearcoordinate transform between the working coordinate andthe joint coordinate aboutarticulatedrobot arm. (2) Servo Controller of IndustrialMechatronic ... relevantdetail description is given in section 2.3.The discussedmodeling combining the modelingofthe whole servosystem in the former part, the importance of modelingcontrol system in future mechanis mmachinesisillustrated. 1.2.2Discussion ... When controlling arobot armwith this control pattern, the control system of an industrial robot arm, with eachlinear independentco- ordinate axis, is generallyapproximatedinworking coordinates....
Ngày tải lên: 13/02/2014, 08:20
Bạn có muốn tìm thêm với từ khóa: