Council of Science and Technology, Bhopal, India a r t i c l e i n f o Article history: Received 5 February 2019 Received in revised form 28 July 2019 Accepted 10 August 2019 Available o
Trang 1Original Article
using low-energy positron lifetime measurements
a Vikram University, Ujjain, 456010, MP, India
b Lovely Professional University, Jalandhar, Punjab, India
c M.P Council of Science and Technology, Bhopal, India
a r t i c l e i n f o
Article history:
Received 5 February 2019
Received in revised form
28 July 2019
Accepted 10 August 2019
Available online xxx
Keywords:
Polystyrene thin films
ZnO
TiO 2
Positron annihilation
Free volume hole
Interfacial interaction
Solution cast method
a b s t r a c t
To reveal how the distribution of different nanofillers affect the UV-shielding efficiency of their polymer-based composites and to further develop a simple strategy to refrain the erection of the composites, we prepared ZnO doped polystyrene (PS/ZnO) and TiO2doped polystyrene (PS/TiO2)films by the solution cast technique with different concentrations of ZnO and TiO2(0.25%, 0.5%, 0.75% and 1%.) Contrary to the common observation, the better tunability for UV shielding efficiency was found in case of TiO2as compared to ZnO This is mainly due to the appearance of a rod like structure on neat PS which has improved the dispersion as well as provides a higher interface area that enhanced the UV-absorption
efficiency of the PS matrix This analysis is equally supported by the PALS study where the free vol-ume was closely associated with the interfacial interaction between thefiller and the PS matrix These observations recommend that the better dispersion offiller particles leads a stronger interfacial inter-action and enhances the UV-protection efficiency of the composite materials
© 2019 The Authors Publishing services by Elsevier B.V on behalf of Vietnam National University, Hanoi This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/)
1 Introduction
Previously, our group has successfully prepared TiO2/PSfilms
with concentrations up to 1 wt % by the solution cast method in the
development of photo-protective polymeric materials for the
pro-tection against ultraviolet radiation Interestingly, the as-prepared
thin films have shown a tremendous UV-shielding proficiency
[1,2] These results suggested to pursue a further study on the
re-lationships among the atomic free volume and the interfacial
interaction between thefiller particles and the PS matrix Contrary
to the common observations where numerous approaches have
been made for the development of ZnO doped composites as a
better UV protective material, in our previous study TiO2 has
expressed a better harmony for the efficient UV shielding which we
will incorporate in the present work as a comparative study To
analyze the imperfections produced at the early stage of the
process in engineering materials it is important to predict the weakness and failure of the material This work is consequential for the final understanding of the UV-shielding efficiency by comparing its results with those of a widely studied material as ZnO The very extensively studied inorganic materials ZnO and TiO2 with a wide band-gap energy of 3 eV have been expansively used as inorganic UV absorbers due to their significant optical properties [3] Consequently, such polymer nanocomposites have been regarded as excellent candidates for UV shielding applications As a matter of fact, the extraordinary properties of the polymer nano-composite include the dispersion of the nanoparticles in the matrix and the subsequent growth of enormous interfacial areas This complete dispersion allows the exploration of the available matrixeparticle interface and then the optimization of the organiceinorganic interaction which is accountable for the improved properties of thefinal material Nevertheless, there have been less reported on the research efforts in this area especially those dealing with the effect of the free volume hole and the interfacial interaction on the UV-shielding efficiency[4e6] More-over, most of the works have adopted higher dopant concentrations
to conquer a better UV-shielding efficiency of the films [4,7e10]
* Corresponding author Lovely Professional University, Jalandhar, Punjab, India.
E-mail addresses: acharyaphysics2011@gmail.com (A.D Acharya), sarbhawna@
gmail.com (B Sarwan).
Peer review under responsibility of Vietnam National University, Hanoi.
Contents lists available atScienceDirect Journal of Science: Advanced Materials and Devices
j o u r n a l h o m e p a g e : w w w e l s e v i e r c o m / l o c a t e / j s a m d
https://doi.org/10.1016/j.jsamd.2019.08.003
2468-2179/© 2019 The Authors Publishing services by Elsevier B.V on behalf of Vietnam National University, Hanoi This is an open access article under the CC BY license ( http://creativecommons.org/licenses/by/4.0/ ).
Trang 2the free volume properties of polymers in the amorphous state can
be accomplished by the use of the positron annihilation lifetime
spectroscopy technique (PALS) This technique involves the
inser-tion of positrons into the material and then recording the
indi-vidual positron lifetimes until the annihilation with electrons of the
sample takes place[11,12] Since the fraction of the positrons
an-nihilates from the state of an orthopositronium (o-Ps) and the
lifetime of the orthopositronium depends on the size of the free
volume cavity where it is placed, hence, it can be employed to
characterize the free volume size in amorphous polymers
Following the above described study concern, the main motivation
of the present work is to investigate what would be the effects of
doping ZnO and TiO2 into PS on the atomic free volume, the
interfacial contact among thefiller particles and the PS matrix, and
the UV-absorption efficiency of PS at low content of fillers by the
positron annihilation lifetime spectroscopy
2 Experimental procedure
ZnO/PS and TiO2/PS thinfilms with different concentrations viz
0.25%, 0.5%, 0.75% and 1% have been prepared by using the solution
casting method The polystyrene was procured from the market
which was in the granular form The PS solution was prepared in
the dichloromethane, the requisite amount of semiconductors (ZnO
or TiO2) was then added into the solution under rapid stirring for
uniform dissolution The resultant was then poured on to a cleaned
petri dish to cast thefilm and the solvent was subsequently allowed
to evaporate gradually over a period of 12e24 h in a dry
atmo-sphere The membrane was then physically peeled off from the
surface The area of the cast surface, the material quantity and the
density of the material can determine the thickness of the
mem-brane We have prepared the polymer thinfilms of ~50mm
thick-ness For preparing the doped PS thin films, the dopant
concentration was calculated from the following equation[1,13]
wpþ wf 100
where,wf and wp represent the weight of the dopant and the
polymer, respectively
X-ray diffraction patterns of ZnO/PS and TiO2/PS thinfilms were
recorded on an X-ray diffractometer (Bruker D8 ADVANCE) with
Cu-Karadiation having the wavelength of 1.5418Å in the range of
2q¼ 200- 700 Atomic force microscopy (AFM) measurements were
carried out on a digital instrument of Nanoscope E with the Si3N4
100mm cantilever and 0.58 N/m force constant The transmittance
of thefilms has been measured with a UV-Vis Spectrophotometer
(PerkinElmer Lambda 950) Measurements of the positron lifetime
in ZnO/PS and TiO2/PS thinfilms have been done by using the slow
e fast coincidence method
3.1 Structural and surface analysis The XRD patterns of the films are shown in Fig 1 As it is perceived from the XRD patterns the pure PSfilm (Fig 1a,b) shows
an amorphous polymeric structure and the diffraction peaks of PS
do not appearein the patterns The pattern of the PS thinfilms loaded with 0.5 wt% TiO2 and ZnO (Fig 1 a,b), however, shows diffraction peaks of low intensity suggesting improved crystalinity
of the PS At the higherfiller content, the peak positions of the 1 wt
% sample is slightly shifted towards lower diffraction angles The most likely reason for this shift is the interaction between thefiller particle and the polymer structure that leads to a rearrangement of the PS chains (SeeFig 1a and b (Inset)) The increased intensity of the reflections from the diffracted planes with the higher amount of filler loadings suggests that a slowering of the crystallization rate arrised due to the enclosure offiller particles It can be concluded that a suitable, but not excessive, amount of dopant is responsible for observed good dispersion of the inorganicfiller particles in the
PS matrix
To get a further insight, we extended our approach to another important analysis using the atomic force microscopy (AFM) of the doped polymer samples.Figs 2 and 3show the AFM images of thin sections of the ZnO/PS and TiO2/PS composite surfaces loaded with the dopant content of 0.25, 0.5, 0.75 and 1.0 wt % It can be observed from AFM images (Fig 2) of PS/ZnO that the grain size increases with the increase in the ZnO concentration upto 0.5 wt% (See Fig 2c) leading to the aggregation The addition of ZnO particles at about 0.75 wt % does not encourage the faster crystallization (See Fig 2d) In case of the 1.0 wt % sample (SeeFig 2e), the efficiency of ZnO for enhancing the matrix crystallization get reduced due to the high particle density and obstructed the development of crystalline sections This illustrates that the small amount of ZnO particles i.e 0.5 wt% located in the PS matrix corresponds to the primary par-ticles and the extent of the agglomeration was found to be quite negligible The PS matrix having 0.75 wt% and 1.0 wt% ZnO particles changed to large size aggregates where several primary ZnO nanocrystallites were gathered Furthermore, the entire morphology was deformed when 1.0 wt% ZnO was employed
By comparing the AFM images, an obvious difference can be seen between the neat PS and the TiO2/PSfilm.Fig 3a shows an AFM image of thin sections of the TiO2/PS thinfilm at the dopant content of 0.25 wt % It signifies that the TiO2particles were setup in the form of aggregates of slackly linked paramount particles showing areas which are homogeneously implanted in the PS matrix After addition of 0.5 wt% TiO2into the matrix some rods appeared (SeeFig 3c) on the surface of the neat PS presuming that the formation of these rods mainly depends on the growth and nucleation conditions Moreover, a fractal type of aggregation of TiO2particles has been observed inFig 3d, such situation may arise due to the high concentration of nucleates that were formed by
Trang 3adding the 0.75 wt%filler content Moreover, looking intoFig 3e,
the nucleates randomly agglomerate in the continuous phase and
cause the increase of the number of TiO2particles, thus, making the
interface area larger and the overlap of these led to opaquely
appearing TiO2/PSfilms[9,13] This area is notably higher than that
of the 0.5 wt% TiO2/PSfilms This observation suggests that the
0.75 wt% TiO2/PSfilms have large particle agglomerates, while the
0.5 wt % TiO2/PSfilms have an improved dispersion as well as a
higher interface area and therefore exhibit a higher UV- absorption
efficiency From this analysis, it may be inferred that to speed up the
matrix crystallization and for altering the synthesized
nano-structure morphology, a low concentration of dopant as such of
0.5 wt % is enough Herewith, the AFM results suggest that the inorganic semiconductor particles were well incorporated in the
PS, which consequently modify significantly the morphology of the
PSfilms
3.2 ZnO/PS and TiO2/PS UVevis shielding The transmittance characteristics of the pure PS, the ZnO/PS and TiO2/PSfilms are visualized inFig 4 It is found that almost 99% of the light was passed-on by the pure PS in the UVevis region of wavelengths from 300 to 700 nm As shown in Fig 4a, the maximum value of transmittance of the ZnO/PS films containing
Fig 1 X-ray diffraction patterns: (a) ZnO/PS and (b) TiO 2 /PS thin films.
Fig 2 AFM images of ZnO/PS film.
Trang 40.25 wt % ZnO was found as pretty as 95% By a careful
consider-ation, it can be seen that the continuous inclusion of ZnO induces a
systematic decline of the transmitted light, lowering the
trans-mittance The transparency is also dependent on the dispersion/
aggregation of the nanoparticles into the polymer matrix The
fractal distribution of discretely dispersed nanoparticles favors the
optical transparent intensity loss of the transmitted light because
the scattering abruptly rises with the particle size This causes a
significant drop in the transparency of the films[10,14] In line with
this, the gradual decrease in the visible-light transmission from 95
to 70% in thefilms containing 0.25e1 wt % ZnO was observed and
highlighted by the shaded area inFig 4a The thinfilms with 1 wt %
ZnO dopant shows a non-uniform distribution of the ZnO particles
within the polymer matrix This could be endorsed by the AFM
results (Fig 2) where no substantial ZnO agglomerations were
found The obtained experimental results provide a visual illus-tration to the UV-shielding effect in ZnO/PS When ZnO/PSfilm is irradiated with the incident radiation, the visible light perfectly passes through the material as ZnO particles are apparent for the wavelengths greater than 375 nm while the UV-spectrum is obstructed depending on the ZnO concentration For the reason that the ZnO nanoparticles build a physical obstacle that the UV light cannot cross since they act as a protective network When the dopant concentration is further increased, the scattering mean free path gets decreased Due to this reason, the light traveled strongly inside thefilm with increased obstacle leading to the reduction in UV-light transmission to 63% with 1 wt% ZnO concentration (see Fig 4a)
The UVeVis transmittance of the TiO2/PS film is plotted in Fig 4b High transparency in both the visible and UV region is
Fig 3 AFM images of TiO 2 /PS film.
Fig 4 The transmittance spectra: (a) ZnO/PS and (b) TiO 2 /PS films.
Trang 5observed in the pure PSfilm (seeFig 4b), which is not competent to
filter out the UV radiations, whereas the addition of TiO2content
leads to the increase in the UV shielding efficiency due to the empty
conduction band and the filled valence band However, the UV
blocking consequence is seen in thefilms with TiO2contents as low
as 0.25 wt%, while the high transparency in the visible range is
maintained The concentration of 0.5 wt % TiO2could be assumed as
the optimal one for the better UV shielding effect as evidenced by
the graphical situation in the region bellow 355 nm, where more
than 70% transparency is observed This evidences that the
intro-duction of TiO2particles into the PS matrix is compatible to
in-crease the UV protecting proficiency of the PS film in the region
from 300 to 355 nm The further increment of TiO2 (0.75 wt %)
results in the opaque appearance with the increased absorption in
both the visible and UV region In this state, the apparent nature of
the material as a UV filter is decreased This behavior can be
interpreted by the fact that the increased amount of TiO2enhances
the interface scattering causing the reduction in the transmittance
This reduction might be ascribed to the growing cluster size[6] In
addition, the cluster size of thefilm becomes more non-uniform,
and irregular with the increasing TiO2content up to 1 wt%
lead-ing to the reduction in the transmittance as it is confirmed on the
AFM images (Fig 3e) of the compositefilms Here, the shape of the
PS latex is almost demolished and then totally vanished because of
the interdiffusion process between the polymer chains From this
result, it might apparently be easy to load the interstices of the thin
PS template with a low concentration of dopant, but it is difficult to
fill the interstices at a higher concentration So, the dopant content
can be considered as a key parameter for the permeation of the PS
templates[15]
The band gap energies (Egvalues) of the ZnO/PS and TiO2/PS films could be estimated from a plot of (ahn)2vs the photon energy (hn) inFig 5a,b Band gap values of 3.00, 2.47 and 2.61 eV were obtained for the pure PS, ZnO/PS and TiO2/PSfilms, respectively (for the optimum content, i.e 0.5%) However, two different mecha-nisms are accounted for the variation in the calculated optical band including: (1) The inclusion of a tiny amount of dopant produces charge transfer complexes in the host matrix which accelerate the electrical conductivity by providing additional charges which cause the reduction of the band gap [18,19]; (2) When the amount of dopants increases, the dopant molecules initiate to linking the gap between the localized states and thus lowering the potential bar-rier between them[16e22]
3.3 Positron annihilation lifetime studies The measurement for the positron annihilation lifetime studies (PALS) was carried out to examine the effect of TiO2and ZnO on the microstructure of the compositefilms The positron lifetime spectra
of the pure PS,ZnO/PS and TiO2/PSfilms, respectively, are presented
inFig 6 They show a systematic decreasing trend of the lifetime This indicates a decrease in the longest lifetime
The free volume size (Vf), and the o-Ps lifetime (t3) as a function
of the TiO2and ZnO content are shown inFig 7aeb, respectively FromFig 7a, it can be observed that the t3and Vfinitially drop with the TiO2 incorporation upto 0.5 wt% In the range from 0.5 to 0.75 wt%, a slight increase in t3and Vfis seen Theyfinally decrease
to the lowest value at higher doping, i.e at 1 wt% Looking again into Fig 7a, there is a decrease in t3and Vfwith the increasing TiO2 concentration (0.25e0.5 wt %) indicating that the additional
Fig 5 Plots of (a∙h∙y) 2 v/s photon energy (h ∙y): (a) ZnO/PSand (b) TiO 2 /PS thin films.
Fig 6 Positron lifetime spectra: (a) ZnO/PSand (b) TiO 2 /PS thin films.
Trang 6amount of TiO2 slows down the o-Ps formation This can be
explained by the fact thatfirstly the TiO2particlesfill up some of
the free volume holes in the PS and so the values of t3 and Vf
decrease Secondly, positrons may be annihilated from the TiO2
filler and there may be a lack of positrons which should be available
to form the positronium in PS[12] On the other side, the increase of
o-Ps at the dopant concentration of 0.75 wt% TiO2 suggests the
formation of new positron trapping sites at the TiO2ePS interface
As thefiller concentration is increased to that corresponding to the
1 wt% concentration, the TiO2filler inhibits the o-Ps formation and
thefiller particles are scattered among the molecular chains of the
PS and thus reducing the free volumes size leading to the decrease
of the o-Ps lifetime in the PS Quite the reversal, a small but
sys-tematic increase in the free volume size and in the o-Ps lifetime has
also been initially observed in the case of the low ZnO doping (i.e
0.25e0.5 wt%) (seeFig 7b) This is because of the development of
new positron trapping sites at the ZnO/PS interface The highest
values of t3and Vfhave been found for the 0.5 wt% ZnO/PSfilm,
whereas when we have increased the ZnO concentration upto 1 wt
%, the values of t3and Vfdecrease showing that some of the free
volume holes in the PS are filled up by the ZnO particles It is
interesting to note that the interfacial interaction between thefiller
and the polymer matrix has caused a vital effect on the free volume
size and the o-Ps lifetime This interaction dominates the delivery
of phonons between the matrix and thefillers[23e25]mainly at
0.5 wt% ZnO concentration where both the free volume size and the
o-Ps lifetime reach their maximum We recall the main fact that the
film with a low dopant amount ZnO represents a high surface area,
thus, providing more positron trapping sites which scatter the
phonons at the interface[26e28] However, at the high ZnO
con-centrations, the ZnO agglomerates and due to this interfacial
interaction, the induced disruption effect becomes limited,
reducing the free volume size and the o-Ps lifetime
3.4 The correlation of PALS results and UV-shielding
From the calculated results of the PALS and the morphological
studies, the UV-shielding efficiency of the ZnO/PS and TiO2/PSfilms
could be clearly understood From the PALS results of TiO2/PS, it is
noticed that the free volume hole size and the o-Ps lifetime initially
drop with the TiO2incorporation It might be an evidence for the
gradual formation of neutral aggregates at the initial level offiller
concentrations which creates blockages and reduces the free
vol-ume holes, enhances the crystallization of the matrix as it was
clearly confirmed by the AFM results This decrease in the free
volume holes may also contribute to the increase in the UV
shielding effect Furthermore, this factor reduces the ion and the
segmental mobility through the unified matrix and hence, leads to
the reduction of the free volume size At the high filler
concentrations, a random distribution of filler particles might initiate the formation of free volume holes in the PS matrix This process of the free volume formation gradually dominates the creation of neutral aggregates which fairly agrees with the AFM results and confirms the transition from the crystalline state to the amorphous one at higher TiO2concentrations where the regretable interaction between the loaded TiO2particles and the PS matrix have slight limitations on the segmental mobility because of less contact area and so contributing to the increase in t3 and Vf as shown inFig 7a An explanation based on the PALS results and detailed literature survey [27e29] implies that the o-Ps mainly annihilates in the interfacial regions In fact, there is some infor-mation indicating that the interfacial free volume is a vital factor for determinating the variation in the o-Ps annihilating lifetime because the interfaces have an excellent electronic density compared to the bulk phase
It is worth noting that in the case of ZnO/PS, the initial incre-ment in t3with increasing ZnO concentration upto 0.5 wt% (see Fig 7b) suggests the formation of the free volume and amorphous phases in the blend matrix due to the sufficient separation be-tween thefiller particles at low filler concentrations Our tentative elucidation is that the dispersion of ZnO particles can cause the disorder of the molecular configuration leading to the morpho-logical change in chains and thus increase in the free volume concentration and the o-Ps lifetime The above discussion cor-roborates that the better the dispersion of the lifetime the stronger will be the distraction of the molecular morphology On the other hand, as the ZnO content further increases, this distraction of ZnO weakens as being caused by the aggregation of ZnO leads to the decrease in the free volume concentration and the o-Ps lifetime The analysis also confirms that the free volume hole decreases with the increasedfiller concentration, because the filler limits the moving space of the molecular chains
From the above explanation it can be clear that the calculated free volume hole size does not show a drastic variation with the ZnO content, but revealing a very little amount being adequate to accelerate the matrix crystallization which assures a less tunability for the UV radiation This could be probable because an excessive amount of ZnO can obstruct the formation of well crystallized re-gions and lead to the turbidity/translucency of the composite ma-terials This illustrates that the particle size of the ZnO in the PS matrix corresponds to that of the primary particles and the extent
of the agglomeration is moderately negligible, whereas in the case
of TiO2particles the reduction in the free volume hole size leads to the increase in the UV shielding effect It is evident that the more exposure of the PS to the UV causes the increase in the size of the free volume hole while the hole density remains unchanged The destruction of the PS matrix sets in when TiO2is added leading to the formation of voids in the region of the TiO2particles aggregates
Trang 7This is attributed to the desorption and dispersion of the active
oxygen species produced on TiO2 surface engraving the polymer
matrix Furthermore, the rod shaped aggregation of the TiO2
nanoparticles (as shown inFig 3c) acting as the nucleating agents
leads to the increase in the UV shielding Moreover, doping with
TiO2results in a considerable increase in grain size due to the rod
shape aggregation that leads to the reduction of the grain boundary
scattering and this enhances the UV absorption and increases the
visible transparency of thefilms
To the best of our knowledge, the correlation between the
UV-absorption behavior and the free volume hole was for the first
time scrutinized Our experimental results clearly show that the
PALS are useful to understand the UV-absorption efficiency of
doped polymerfilm mixtures
4 Conclusions
The present research has explored the potential enhancement of
polymer's UV-shielding properties The attention of our study has
been focused on: (i) the analysis of properties of the atomic free
volume defect, (ii) thefiller-PS interfacial interaction and (iii) its
impact on the UV-protecting adequacy of thefilms which have
been investigated and examined by PALS Concussively, the shrink
of free volume hole size due to the highfiller concentrations is a
supporting positron lifetime parameter The calculated value for
the free volume hole size does not show any dramatic disparity
with the high ZnO concentrations revealing the less tunability of
the material for the UV radiation In the case of the TiO2particles,
however, the decrease in the free volume hole size has been
observed because of the rod shaped aggregation of the TiO2
parti-cles which act as nucleating agents contributing to the UV shielding
efficiency of the PS The results as obtained suggest that TiO2and
ZnO acting as activefillers for PS can be used for improving the
tremendous photo-protective shielding quality of the polymeric
materials to be applied in ultraviolet radiation protection Howbeit,
due to the surface free energy of the nanocrystals, ZnO particles
tend to aggregate making them obscured to attain a homogeneous
dispersal and that results in opaque compositefilms Therefore, the
main efforts should be focused on the nanocrystals without
ag-gregation in the PS
Acknowledgement
The authors are grateful to Dr Y.K Vijay (Prof.) at University of
Rajasthan, Jaipur for providing the experimental facilities to study
the positron lifetime and Dr Balram Tripathi for helping in the
analysis of the experimental data The authors also thank the
anonymous reviewers for their extremely insightful comments We
would like to convey our excellent gratitude to Prof Nguyen The
Hien Vietnam National University, Hanoi, Vietnam for the language
editing and formatting of the article Thefinancial support from
MPCST Bhopal is gratefully acknowledged
References
[1] A.D Acharya, Positron annihilation characterization of TiO 2 doped
poly-styrene, Mater Sci Forum 771 (2014) 169e177
[2] A.D Acharya, B Sarwan, R Sharma, S Moghe, S.B Shrivastava, V Ganesan,
UV-shielding efficiency of TiO2-polystyrene thin films prepared by solution
cast method, J Phys Conf Ser 836 (2017) 012048
[3] A.D Acharya, S Moghe, R Panda, S.B Shrivastava, M Gangrade, T Shripathi,
D.M Phase, V Ganesan, Effect of Cd dopant on electrical and optical properties
of ZnO thin films prepared by spray pyrolysis route, Thin Solid Films 525
(2012) 49e55
[4] V.S Sangawar, M.C Golchha, Evolution of the optical properties of Polystyrene thin films filled with Zinc Oxide nanoparticles, I.J.S.E Res 4 (2013) 2700e2705
[5] W Zhou, J Wang, Z Gong, J Gong, N Qi, B Wang, Investigation of interfacial interaction and structural transition for epoxy/nanotube composites by positron annihilation lifetime spectroscopy, Appl Phys Lett 94 (2009)
021904 [6] S Sharma, J Prakash, K Sudarshan, P Maheshwari, D Sathiyamoorthy,
P Pujari, Effect of interfacial interaction on free volumes in phenolformalde-hyde resine carbon nanotube composites: positron annihilation lifetime and age momentum correlation studies, Phys Chem Chem Phys 14 (2012) 10972e10978
[7] C Pirlot, I Willems, A Fonseca, J.B Nagy, J Delhalle, Preparation and char-acterization of carbon nanotube/polyacrylonitrile composites, Adv Eng Mater 4 (2002) 109
[8] Y Wang, T Li, P Ma, H Bai, Y Xie, M Chen, W Dong, Simultaneous en-hancements of UV-shielding properties and photostability of poly(vinyl alcohol) via incorporation of sepia eumelanin, ACS Sustain Chem Eng 4 (2016) 2252e2258
[9] X Meng, Z Zhang, N Luo, S Cao, M Yang, Transparent poly(methyl meth-acrylate)/TiO 2 nanocomposites for UV shielding applications, Polym Sci A 53 (2011) 977e983
[10] E Lizundia, L.R Rubio, J.L Vilas, L.M Leon, Poly(L-lactide)/ZnO nano-composites as efficient UV-shielding coatings for packaging applications, Appl Polym 133 (2016) 1e7
[11] L Khounlavong, V Ganesan, Influence of interfacial layers upon the barrier properties of polymer nanocomposites, J Chem Phys 130 (2009) 104901 [12] J Algersa, R Suzukib, T Ohdairab, F.H.J Maurer, Characterization of free volume and density gradients of polystyrene surfaces by low-energy positron lifetime measurements, Polymer 45 (2004) 4533e4539
[13] B Scrosati, B.V.R Chowdari, S Radhakrishna, Solid States Ionic Devices, World Scientific Publishing Co, 1988
[14] H Althues, J Henle, S Kaskel, Functional inorganic nanofillers for transparent polymers, Chem Soc Rev 36 (2007) 1454
[15] M Selin Sunay, O Pekcan, S Ugur, The effect of film thickness and TiO 2
content on film formation from PS/TiO 2 nanocomposites prepared by dip-coating method, J Nanomater (2012) 1e17
[16] J Rozra, I Saini, A Sharma, N Chandak, S Aggarwal, R Dhiman, P.K Sharma,
Cu nanoparticles induced structural, optical and electrical modification in PVA, Mater Chem Phys 134 (2012) 1121e1126
[17] C.U Devi, A.K Sharma, V.V.R.N Rao, Electrical and optical properties of pure and silver nitrate-doped polyvinyl alcohol films, Mater Lett 56 (2002) 167e174
[18] G Fussell, J Thomas, J Scanlon, A Lowman, M Marcolongo, The effect of protein-free versus protein-containing medium on the mechanical properties and uptake of ions of PVA/PVP hydrogels, J Bio Sci 16 (2005) 489e503 [19] A Nimrodh Ananth, S Umapathy, On the optical and thermal properties of in situ/ex situ reduced Ag NP's/PVA composites and its role as a simple SPR-based protein sensor, Appl Nanosci 1 (2011) 87e96
[20] A.J Marzocca, S Cerveny, W Salgueiro, A Somoza, L Gonzalez, Character-ization of free volume during vulcanCharacter-ization of styrene butadiene rubber by means of positron annihilation lifetime spectroscopy and dynamic mechanical test, Phys Rev 65 (2002) 021801
[21] R Gulotty, M Castellino, P Jagdale, A Tagliaferro, A.A Balandin, Effects of functionalization on thermal properties of single-wall and multi-wall carbon nanotube polymer nanocomposites, ACS Nano 7 (2013) 5114e5121 [22] D Konatham, A Striolo, Thermal boundary resistance at the graphene-oil interface, Appl Phys Lett 95 (2009) 163105
[23] C Liu, S Fan, Effects of chemical modifications on the thermal conductivity of carbon nanotube composites, Appl Phys Lett 86 (2005) 123106
[24] G Xue, J Zhong, S Gao, B Wang, Correlation between the free volume and thermal conductivity of porous poly(vinyl alcohol)/reduced graphene oxide composites studied by positron spectroscopy, Carbon 96 (2016) 871e878 [25] F.H Gojny, M.H.G Wichmann, B Fiedler, I.A Kinloch, W Bauhofer, A.H Windle, Evaluation and identification of electrical and thermal conduc-tion mechanisms in carbon nanotube/epoxy composites, Polymer 47 (2006) 2036e2045
[26] H Im, J Kim, Thermal conductivity of a graphene oxide carbon nanotube hybrid/epoxy composite, Carbon 50 (2012) 5429e5440
[27] U Rana, P.M Nambissan, S Malik, K Chakrabarti, Effects of process parame-ters on the defects in graphene oxide-polyaniline composites investigated by positron annihilation spectroscopy, Phys Chem Chem Phys 16 (2014) 3292e3298
[28] Y Li, S Wang, H Wu, R Guo, Y Liu, Z Jiang, Z Tian, P Zhang, X Cao, B Wang, High-performance composite membrane with enriched CO 2 -philic groups and improved adhesion at the interface, ACS Appl Mater Interfaces 6 (9) (2014) 6654e6663
[29] C Ohrt, K Ratzke, N Oshima, Y Kobayashi, B.E O'Rourke, R Suzuki,
A Uedono, F Faupe, Free volume profiles at polymer solid interfaces probed
by focused slow positron beam, Macromolecules 48 (5) (2015) 1493e1498