Bộ đề thi chứng chỉ Solidworks CSWPA Sheet Metal dành cho các bạn có nhu cầu thi để lấy chứng chỉ Solidworks quốc tế. Bộ đề thi chứng chỉ Solidworks Sheet Metal,Bộ đề thi chứng chỉ Solidworks Sheet Metal,Bộ đề thi chứng chỉ Solidworks Sheet Metal,Bộ đề thi chứng chỉ Solidworks Sheet Metal.
Trang 1Certification Exam Set
Trang 2A = 193 mm
B = 190 mm
C = 74 mm
|- Measure the mass of the resulting Sheet Metal part.
What is the mass of the Sheet Metal part (grams)?
Trang 4A = 193 mm
B = 190 mm
C = 74 mm
-Measure the mass of the resulting Sheet Metal part.
What is the mass of the Sheet Metal part (grams)?
Enter Value:
(use (point) as decimal separator)
Trang 5Question 3 of 15
For 5 points:
A3002 - Flatten the part Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Part origin: Arbitrary Material = Aluminum Alloy, 1060 Alloy, Density = 0.0027 g/mm3 Sheet Metal Thickness: 1.50 mm Inner Bend Radius = 1.00 mm General K-Factor = 0.32
Trang 6|-Measure the mass of the resulting Sheet Metal part.
What is the mass of the Sheet Metal part (grams)?
51.50
Trang 7A = 200 mm, B = 200 mm, C = 70 mm
-Change the part's K-Factor to 0.48
-Measure the maximus measured extent (X) of the part when flattened (See layimage.)
Trang 8What is the maximum measured extent (X) of the part when flattened?
Trang 10(use (point) as decimal separator)
Trang 12-Flatten the part
Note: There should be no interference after the part is flattened V
Trang 13Question 8 of 15
For 10 points:
B1001 - Create Sheet Metal Part From Solid Part Unit system: IPS (inch, pound, second) Decimal places: 2 Part origin: Arbitrary Material = Already defined Sheet Metal Thickness: 0.125 inch Inner Bend Radius = 0.225 inch General K-Factor = 0.5
- Download the attached part.
NOTE: DO NOT modify any of the material properties of the part.
- Create a Sheet Metal part that will fit around the downloaded part using the following parameters:
Trang 14Attachment to this question
B.SLDPRT (153.5 kB)
Enter Value:
(use (point) as decimah separator)
Sheet Metal Thickness: 0.125 inch
Inner Radius: 0.225 inch
Keep Body = OFF
Gap For All Rips: 0.08 inch
Overlap Ratio :0.50
Obround Relief Ratio: 0.50
Note 1: The sheet metal part should be OUTSIDE of the
downloaded solid (Any small interferences between the sheet metal part and solid at the folded edges should be ignored.)
Note 2: The bottom of the sheet metal part is open The Jinside of the part shown in the images is colored for clarity Your part will probably differ in color.
|- Measure the mass of the resulting Sheet Metal part.
What is the mass of the Sheet Metal part (pounds)?
Trang 16- Using the Sheet Metal part created in the previous question, measure the Bounding Box Area of the flattened Sheet Metal part.
What is the Bounding Box Area of the flattened Sheet Metal part (inches)?
Trang 17- Create a hem on the Sheet Metal part using the following parameters:
Hem Type: Open Length: 1.00 inch Gap Distance: 0.125 inch Custom Relief Type: Rectangular Relief Ratio: 0.50
-Measure the mass of the Sheet Metal part.
What is the mass of the Sheet Metal part (pounds)?
Enter Value:
I
(use (point) as decimal separator)
Question 11 of 15
Trang 18For 10 points:
C1001 - Cutting Length - Outer Unit system: IPS (inch, pound, second) Decimal places: 2 Part origin: Arbitrary Material = Already defined Sheet Metal Thickness = Already defined Inner Bend Radius = Already defined General K-Factor = Already defined
- Download and open the attached part file.
NOTE: DO NOT modify any of the material properties of the part.
- Using the Sheet Metal Cut List, measure the Outer Cutting Length of the flat pattern.
Attachment to this question
Question 12 of 15
For 10 points:
Trang 19C2001 - Gauge Table Import Unit system: IPS (inch, pound, second) Decimal places: 2 Part origin: Arbitrary Material = Already defined Sheet Metal Thickness = Already defined Inner Bend Radius = Already defined General K-Factor = Already defined
- Download the attached Gauge Table.
- Using the downloaded Gauge Table, apply it to the sheet metal part downloaded in the previous question.
- Use the Gauge Table to apply the following parameters to the Sheet Metal part:
Attachment to this question
Trang 20- Using the applied Gauge Table from the previous question, modify the inner radius of the two bends circled in the image to the following value:
Inner Radius: 0.5 inches (Gauge Table Value)
- Measure the Bounding Box Length.
- What is the Bounding Box Length (inches)?
Enter Value:
(use (point) as decimal separator)
Question 14 of 15
For 10 points:
Trang 21D1001 - Louver Placement Unit system: MMGS (millimeter, gram, second) Decimal places: 2 Part origin: Already defined Material = Already defined Sheet Metal Thickness = Already defined Inner Bend Radius = Already defined General K-Factor
Trang 22|- Using the previously modified part, create a pattern of the louver using the following parameters:
Spacing = 30.00 mm Number of Instances = 5
-Measure the Center of Mass of the Sheet Metal part.
Trang 23What is the Center of Mass of the Sheet Metal part (mm)?