cách vẽ hình chiếu thứ 3 trên autocad

... Scale Dimensions Text Multileaders Tables 2D Navigate 37 38x.book Page 13 Monday, June 25, 2007 11 :37 PM 14 CHAPTER 1 EXPLORING THE AUTOCAD AND AUTOCAD LT INTERFACE Take a moment to examine the top ... prompt Command window Coordinate readout Status bar 37 38x.book Page 7 Monday, June 25, 2007 11 :37 PM 8 CHAPTER 1 EXPLORING THE AUTOCAD AND AUTOCAD LT INTERFACE Below the Command window is the ... this chapter, see Chapter 21 for more information. 37 38x.book Page 9 Monday, June 25, 2007 11 :37 PM 10 CHAPTER 1 EXPLORING THE AUTOCAD AND AUTOCAD LT INTERFACE Here’s an exercise to let you

Ngày tải lên: 06/11/2013, 11:15

... Mastering AutoCAD ® 2008 and AutoCAD LT ® 2008 George Omura 37 38x.book Page iii Monday, June 25, 2007 11 :37 PM 37 38x.book Page ii Monday, June 25, 2007 11 :37 PM Mastering AutoCAD ® 2008 and AutoCAD ... 2008 37 38x.book Page i Monday, June 25, 2007 11 :37 PM 37 38x.book Page ii Monday, June 25, 2007 11 :37 PM Wiley Publishing, Inc. Mastering AutoCAD ® 2008 and AutoCAD LT ® 2008 George Omura 37 38x.book ... for choosing Mastering AutoCAD 2008 and AutoCAD LT 2008 xxxi 37 38x.book Page xxxii Monday, June 25, 2007 11 :37 PM 37 38x.book Page 1 Monday, June 25, 2007 11 :37 PM Part 1 The Basics

Ngày tải lên: 06/11/2013, 11:15

... complete the sink. 13. Save your drawing. It should look like Figure 4 -30 . 5 1 4 6 2 3 10_788864 ch04.qxp 5/22/06 7: 13 PM Page 91 92 Part I ✦ AutoCAD and AutoCAD LT Basics Figure 4 -30 : The completed ... drawing as ab04-08.dwg in your AutoCAD Bible folder. On the CD-ROM Note Tip 10_788864 ch04.qxp 5/22/06 7: 13 PM Page 93 94 Part I ✦ AutoCAD and AutoCAD LT Basics 3. Start the LINE command. 4. From ... 4 -32 . Figure 4 -32 : The completed steam boiler. Summary This chapter covered a great deal about specifying coordinates. These skills form the basis for all your future work with AutoCAD and AutoCAD

Ngày tải lên: 08/08/2014, 23:20

... command, type 'filter... is shown in Figure 1 0 -3 3 2 1 3 4 5 6 Figure 1 0 -3 3: A mechanical drawing showing a small section of a “porcupine” mixer 3 Choose Fillet from the Modify toolbar ... ch10.qxp 230 5/22/06 7: 23 PM Page 230 Part II ✦ Drawing in Two Dimensions The FILLET command defines the fillet arc by its radius, as shown in Figure 1 0 -3 2 Radius Fillet arc Figure 1 0 -3 2: ... like Figure 1 0 -3 4 231 17_788864 ch10.qxp 232 ... Right-click and choose Move from the shortcut menu At the Specify move point or [Base point/Copy/Undo/eXit]: prompt, type @0, 3 ↵ The model

Ngày tải lên: 08/08/2014, 23:20

... 13- 25 shows an example of a title block that uses fields. Figure 13- 25: Filling in a title block is easier when you use fields. Cross- Reference 20_788864 ch 13. qxp 5/22/06 7:16 PM Page 35 3 35 4 ... on), and objects (any object that you select). On the CD-ROM 20_788864 ch 13. qxp 5/22/06 7:16 PM Page 35 2 35 3 Chapter 13 ✦ Creating Text Other: Displays values of AutoLISP variables and system ... anywhere inside cell B3. At the Select second corner of table cell range: prompt, click anywhere inside cell B6. Press Enter. Your table should look like Figure 13- 23. Figure 13- 23: The plat acreage

Ngày tải lên: 08/08/2014, 23:20

... 5 2 6 3 4 Figure 1 7-1 3: The title block inserted into paper space 13 Click the right mouse button and then choose Repeat 1 Viewport At the prompt, choose 3 in Figure 1 7-1 3 At the ... tablet ↵ and on ↵. 6. Type line ↵. Note Note 23_ 788864 ch16.qxp 5/22/06 7:17 PM Page 4 83 484 Part II ✦ Drawing in Two Dimensions 7. In Figure16 -38 , pick 3 with the digitizer, then 4, and then each ... the... saved in AutoCAD 2000 /AutoCAD LT 2000 or later format Moreover, the template that you use to open a new drawing must be set to use named plot styles AutoCAD and AutoCAD LT come

Ngày tải lên: 08/08/2014, 23:20

... Tạo 2 bậc Tạo rãnh giữa Cho hai hình chiếu : - Vẽ hình chiếu thứ 3 - Dựng hình chiếu trục đo Tạo khối trụ R14, h10 Vẽ giao tuyến Dựng hình bao hình chiếu thứ 3 Dựng khối vật thể Tạo lổ R17 BỘ ... hiện : Nguyễn Quốc Duy Lớp : DHCK2TLT MSSV : 08274441 Bài tập : 5.51 Vẽ hình chiếu thứ 3 và hình chiếu trục đo từ 2 hình chiếu Tạo lỗ suốt R9 ...

Ngày tải lên: 29/06/2014, 07:50