HƯỚNG DẪN LẬP TRÌNH THIẾT KẾ MÀN HÌNH HMI GOT1000 

(2) Computer link connection (serial communication module mounted on remote I/O station of MELSECNET/H network system) ( This section Computer link connection (serial communication [r]

GT Designer2

Version 2

(For GOT1000 Series)

SAFETY PRECAUTIONS

(Be sure to read these instructions before using the product)

Before using this product, read this manual and the relevant manuals introduced in this manual carefully and handle the product correctly with full attention to safety

Note that these precautions apply only to this product

In this manual, the safety instructions are ranked as "WARNING" and "CAUTION"

Note that failure to observe the CAUTION level instructions may also lead to serious results

depending on the circumstances

Be sure to observe the instructions of both levels to ensure personal safety

Please keep this manual in accessible place and be sure to forward it to the end user

[TEST OPERATION PRECAUTIONS]

WARNING

When testing the operation (e.g turning bit devices ON/OFF or changing a current word device value, a current or set timer/counter value, or a current buffer memory value), thoroughly read the relevant manual to fully understand the operating procedures When testing, never change the data

of the devices that control the operation essential for the system

Faulty output and malfunction may result in an accident

resulting in death or severe injury

resulting in medium or slight personal injury or physical damage

2 Free capacity of hard disk (virtual memory)

At least 100M bytes of free capacity of virtual memory should be secured within hard disk to run this software.The processing may be terminated by Windows , if 100M bytes or more of free space cannot be secured within hard disk while running GT Designer2

Secure enough free capacity of virtual memory within hard disk space in order to run the software

When enough free capacity cannot be secured, make sure to save projects frequently

3 Error messages displayed while starting and editing

"Operation will be terminated because of insufficient memory Would you like to stop?"

If the above message appears, close other running application software or reboot Windows in order to secure at least 50M bytes of free hard disk space

4 GT Designer2 and GOT display

(a) Cautions for displaying straight line other than full line (dotted line, for example) in bold

When straight line other than full line is drawn in bold, the line may not be displayed with its actual line width on a personal computer However, it will be displayed correctly on GOT This phenomenon does not mean data problem

(b) Display of end points of straight line/line freeform/polygon

As shown below, the end points of straight line/line freeform/polygon are displayed differently between

GT Designer2 and GOT

(c) Start position for filling patterns

Some filling patterns may be differently displayed For example, the start position may be different between GT Designer2 and GOT

(d) Drawing of different type lines

The length of the dots varies in different dotted lines (for example: the chain lines)

(e) Display of object

The display position of the memory data display in graph function is different between GT

Designer2 and GOT

Even if the display-start-line of a comment has been set, the comment will be displayed from the first line on GT Designer2

The color palette for setting color will be changed according to the new settings.

The color on the drawing screen will be kept the same as prior to the change

If the color setting for a [red] rectangle-figure is changed to the 2 colors (B/W), the [red] color will remain

The colors of the image data (BMP format file) will be reduced when the project is stored, the screen is closed and that image data is double-clicked

6 Object function and device type

The object (bit lamp or word lamp),for which bit device setting and word device setting are separated, cannot be converted between bit device and word device

7 When device type is changed

Confirm the device type when the set bit device is changed from bit device into word device

The device flag may be represented as "??", depending on the settings

Example: D0 b0 D0 D0.b5 ??

8 OS setting

Set the font size as "Small Font" when setting OS (Windows ) screen

The GT designer2 dialog box cannot be displayed correctly if the font size is set as "Large font"

9 When the toolbar icon appears in smaller size after startup of GT Desinger2

The toolbar icon may appear in smaller size right after GT Designer2 is started up

To correctly display the icon, initialize it as instructed below

that tab.)

10 When using GT Designer2 in the PC in which the OS other than applicable language version

The text may not be displayed correctly depending on the OS versions; some version include the fonts incompatible with GT Designer2 or GOT

Position of Paint mark may be shifted and the filled-paint may exceed the outline of the figure.

Reset All

A - 4

REVISIONS

* The manual number is given on the left bottom of the back cover

(Continued to next page)

How to Use This Manual, Chapter 1, Section 3.1, 3.8, 4.1.3, 5.1, 7.3.5, 8.2.2, 8.2.5, 8.3.5, 8.6.5, 8.8.5, 9.1, 9.2, 15.7.2

Function Quick Reference, Section 2.2, 2.3, 2.3.2, 2.4, 2.5.3, 2.8.1,2.8.2, 3.3.1, 3.6, 3.6.1, 3.7, 4.4, 4.4.1, 4.4.3, 5.1.3, 6.1.3, 6.1.4, 6.2.3, 6.2.5, 8.2.5 , 8.3.2, 8.4.7, 8.6, 8.6.6, 8.8, 8.8.4, 8.8.6, 9.1.1, 10.1.4

Section 3.10, 4.3, 9.1.2, 9.2.1, 9.2.2, Chapter 12, Section 13.2, 14.2, 14.3, 14.4, 14.5, 14.6, Appendix 4

Section 3.2, 12.1, 12.2.3

SAFETY PRECAUTIONS, HOW TO USE THIS MANUAL, Chapter 1, Section 2.7.3, Section 3.1, 3.2.2, 3.4, Section 5.2, Section 6.2.6, 6.2.10, Section 8.2.2, 8.2.6, 8.7.5, Section 12.3.5, Section 13.1.3, 13.1.

FUNCTION QUICK REFERENCE, Section 2.1.1, 2.1.2, 2.2, 2.3, 2.3.1, 2.3.2, 2.4, 2.5, 2.5.1, 2.5.3, Section 2.6.1, Section 2.7.1, 2.7.2, Section 2.8.1, 2.8.2, Section 3.1.1 to 3.1.3, 3.3.4, 3.3.5, 3.4.3, 3.5, 3.5.2, 3.6, 3.6.1, 3.6.4, 3.7.2, 3.7.3, 3.8.2, 3.9, Section 4.1.1 to 4.1.12, 4.3, 4.3.1, 4.4.1, 4.5.5, Section 5.1.2, 5.1.3, 5.3.1, 5.3.3, 5.5, 5.6, 6.1.3, 6.1.4, 6.2.3 to 6.2.5, 6.2.9, Section 7.1.3 to 7.1.5, 7.3.1, 7.3.4, 7.3.6, 7.4.3, 7.5.3, 7.5.4, Section 8.2.5, 8.3.6, 8.8.4, Section 9.1.4, 9.1.5, 9.1.7, 9.2.5 to 9.2.7, Section 10.1.4, 10.2.4, 10.3, 10.3.4, 10.4.4, 10.5.4, 10.6.4, 10.7.4, Section 12.2.3, 12.3.4, Appendix1, Appendix5

Section 2.8, 2.11, Section 3.11, Section 7.3.5, Section 10.8, Section 11.3, Section 14.4, 14.5, 14.6, 14.7, 14.8, 14.9, Appendix4

* The manual number is given on the left bottom of the back cover.

HOW TO USE THIS MAMUAL, Section 2.3, 2.3.3, 2.8.4, 2.8.6, 2.9.2, 2.10, Section 3.2.1 to 3.2.3,3.4.1 to 3.4.3, 3.5.2, 3.6.2 to 3.6.4, 3.7.1, 3.8.1, 3.10.1 to 3.10.3, Section 4.1.1, 4.1.3, 4.1.8, 4.1.12, 4.4, 4.4.7, 4.5.3, 4.5.5, Section 5.8.1,Section 8.2.2, 8.3.3, 8.5.3, 8.6.4, 8.8.2, Section 12.2.4, Section 13.3.2, 13.3.5, Section 15.1.3,Section 16.2.8, 16.3.4, 16.3.6

FUNCTION QUICK REFERENCE, MANUALS, ABBREVIATIONS AND GENERIC TERMS, Section 1.1, Section 2.1, 2.2, 2.3.1, 2.3.2, 2.4, 2.5, 2.7.1 to 2.7.3, 2.8, 2.9.1, 2.11, Section 3.1 to 3.10, Section 4.1 to 4.3, 4.4.3 to 4.4.5, 4.5.2, Section 5.1 to 5.8, Section 6.1, 6.2, Section 7.1 to 7.5, Section 8.1.1, 8.1.2, 8.2 to 8.8, Section 9.1 9.2, Section 10.1 to 10.8, Section 11.1 to 11.3, Section 12.1 to 12.3, Section 13.2, 13.3, Section 14.1 to 14.9, Section 15.1 to 15.3, Section 16.1.1, 16.2, 16.3, Appendix 1.4

Section 2.12, Section 3.12, 3.13, Section 4.4.1, 4.4.2, 4.4.6, Section 13.1

Section 1.1, Section 2.3.1, Section 3.1.3, Section 13.2.3, Section 16.4.3

Section 2.1.1, 2.1.2, 2.1.3, 2.4, 2.5, 2.5.3, 2.7.1, 2.7.2, 2.7.3,2.8.1, 2.8.3,2.8.4,2.8.5, 2.8.6, 2.8.8, 2.9.1, 2.9.2, 2.12, Section 3.1.2, 3.3.1, 3.3.4, 3.3.5, 3.6, 3.6.1, 3.6.4, 3.7.2, 3.7.3, Section 4.3, 4.3.1, 4.4.1, Section 5.1.3, 5.3.1, 5.3.2, Section 6.1.3, 6.1.4, 6.1.5, 6.2, 6.2.2, 6.2.3, 6.2.4, 6.2.5, 6.2.6, 6.2.7, 6.2.8, Section 7.1.3, 7.1.4, 7.2.4, 7.3.4, 7.3.5, 7.4.3, 7.5.3, 7.5.4, 7.5.5, Section 8.2.5, 8.3.5, 8.4.5, 8.4.7, 8.5.6, 8.6.4, 8.7.4, 8.8.4, Section 9.1.4, 9.1.5, 9.1.6, 9.2.5, 9.2.6, 9.2.7, Section 10.1.4, 10.2.4, 10.3.4, 10.4.4, 10.4.5, 10.5.5, 10.6.4, 10.6.5, 10.7.4, 10.7.5, 10.8.4, Section 11.3.4, Section 12.2.3, 12.3.4, Section 13.1.6, 13.3, Section 14.2, 14.5, 14.9, Section 15.1, Section 16.2.8, 16.3.8, Appendix 1, 4

Section 2.8.2, Section 6.2.9, Section 13.4, 13.5, Section 15.2, 15.3,

Additions

A - 6

Section 2.4, 2.6.2, 3.6.3, 5.1.3, 5.5.2, 8.2.2, 8.2.3, 8.2.4, 8.2.6, 8.3.3, 8.3.4, 8.5.2, 8.6.5, 8.8.5, 11.3.2, 13.1.3, 13.2.1, 13.2.4, 15.1.2, 15.3.1

Section 2.1.1, 2.1.2, 2.2, 2.3, 2.3.1, 2.3.2, 2.4, 2.5, 2.5.1, 2.5.3, 2.6.1, 2.7.1, 2.7.2, 2.7.3, 2.8.2, 2.8.4, 2.8.5, 2.8.6, 2.9.1, 2.9.2, 3.1, 3.1.2, 3.2.3, 3.3.5, 3.6, 3.6.1, 3.7, 3.7.2, 3.7.3, 3.8.2, 3.10, 3.10.3, 4.1.1, 4.1.12, 4.2.3, 4.3, 4.3.2, 4.4, 4.4.1, 4.4.3, 4.4.4, 4.5.3, 4.5.4, 4.5.5, 4.5.6, 5.1.3, 5.3.3, 6.1.3, 6.1.4, 6.2, 6.2.1, 6.2.3, 6.2.4, 6.2.5, 6.2.6, 6.2.7, 6.2.8, 6.2.9, 6.2.10, 6.2.11, 7.1.3, 7.1.4, 7.1.5, 7.2.4, 7.3.4, 7.3.5, 7.4.3, 7.5.3, 7.5.4, 8.1, 8.1.2, 8.2.1, 8.2.5, 8.3.1, 8.3.2, 8.3.5, 8.3.6, 8.4, 8.4.5, 8.4.6, 8.5.5, 8.5.6, 8.6.4, 8.6.6, 8.7.5, 8.8, 8.8.2, 8.8.4, 8.8.6, 9.1.2, 9.1.4, 9.1.5, 9.1.6, 9.2.2, 9.2.5, 9.2.6, 9.2.7, 10.1.4, 10.2.4, 10.3.4, 10.3.5, 10.4.4, 10.4.5, 10.5.4, 10.6.4, 10.8.6, 11.1.3, 11.2.2, 11.2.3, 11.3.4, 11.3.5, 12.1, 12.2, 12.2.3, 12.2.4, 12.3.1, 12.3.4, 13.2.3, 13.4.3, 15.1, 15.1.3, 15.2.1, 15.2.3, 15.2.4, 15.3.3, 16.3.2, Appendix 1, Appendix 5

Section 3.2.1, 15.1.1, 15.6, Appendix 4 The icon for GT10 is added.

Section 16.4.4

Section 2.1.1, 2.1.2, 2.3, 2.3.1, 2.5, 2.5.1, 2.5.3, 2.7.1, 2.7.3, 2.8.2, 2.8.5, 2.8.6, 2.9.1, 2.9.2, 3.6, 3.6.1, 3.7.2, 3.7.3, 3.8.2, 4.1.11, 4.3, 4.3.1, 4.4, 4.4.1, 4.4.3, 4.5.1, 4.5.3, 4.5.5, 5.1.3, 5.3.3, 6.2.1, 6.2.5, 6.2.11, 7.3.4, 10.6, 10.6.4, 10.8.4, 11.1, 11.1.3, 11.1.4, 11.2, 11.2.2, 11.2.3, 12.1, 12.3.5, 15.1.1 , 16.1.2, Appendix 2, 6

Section 2.3.2, 2.3.4, 2.5.1, 2.9.2, 3.5, 4.1.10, 5.1.1, 5.8, 6.1.3, 6.1.4, 6.2.6, 8.6.4, 12.3.1, 12.3.2, 12.3.4, 15.2.1, 15.2.2

Section 2.13, 3.5.1, 13.6, 13.7, 14.10

Section 2.5.3, 2.7.1 to 2.7.3, 2.9.2, 2.13, 3.7.2, 3.7.3, Appendix 6

Section 14.11

(Continued to next page)

Partial corrections

Partial additions

Additions

Partial correctionsPartial additions

Dec., 2007 SH(NA)-080530ENG-K Compatible with GT Designer2 Version 2.73B

Section 2.1.1, 2.1.2, 2.2, 2.3.1, 2.4, 2.5.3, 2.7.1, 2.7.2, 2.8.2, 2.9.1, Section 3.1.3, 3.2.3, 3.3.5, 3.6, 3.6.1, 3.6.4, 3.7.2, 3.8.2, Section 4.3.1, 4.4.1, 4.4.3, Section 5.1.3, Section 6.1.3, 6.2.3, Section 7.5.3, Section 8.1, 8.1.1, 8.8.4, Section 16.1.2, Appendix 7

Section 2.5.1, 2.6.1, 2.7.1, 2.7.3, 2.8.2, 2.9.2, Section 3.7.3, 3.7.4, Section 4.2.1, Section 5.1.3, 5.3.3, 5.8.1, Section 7.1.2 to 7.1.5, 7.2.3, 7.3.3, 7.3.6, 7.4.2, 7.5.2, 8.2.4, 8.3.4, 8.4.4, 8.5.4, 8.6.3, 8.7.3, 8.8.3, Section 10.1.3, 10.2.3, 10.3.3, 10.4.3, 10.5.3, 10.6.3, 10.7.3, 10.8.3, Section 16.2.3, 16.2.8, 16.3.3, 16.4.2

Section 8.9, Section 11.4, Section 13.8, Appendix 6

Section 2.1.1, 2.1.2, 2.5, 2.5.3, 2.8.2, 2.8.4, 2.8.5, 2.9.1, 3.6.1, 3.7.2, Section 4.4.1, Section 5.1.3, Section 6.2.5, Section 7.5, 7.5.5, Section 16.2.2, 16.2.8

Section 2.2, 2.7.1, 2.7.2, 2.9.2, Section 6.1.3, 6.1.4, 6.2.3, Section 7.1.3, 7.1.4, Section 8.2.5, 8.8.4, Section 13.3, Section 16.2.6

(Continued to next page)

A - 8

Japanese Manual Version SH-080509-AB

2004 MITSUBISHI ELECTRIC CORPORATION

Section 2.1, 2.1.3, 2.3.3, 2.3.4, 2.5.1, 2.7.2, 2.7.3, 2.8, 2.8.1 to 2.8.10, 2.13, 3.1, 3.1.2, 3.1.3, 3.2.3, 3.2.4, 3.4.3, 3.5.3, 3.6.3, 3.7.2, 3.10.2, 3.12.3, 3.13.2, 4.2.1, 4.4.3, 5.3.3, 5.8.1, 7.3.5, 8.2.2, 8.3.2, 8.4.7, 8.5.2, 9.1.2, 10.2.3, 10.4.5, 10.8.6, 11.3.2, 11.3.5, 12.2.4, 12.3.5, 14.1 to 14.13, 15.2.4, 15.3.7, 15.4.3, 16.1.1, 16.3.8

Section 1.1, 2.1.1, 2.1.2, 2.2, 2.3, 2.3.1, 2.4, 2.5, 2.5.3, 2.6.1, 2.7.1, 2.9.1, 2.9.2, 3.2, 3.3.4, 3.4.2, 3.5, 3.5.1, 3.5.4, 3.6, 3.6.1, 3.6.4, 3.7, 3.7.3, 3.8.2, 3.10, 3.10.3, 4.1.5, 4.2.3, 4.3, 4.3.1, 4.4.1, 4.5.1, 4.5.3 to 4.5.5, 5.1.3, 6.1.3, 6.1.4, 6.2, 6.2.3, 6.2.5, 6.2.6, 6.2.10, 6.2.11, 7.1.3 to 7.1.5, 7.3.4, 7.4.3, 7.5.3, 7.5.4, 8, 8.1, 8.1.2, 8.5.3, 8.5.5, 8.6.2, 8.6.4, 8.6.6, 8.8.2, 8.8.4, 10.1.4, 10.2.4, 10.3.4, 10.4.4, 10.5.4, 10.6.4, 10.7.4, 11.1, 11.2, 12, 12.1, 12.3.1, 12.3.2, 13.4, 13.4.2, 13.4.3, 13.5, 13.5.1, 13.5.3, 13.5.4, 13.6.4, 14, 15.2.1, 16.2.1, 16.3.2, 16.3.4, 16.4.3, Appendix 1, Appendix 5 to Appendix 7

The icon for GT16 is added.

Section 13.10

Section 2.1.1, 2.1.2, 2.3, 2.3.1, 2.3.3, 2.3.4, 2.4, 2.5, 2.5.3, 2.7.1, 2.8.2, 2.8.4, 2.8.5, 2.9.1, 3.5.1, 3.5.3, 3.5.4, 3.6, 3.7.2, 3.8.2, 4.5.1, 5.1.3, 5.8, 6.2.3, 6.2.5, 8.6.4, 8.8.4, 10.3

Section 2.7.2, 2.9.1, 3.5, 13.9.1

Section 15.7

Section 2.1.1, 2.1.2, 2.1.3, 2.3.4, 2.4, 2.5.2, 2.5.3, 2.7.1, 2.7.2, 2.8.2, 2.8.4, 2.8.5, 2.8.10, 2.9.1, 3.1.3, 3.2.3,3.3.4, 3.5.2, 3.5.4, 3.5.6, 3.6, 3.7.2, 3.8.2, 4.3, 4.3.1, 4.4, 4.4.1, 4.4.3, 4.4.4, 6.2.5, 6.2.6, 6.2.7, 6.2.9, 7.1.3, 7.3.4, 8.6.4, 8.8, 10.4.4, 10.8.2, 10.8.4, 13.3.1, 13.3.5, 13.4, 13.5, 13.6.1, 13.6.4, 13.9.1, 13.9.5, 15.7.1, 16.2.2

Section 16.2.2, 16.2.3, 16.2.8, 16.2.9, 16.3.3, Appendix 3, Appendix 7

Partial corrections

Partial additionsAdditionsPartial corrections

Partial corrections

SAFETY PRECAUTIONS A - 1CAUTIONS FOR USING THIS SOFTWARE A - 2REVISIONS A - 4INTRODUCTION A - 9CONTENTS A - 9FUNCTION QUICK REFERENCE A - 21MANUALS A - 33ABBREVIATIONS AND GENERIC TERMS A - 35HOW TO USE THIS MANUAL A - 39

INTRODUCTION

Thank you for choosing Mitsubishi Graphic Operation Terminal (Mitsubishi GOT)

Read this manual and make sure you understand the functions and performance of the GOT thoroughly

in advance to ensure correct use

CONTENTS

A - 10

2.8.10 Multi-channel function check sheet 2 - 227

3.5.4 Setting items 3 - 44

3.10.1 Settings 3 - 1713.10.2 Setting items 3 - 1723.10.3 Precautions 3 - 173

3.12.1 Creating a dialog window 3 - 1773.12.2 Settings 3 - 1793.12.3 Setting items 3 - 1803.12.4 Precautions 3 - 182

3.13.1 Settings 3 - 1853.13.2 Setting items 3 - 1863.13.3 Precautions 3 - 187

4.1.10 Saving/Reading comments as file 4 - 304.1.11 Editing comment saved as Text/CSV file 4 - 344.1.12 Precautions for comment registration 4 - 39

A - 12

5.6 Data Operation Function 5 - 74

6.2.10 Setting items of multi action switch 6 - 1016.2.11 Precautions 6 - 108

8.6 User Alarm Display 8 - 186

A - 16

10.8.5 Touch switches for historical trend graph operation 10 - 148

13.10.5 Precautions 13 - 155

A - 20

Appendix.7.1 GT16, GT15, GT SoftGOT1000, and GT11 App - 10Appendix.7.2 For GT10 App - 45

FUNCTION QUICK REFERENCE

Edit Operation (GT Designer2 Version Basic Operation/Data Transfer Manual)

Sets same attributes to objects or images in the

Displays lines to align figures and objects when

Changes the color(s) of the objects and figures

Changes the switch/lamp figures at the same

Base 1

Base 3 Base 2

Base 1 Replace shapes

Base 3

Base 2

Base 1

Base 3 Base 2

Base 1 Replace devices

A - 22

Object Functions (GT Designer2 Version Screen Design Manual)

Input characters or comments in other

Displays device value via lamp color

Multiple language input

Import Project

Import

Change object name

Touch switch Line A start switch Touch switch Line B start switch

2 Digit/font display

Touch it to switch the screen to such as the

Touch it to switch between the base and

Touch it to switch the monitored controller

Used as the key for inputting numerical

Displays the specified key window at the specified position and displays the cursor on the corresponding object

Page 6-93

Special function switch

A

A B C D

E F G H

Key code switch

Data change switch

D100 55 122 34

A - 24

Displays a history of GOT errors, communication errors or user-created messages at alarm occurrence

Also displays alarms hierarchically

Page 8-101

Pops up a GOT error, communication error

or user-created message at alarm occurrence Also displays alarms hierarchically

Page 8-150

Displays a user-created message at alarm

Displays a GOT error or communication error

Displays a history of user-created messages

13:25 RUN A STOP 13:05 Hight limit over Time message

13:03 Motor trip

307 No monitor device setting Advanced alarm popup display

307 No monitor device setting

307 No monitor device setting

User alarm display

02/04/18 13:25:40 RUN A STOP

System alarm display

307 No monitor device setting

Alarm history display

13:25 RUN A STOP 13:05 Hight limit over 13:03 Motor trip Time message

Scrolling alarm display

Alarm occur Alarm

Parts display

5 Graph/Meter

Displays the past data having been collected

by the logging function in trend graph, starting from the present

Page 10-125

Monitors status of device and write value to device or operates GOT when condition meets

Page 11-1

Parts movement display

Panel meter display

Level display

Trend graph display

Line graph display

Bar graph display

Statistics graph display

Scatter graph display

Historical trend graph display

Status observation function

Write D100: 0 150

A - 26

Outputs the device writing and sound at

Reads the device values and writes to the other device when the trigger condition is satisfied

Page 11-61

Monitors status of device and read/write device data when condition meets

One value can be set to a device

Page 12-12

Monitors status of device and read/write device data when condition meets

Multiple values can be set to a device

The device value can be read/written by the utility

Page 12-25

Collects data such as production management and production status and prints the collected data

Page 13-1

Outputs the GOT monitor screen to printer or

Writes data read by bar code reader to

Time action function

Advanced recipe function

Read /Write

D100: 150 250 D101: 300 500 D102: 208 235

Hardcopy

1350

Bar code

9 Others

Operates the mouse pointer on the personal computer by touching the personal computer screen displayed on the GOT using the RGB display

Page 13-74

Displays or records a video image

Plays a video file

Sends a video file to a personal computer

Page 13-118

Writes data to a device with the operation

Reads and writes IC tag data with RFID

Changes device values on a test window

Remote personal operation

A - 28

Displays the operation status of a sequence

Reads a sequence program from ACPU and

Reads a sequence program from FXCPU

Displays the operation status of a SFC

Monitors and edits a sequence program, or changes current device values in the controller by using the GOT without the dedicated software

Page 14-18

Monitors the buffer memory of the intelligent function module on the dedicated screen to change the data

Page 14-8

Monitors the network status of MELSECNET/

Performs servo monitoring and parameter

System monitoring function

M10 ON M20 OFF D100 255

D199 : 100

D200 : 120

D199 : 100 D200 : 120

Device monitor

Ladder monitoring function

List editor for A

List editor for FX

Performs various monitoring functions, parameter changes and test run for the servo amplifier where a GOT is connected.

Page 14-11

Executes the position display monitor and others of the CNC that is connected to the GOT The position display monitor and others

of the CNC are equivalent to those of the MELDAS dedicated display

Page 14-12

Backs up and restores data for controllers

Copies or deletes machining programs, parameters, and others of the CNC that is connected to the GOT

Page 14-15

Performs remote monitoring and remote maintenance of production site from the office

Page 15-62

Enables data communications between the controllers and databases in the information system (manufacturing execution system) without a communication gateway

Page 15-63

Import a CSV tag file created by the third party programming software to GT Designer2, and set a tag as a device

Page 15-64

Servo amplifier monitor

CNC monitor

Backup/Restore

Restore Backup

Copy/Delete CNC data I/O

Tag import function

Third party programming

software

Device setting Tag file

(CSV)

A - 30

Other Functions (GT Designer2 Version Screen Design Manual)

Operates device values by expression and

Accumulates the offset device value in

Script

if(([b:X1]==OFF)&&([b:X2]==OFF)&&([b:X3]==OFF)) {[w:D10]=1;}

if(([b:X1]==ON)&&([b:X2]==OFF)&&([b:X3]==OFF)) {[w:D10]=2;}

if(([b:X1]==OFF)&&([b:X2]==ON)&&([b:X3]==OFF)) {[w:D10]=3;}

if(([b:X1]==OFF)&&([b:X2]==OFF)&&([b:X3]==ON)) {[w:D10]=4;}

Offset

Numerical value input: D100

Offset device: D200 Write to D110

Data Transmission (GT Designer2 Version Basic Operation/Data Transfer Manual)

Makes the communication settings of the

Makes the settings relevant to GOT display

Sets the screen (BMP file) to be displayed at

Saves the user's operation performed at the

Transimits monitor screen data from PC to

A - 32

Print (GT Designer2 Version Basic Operation/Data Transfer Manual)

Transmits monitor screen data from GOT to

Check the project data displayed on the GT Designer2 against the project data stored in the GOT

Page 8-87

Prints the project information (screen image,

Upload

project data corresponds

to each other.

Print

The following table lists the manual relevant to this product

You can order it as necessary

Stored in the GT Works2/GT Designer2 in PDF format

(Continued to next page)

Related Manuals

(Type code) GT16 User's Manual (Hardware)

Describes the GT16 hardware-relevant contents, including the specifications, part names, mounting,

power supply wiring, external dimensions, and option devices.

(Sold separately)

SH-080928ENG (1D7MD3)

GT16 User's Manual (Basic Utility)

Describes the GT16 utility-relevant contents, including the screen settings, operation method settings,

program/data management, and self check function.

(Sold separately)

SH-080929ENG (1D7MD4)

GT15 User's Manual

(Sold separately)

SH-080528ENG (1D7M23)

GT11 User's Manual

(Sold separately)

JY997D17501 (09R815)

GT11 Handy GOT User’s Manual

(Sold separately)

JY997D20101 JY997D20102 (09R817)

GT10 User's Manual

(Sold separately)

JY997D24701 (09R819)

GT SoftGOT1000 Operating Manual

Describes the screen configuration, functions and using method of GT SoftGOT1000.

(Sold separately)

SH-080602ENG (1D7M48)

GT Designer2 Version2 Basic Operation/Data Transfer Manual

Describes methods of the GOT1000 series installation operation, basic operation for drawing and

transmit-ting data to GOT1000 series

(Sold separately)

SH-080529ENG (1D7M24)

-Describes the GT15 hardware-relevant contents, including the specifications, part names, mounting,

power supply wiring, external dimensions, and option devices.

-Describes the GT15 functions, including the utility.

-Describes the GT11 hardware-relevant contents, including the specifications, part names, mounting, power

supply wiring, external dimensions, and option devices.

-Describes the GT11 functions, including the utility.

-Describes the Handy GOT hardware-relevant contents, including the system configurations, specifications,

part names, mounting, power supply wiring, external dimensions, and option devices.

-Describes the Handy GOT functions, including the utility, and how to make cables.

-Describes the GT10 hardware-relevant contents, including the specifications, part names, mounting, power

supply wiring, external dimensions, and option devices.

-Describes the GT10 functions, including the utility.

A - 34

(Type code) GOT1000 Series Connection Manual (1/3, 2/3, 3/3)

Describes system configurations of the connection method applicable to GOT1000 series and cable

creation

(Sold separately)

SH-080532ENG (1D7M26)

GOT1000 Series Extended / Option Functions Manual

Describes extended functions and option functions applicable to GOT series.

(Sold separately)

SH-080544ENG (1D7M32) GOT1000 Series Gateway Functions Manual

Describes specifications, system configurations and setting methods of the gateway functions.

(Sold separately)

SH-080545ENG (1D7M33) GOT1000 Series MES Interface Function Manual

Describes the specifications, system configurations, and setting method of GT MES interface function.

(Sold separately)

SH-080654ENG (1D7M63)

ABBREVIATIONS AND GENERIC TERMS

Abbreviations and generic terms used in this manual are as follows:

A - 36

Communication unit

Option unit

CC-Link IE controller network communication

Video/RGB unit

Option

Software

GT05-50STAND

(SW5D5C-LLT (-EV) or later versions)

A - 38

License key (for GT SoftGOT1000)

License key (for GT SoftGOT2)

Others

FUJI SYS temperature

(Differs from the True Type fonts settable with GT Designer2)

mounted to the base unit.

network.