2000 toyota camry repair manual pdf download

... sure to read the following item carefully, thenfollow the correct procedure described in the repair manual Trang 3Observe the sight glass on the liquid tube.Test conditions:
Running engine at ... detector and repair if neces- sary (2) Charge proper amount of frigerant re-(3) If indicated pressure value is near 0 when connected to gauge, create the vacuum after inspecting and repairing the ... Bubbles present in sight glass Insufficient* (1) Check for gas leakage with gas leak tector and repair if necessary de-(2) Add refrigerant until bubbles disappear 2 No bubbles present in sight

Ngày tải lên: 28/04/2014, 12:52

... strainer Torque: 10 N·m (100 kgf·cm, 7 ft·lbf) AND MANUAL VALVE BODY (a) Align the manual valve with the pin on the manual shaftlever (b) Lower the manual valve body into place (c) Temporarily install ... plate wear
Brass (non–magnetic): bushing wear AND MANUAL VALVE BODY (a) Remove the detent spring on the manual valve body.(b) Remove the manual valve body (a) Remove the 3 bolts and the oil ... speed sensor assembly and torque thebolts Torque: 16 N·m (160 kgf·cm, 12 ft·lbf) Trang 4ON–VEHICLE REPAIR(a) Remove the nut and control cable (b) Remove the nut, washer and control shaft lever CONNECTOR

Ngày tải lên: 28/04/2014, 12:53

... lock manual switch OFF or UNLOCK No continuity A16 – Ground Door lock manual switch LOCK Continuity A17 – Ground Door lock manual switch OFF or LOCK No continuity A17 – Ground Door lock manual ... Door lock manual switch OFF or UNLOCK No continuityA1 – Ground Door lock manual switch LOCK Continuity A2 – Ground Door lock manual switch OFF or LOCK No continuity A2 – Ground Door lock manual ... No.1) 5 Wire Harness ––– BE–70 – Door lock system does not operate by manual switch 1 Power Window Master Switch 2 Door Lock Manual Switch 3 Integration Relay (I/P J/B No.1) 4 Wire Harness BE–60BE–70BE–70

Ngày tải lên: 28/04/2014, 13:03

... engine coolant level should be between the ”LOW” and ”FULL” lines If low, check for leaks and add ”Toyota Long Life Coolant” or equivalent up to the ”FULL” line 2 CHECK ENGINE COOLANT QUALITY (a) ... fill the system with coolant
Use of improper coolants may damage engine ing system cool-
Use ”Toyota Long Life Coolant” or equivalent andmix it with plan water according to the manufactur-er’s ... be between the ”LOW” and ”FULL” lines, when the engine is cold If low, check for leaks and add ’’Toyota Long Life Coolant” or Equivalent up to the ”FULL” line 2 CHECK ENGINE COOLANT QUALITY (a)

Ngày tải lên: 28/04/2014, 13:10

... CONNECT TOYOTA HAND–HELD TESTER OR OBDII SCAN TOOL (a) Remove the fuse cover on the instrument panel (b) Connect a TOYOTA hand–held tester or OBDII scan tool to the DLC3 (c) Please refer to the TOYOTA ... CONNECT TOYOTA HAND–HELD TESTER OR OBDII SCAN TOOL (a) Remove the fuse cover on the instrument panel (b) Connect a TOYOTA hand–held tester or OBDII scan tool to the DLC3 (c) Please refer to the TOYOTA ... scan tool to the DLC3 (c) Please refer to the TOYOTA hand–held tester or OBDIIscan tool operator’s manual for further details 3 CONNECT TIMING LIGHT TO ENGINE 4 INSPECT IGNITION TIMING (a) Using

Ngày tải lên: 28/04/2014, 13:24

... for looseness or for missing nuts If necessary, tighten them 4 TIRE ROTATION Check the owner’s manual supplement in which the maintenance schedule is shown 5 WINDSHIELD WIPER BLADES Check for ... replace the ball joint 6 CHECK TRANSAXLE OIL (FLUID) If leakage is found, check for the cause and repair 7 REPLACE TRANSAXLE OIL (FLUID) Replace the transaxle oil S51: (See page MX–4) E153: (See

Ngày tải lên: 28/04/2014, 13:26

... thetransaxle to the engine
Temporarily tighten the transaxle mounting bolts Trang 9MX051–01 –MANUAL TRANSAXLE (E153) MANUAL TRANSAXLE UNIT MX–9 INSTALLATION Installation is in the reverse order of removal ... the output shaft right and left 2 or 3 times to allow thebearing to settle Trang 23– MANUAL TRANSAXLE (E153) MANUAL TRANSAXLE ASSEMBLY MX–23 (j) Using a torque wrench, measure the preload Preload

Ngày tải lên: 28/04/2014, 13:27

... clutch hubTrang 63PREPARATION MANUAL TRANSAXLE (E153) Trang 64PREPARATION MANUAL TRANSAXLE (E153) Trang 65PREPARATION MANUAL TRANSAXLE (E153) PP–65 117 LUBRICANT Manual transaxle oil (w/ Differential ... bearingouter race Trang 68PREPARATION MANUAL TRANSAXLE (S51) Trang 69PREPARATION MANUAL TRANSAXLE (S51) Trang 70PREPARATION MANUAL TRANSAXLE (S51) 122 LUBRICANT Manual transaxle oil (w/ Differential ... gauge Torque wrench Trang 58SST (Special Service Tools)Trang 59PP0HD–01–Trang 60PP0HE–01–Trang 61MANUAL TRANSAXLE (E153)SST (Special Service Tools) Bearing Cone Replacer Output shaft rear bearing

Ngày tải lên: 28/04/2014, 13:31

... sure to read the following items carefully, then follow the correct procedures described in the repair manual F Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most ... up power supply from outside the vehicle F Before repairs, remove the airbag sensor if shocks are likely to be applied to the sensor during repairs F Do not expose the steering wheel pad, front ... from another vehicle When replacing parts, replace them with new parts F Never disassemble and repair the steering wheel pad, front passenger airbag assembly, side airbag assembly, airbag sensor

Ngày tải lên: 28/04/2014, 13:32

... Select the active test mode on the TOYOTA hand–held tester (4) Please refer to the TOYOTA hand–held tester ator’s manual for further details oper-(5) If you have no TOYOTA hand–held tester, connectthe ... Select the ACTIVE TEST mode on the TOYOTA hand–held tester (d) Please refer to the TOYOTA hand–held tester operator’smanual for further details (e) If you have no TOYOTA hand–held tester, connect ... switch OFF (8) Disconnect the TOYOTA hand–held tester from theDLC3 Trang 6(a) Connect a TOYOTA hand–held tester to the DLC3.(b) Turn the ignition switch ON and push the TOYOTA hand–held tester main

Ngày tải lên: 28/04/2014, 13:35

... that there is no continuity tween the field coil end and field frame be-If there is continuity, repair or replace the field frame Using vernier calipers, measure the brush length Standard length: ... no continuity tween the positive (+) and negative (–) brush holders be-If there is continuity, repair or replace the brush holder (a) Check the gear teeth on the pinion gear, idler gear andclutch ... that there is no continuity tween the field coil end and field frame be-If there is continuity, repair or replace the field frame Using vernier calipers, measure the brush length Standard length:

Ngày tải lên: 28/04/2014, 13:35

... the priority of the likelycause of the problem Check each part in the order shown If necessary, repair or replace these parts Hard steering 1 Tires (Improperly inflated) 2 Power steering fluid ... PUMP Trang 20Pressure Port Union
Oil RingFlow Control Valve Suction Port Union
5S–FE Engine : TOYOTA KOUKI Made : 24 (240, 17) Trang 211 REMOVE FRONT FENDER APRON SEAL RHRemove the 2 bolts 2

Ngày tải lên: 28/04/2014, 13:38

... Painting Procedures Fundamental Body Repair Procedures Electrical Wiring Diagram (Ex USA and Canada) (USA and Canada) CAMRY Chassis and Body Repair Manual CAMRY Repair Manual (USA and Canada) 36438E ... specifications and repair procedures other than collision-damaged body components of the TOYOTA CAMRY, refer to the following repair manuals. All information contained in this manual is the most ... Trang 1Manual Name Pub No.1S, 1S-E, 2S, 2S-C, 2S-E, 3S-FE & 3S-GE Engine Repair Manual (Ex USA and Canada) 1C, 2C & 2C-T Engine Repair Manual (Ex USA and Canada) Fundamental

Ngày tải lên: 29/04/2014, 08:46

... than those listed in this manual, refer to the following manuals; Volume 2  TCCS (3S–FE) Diagnosis Manual  ECT (A140E) Diagnosis Manual  ECT (A540E) Diagnosis Manual  1990 Model New Car ... diagram manual has been prepared to provide information on the electrical system of the 1990 TOYOTA CAMRY. Applicable models: SV21, 25 series VZV21 series For service specifications and repair ... information in this manual is based on the latest product information at the time of publication However, specifications and procedures are subject to change without notice. TOYOTA MOTOR CORPORATION

Ngày tải lên: 29/04/2014, 08:54

... relay Unlock Operation Key Cylinder Trang 9– MEMO – Trang 1064 CAMRY—OUTLINE OF NEW FEATURESCAMRY OUTLINE OF NEW FEATURES The Toyota Camry is a compact class passenger car with a wealth of model ... model year to raise the Camry’s product appeal 1 3S–FE Engine Plastic region tightening is used for the cylinder head bolts for good axial tension Refer to the 1990 Camry RepairManual (Pub No RM151U) ... most up–to–date at the time of publication However, Toyota reserves the right to make changeswithout prior notice TOYOTA MOTOR CORPORATION
1989 TOYOTA MOTOR CORPORATION All rights reserved This

Ngày tải lên: 29/04/2014, 08:55

... included in this manual. For new features of the Tercel and for detailed service specifications and repair procedures of each 1991 model year vehicle, refer to the following manuals:  1991 Tercel ... manuals:  1991 Tercel New Car Features NCF071U  1991 model Repair Manuals }Refer to respective  1991 model Electrical Wiring Diagram Manuals reallocaetd Pub No. All information contained herein ... notice. TOYOTA MOTOR CORPORATION
1990 TOYOTA MOTOR CORPORATION All rights reserved This book may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor

Ngày tải lên: 29/04/2014, 09:05

... AC–33 AC–21 AC–23 AC–23 AC–39 AC–43 AC–45 to 47 AC–22 Repair as necessary Replace blower motor Check amplifier Clean evaporator fins or filters Repair as necessary Check or replace drive belt Check ... Replace fuse and check for short Check blower motor Check blower resistor Check blower switch Repair as necessary Magnetic clutch slipping Expansion valve faulty Excessive moisture in the system ... Check magnetic clutch Check expansion valve Evacuate and charge system Check sensor Check amplifier Repair as necessary Check condenser Check or replace drive belt Check compressor Check refrigerant

Ngày tải lên: 29/04/2014, 09:07

... performing repairoperations Example: 1 Apply protection tape to the body adjacent to the body partwhen removing and installing If anti–rust agents are damaged while repairing other parts, be sure to repair ... Example: 1 If body sealer, paint film or undercoat are damaged bypeeling, cracks, etc., be sure to repair each with an antirustagent 2 When prying off the body parts with a screwdriver or scrap-er, ... If a hinge or exterior body panel is loosened or removed, be sure to apply rust inhibitor after repairs – BODY General Information BO–2 Trang 3ADJUSTMENT OF HOOD LEFT/RIGHT DIRECTIONS Adjust the

Ngày tải lên: 29/04/2014, 09:43

... relay Check relay Repair as necessary Replace fuse and check for short Check flasher Check switch Repair as necessary Replace fuse and check short Check flasher Check switch Repair as necessary ... Wiper motor faulty Wiring or ground faulty Repair as necessary Replace motor Check switch Repair as necessary Check relay Check switch Check motor Repair as necessary If continuity is not as ... bulb Check switch –Repair as necessary Replace fuse and check for short Replace bulb Check switch Repair as necessary Replace fuse and check for short Replace bulb Check switch Repair as necessary

Ngày tải lên: 29/04/2014, 09:47

... Replace brake shoes Replace pads Repair leak Repair or replace master cylinder Bleed brake system Repair wheel cylinder Repair cylinder Repair brake cylinder Repair or replace adjuster Air in ... Replace brake shoes Replace pads Repair leak Repair or replace master cylinder Bleed brake system Repair wheel cylinder Repair cylinder Repair brake cylinder Repair or replace adjuster Air in ... brake Repair as necessary Adjust push rod Replace spring Repair as necessary Replace shoe Replace pad Repair as necessary Replace pads Replace drum or disc Replace spring Repair wheel cylinder Repair

Ngày tải lên: 29/04/2014, 09:55