Nickel nanoparticles were successfully synthesized by a bipolar electrolyser. The obtained Ni nanoparticles were significantly reduced and distributed homogeneous comparing to the particles synthesized by a conventional DC electrolyser.
Trang 1SYNTHESIS OF NICKEL NANOPARTICLES BY A BIPOLAR
ELECTROLYSER APPLIED FOR FUEL CELL ELECTROLYSER APPLIED FOR FUEL CELL
Pham Van Vinh 1 , Nguyen Thuy Duong 1 , Nguyen Thi Hao 1 , Nguyen Bich Ngan 2
1
Faculty of Physics, Hanoi National University of Education
2
Faculty of chemistry, Hanoi National University of Education
Abstract:
Abstract: Nickel nanoparticles were successfully synthesized by a bipolar electrolyser
The obtained Ni nanoparticles were significantly reduced and distributed homogeneous comparing to the particles synthesized by a conventional DC electrolyser The effect of pulse intensity on the properties of Ni nanoparticles was studied XRD patterns revealed that the sample was pure Ni crystals of FCC structure The pulse intensity has not affected much on the formation of crystal phase while it had a strong impact on the morphology SEM images illustrated that the particles were in the shape of leaf and increased in size with the increase of the pulse intensity Hysteresis loop showed the soft magnetic behaviours of the material The increase of saturation magnetism with the increase of pulse intensity was attributed to the effects of grain size The cyclic voltammogram exhibited that the Ni nanoparticles were a great catalysis for ethanol oxidation reaction This exposed that the Ni nanoparticles have a potential application for directed ethanol fuel cell
Keywords:
Keywords: bipolar electrolyser, nickel nanoparticles, electro catalysis, ethanol oxidation,
fuel cell
Email: vinhpv@hnue.edu.vn
Received 26 August 2018
Accepted for publication 5 December 2018
1 INTRODUCTION
Nowadays, non-renewable energies have been running out Therefore, new energy sources which generate green energy such as solar, wind, tide or chemical fuel related energies have been intereted Fuel cell is an outstanding candidate to solve this problem It has been studied for many years but still not popularly applied because of their high cost The catalysis made of platinum is the main reason for increasing the cost of fuel cell To find the solutions for this issue, recent studies have focused on alloying Pt with other metals such as Ni, Cu, Fe, Co,… to support for Pt [1-3] or searching a new technique to create the special Pt structures [4, 5] Besides, non-Pt catalysis have been attracting the attention of researchers [6, 7] Nickel nanoparticles have played an important role in
Trang 2commercial because of their various applications in electronics, magnetism, energy technology, and biomedicine,… Among these, catalysis is such an enormous utilization because it can reduce the cost of generating green energy Nickel nanoparticles are cheaper and can be synthesized with a large amount compared with noble metals Furthermore, Ni nanoparticles shows a great stability in alkaline medium [8] and high electrocatalytic activity of ethanol oxidation reaction Therefore, Ni nanoparticles promise potential applications as a catalyst for directed ethanol fuel
There are many methods to synthesize Ni nanoparticles such as solution reduction [9], electrolysis method, polyol method [10], or sol-gel method [11] The electrolysis method has been preferred to use because it’s simple and cost effective The DC electrolysis method is common to be used However, using DC current in electrolyzing process results
in creating the large size of particles, usually in microscale [12] To solve the grain size problem, a bipolar electrolyser is expected to synthesize Ni particles in nanoscale Indeed, with bipolar electric current, each electrode will become positive or negative polar alternatively and it can interrupt the ions agglomerating process and decrease the grain size In this study, we focused on fabricating Ni nanoparticles by a bipolar electrolyser and investigated the effect of pulse intensity between two electrodes on the properties of Ni nanoparticles
2 EXPERIMENTAL
0.052g of NiCl2 was dissolved into 80ml of dehydrated water The solution was placed inside ultrasonic cleaner tank during the electrolyzing process with one is Ni electrode and the other one is Pt electrode The synthesized parameters were controlled by a computer The electrolyzing process took up 2h under the condition that the pulse period was 20s and the distance between two electrodes was kept constant of 1cm while the pulse intensities were varied for each sample The sample then was collected from nickel electrodes and was annealed in H2 medium in 1h at 250oC to obtain pure Ni nanoparticles The analysis method XRD, SEM, VSM and CV were used to investigate the crystal structure, morphology, magnetic and catalytic properties of Ni nanoparticles respectively For CV measurement, the sample was mixed with Carbon nanopowder and Nafion before having stuffed in an electrode
3 RESULT AND DISCUSSION
3.1 Effect of pulse intensity on Ni crystal structure
The XRD patterns of nickel nanoparticles at different pulse intensities ranging from 12V to 18V are showed in Fig.3.1 The figure demonstrated that nickel nanoparticles had
Trang 3face-centered cubic lattice structure (fcc) Two peaks with the 2θ degree were 44.56o and 51.91o respectively which suggest two planes (111) and (200) of pure nickel No peaks of nickel compounds are found confirmed the purity of nickel nanoparticles It also indicates that the pulse intensity have not affected much on the process to form the phases of nickel crystal The intensity of two peaks of 12V-sample are higher compared with others
exposing that it is crystalized better
Figure 3.1
Figure 3.1 XRD patterns of Ni nanoparticles synthesized
at different pulse intensities 12V, 16V and 18V
The crystalline size could be determined from the XRD patterns by Scherrer equation:
where D: the average particle size
λ: the wavelength of X-ray ( )
β: FWHM (rad)
θ: the angle of peak position
Let’s calculate with 2θ = 44.56o
Table 3.1.
Table 3.1 The average particle size at different pulse intensities
0 200 400 600 800 1000
2-theta (degree)
18V 16V 12V (111)
(200)
0.9 cos
=
1.54056 o
A
Trang 4The results showed that the crystalline size depended on the pulse intensity during electrolyzing process When the pulse intensity increased from 12V to 18V the full width
at half maximum went down and the crystalline size increased slightly from 35nm to 38nm It could be understood that more and more Ni2+ moved to Ni electrode to create clusters resulting in the increase of crystalline size
3.2 Effect of pulse intensity on Ni particle’s morphology
Figure 3.2 shows the SEM images of synthesized nickel particles at different pulse intensities These images suggested Ni nanoparticles had a shape of leaf with a porous structure This characteristic was very important because it is evidenced that these nickel nanoparticles had high potential to be used for catalytic purposes Among three images, the 12V-sample was the most uniform compared with others It was reasoned by the slower speed of creating particles on Ni electrode’s surface As the pulse intensity increased, the particle size also increased and it was in accordance with the results drawn from XRD patterns
Figure 3.2.
Figure 3.2 SEM images of Ni nanoparticles synthesized at different pulse intensities
18V
Trang 53.3 Effect of pulse intensity on magnetic properties of Ni nanoparticles
Figure 3.3.
Figure 3.3 Hysteresis loops of Ni nanoparticles
synthesized at different pulse intensities
The hysteresis loops in Fig 3.3 whow that all samples synthesized at different pulse intensities behaved as soft magnetic materials because they all had small coercive force Soft magnetic property reconfirms the formation of the crystal of nickel particles The magnetic parameters are presented in the table 3.2
Table 3.2.
Table 3.2 Magnetic parameters of nickel nanoparticles synthesized at different pulse intensities
Pulse
intensities (V)
Saturation Magnetism M s
(emu/g)
Residual Magnetism
M r (emu/g)
Coercive Force
H c (G)
The table illustrated that the magnetic parameters strongly depended on the pulse intensity The higher pulse intensity was, the larger saturation magnetism was The increase of saturation magnetism with the increase in the pulse intensity was the results of the particle size effect, which were showed in the XRD and SEM analysis
3.4 Effect of pulse intensity on catalytic ability of Ni nanoparticles
In the Figure 3.4, the dash lines represented for the sample in KOH medium only whereas the solid lines stand for the sample in KOH and ethanol medium In the case of the
-6000 -4000 -2000 0 2000 4000 6000 -20
-10 0 10 20
H (Oe)
12V 16V 18V
Trang 6samples that measured in KOH medium, there exist an oxidation peak at 500mV The reaction could be describe by following equations:
Ni +2OH- → α-Ni(OH)2 + 2e
(1)
Figure 3.4.
Figure 3.4 The cyclic voltammogram of nickel nanoparticles synthesized at
different pulse intensities in KOH medium only and KOH + C 2 H 5 OH medium
However, the oxidation of Ni (0) to Ni (II) occurred at more negative potential which couldn’t show in the figure and at the considered peak, there was a change from α-Ni(OH)2
to β-Ni(OH)2 and a formation of NiOOH In case of adding ethanol, a peak near 500mV could not be observed while the peaks in the range of 600mV to 700mV appeared The present of new peaks overlaped the peaks near 500mV The reason lied in the fact that nickel oxyhydroxide (NiOOH) was capable of oxidizing some functional groups and that would oxidize ethanol to acetaldehyde before transforming to acetic acid as described in equation 4 [13]
4β-NiOOH + CH3CH2OH + OH- → 4βNi(OH)2 + CH3COO- (4) The peak of 12 V-samples had the highest current density It implied that Ni nanoparticles which were synthesized at lower pulse intensity would perform as higher electrocatalytic activities toward ethanol oxidation Catalytic activity is primarily a surface phenomenon The obtained particles synthesized at lower pulse intensities were small hence increasing contact area resulting in improving the catalytic activity The ethanol oxydation reaction showed a great potential of Ni nanoparticles to be applied for directed ethanol fuel cell
-1000 -500 0 500 1000 -200
-100 0 100 200 300 400
Potential applied (mV)
12V 16V 18V 12V Et 16V Et 18V Et
Trang 74 CONCLUSION
The nano crystal of Nickel nanoparticles in FCC structure were successfully synthesized by bipolar electrolyzing method The pulse intensity effected significantly on morphology and grain size of nanoparticles The particle size of Ni was reduced and uniformed with the decrease of the pulse intensity The optimum pulse intensity for synthesizing Ni nanoparticles was 12V The saturation magnetism of the Ni nanoparticles increases in the increase of the pulse intensity Ni nanoparticles exhibited as a good electrocatalyst toward ethanol oxidation
Acknowledgments: This research is funded by Vietnam National Foundation for
Science and Technology Development (NAFOSTED) under grant number of 103.02-2013.50
REFERENCES
1 Dominic Alexander Notter, K.B.K., Theodoros Karachalios, Nara Tudela Haberland, -Life
cycle assessment of PEM FC applications: Electric mobility and μ-CHP - Energy &
Environmental Science 2015 8(7)
2 Lucci, F.R., Selective hydrogenation of 1,3-butadiene on platinum–copper alloys at the
single-atom limit, - Nature Communications 2015
3 Van Vinh Pham, V.-T.T., Cho Sunglae, Synthesis of NiPt alloy nanoparticles by galvanic
replacement method for direct ethanol fuel cell - International Journal of Hydrogen Energy,
2017 42(18): p 13192-13197
4 Long NV, O.M., Nogami M, Hien TD, Effects of heat treatment and poly(vinylpyrrolidone)
(PVP) polymer on electrocatalytic activity of polyhedral Pt nanoparticles towards their methanol oxidation. - Colloid and Polymer Science, 2011 289: p 1373-1386
5 Peng Z, Y.H., Designer platinum nanoparticles: Control of shape, composition in alloy,
nanostructure and electrocatalytic property. - Nano Today, 2009 4(2): p 143-164
6 Silver nanowire catalysts for alkaline fuel cells - International Journal of Hydrogen Energy,
2008 33(20): p 5773-5778
7 Types of Fuel Cells - U.S Department of Energy, 2010
8 Meisong Guo, Y.Y., Jingbo Hu, Nickel Nanoparticles for the Efficient Electrocatalytic
Oxidation of Methanol in an Alkaline Medium. - Springer US, 2017 8(4): p 392-398
9 Sulekh Chandra, A.K., Praveen KumarTomar, Synthesis of Ni nanoparticles and their
characterizations. - Journal of Saudi Chemical Society, 2014 18(5): p 437-442
10 Kyler J Carroll, J.U.R., Michael D Shultz, Shiv N Khanna, and Everett E Carpenter,
Preparation of Elemental Cu and Ni Nanoparticles by the Polyol Method: An Experimental and Theoretical Approach. - The Journal of Physical Chemistry C, 2011 115(6): p
2656-2664
Trang 811 Falong Jia, L.Z., Xiaoying Shang, and Yan Yang, Non-Aqueous Sol–Gel Approach towards
the Controllable Synthesis of Nickel Nanospheres, Nanowires, and Nanoflowers Advanced
Materials, 2008 20(5): p 1050 - 1054
12 GÖKHAN ORHAN, G.G.G., Effect of electrolysis parameters on the morphologies of copper
powders obtained at high current densities. Journal of the Serbian Chemical Society, 2012
77(5): p 651-665
13 Riyanto, M.R.O., Jumat Salimon, Analysis of ethanol using copper and nickel sheet electrodes
by cyclic voltammetry - The Malaysian Journal of Analytical Sciences, 2007 11(2): p
379-387
CHẾ TẠO HẠT NANO NICKEL ỨNG DỤNG CHO PIN NHIÊN LIỆU BẰNG PHƯƠNG PHÁP ĐIỆN PHÂN
SỬ DỤNG DÒNG LƯỠNG CỰC
Tóm t ắắắắt: t: t: H ạt nano Nickel đã được chế tạo thành công bằng phương pháp điện phân sử dụng dòng lưỡng cực Kích thước hạt và sự phân bố kích thước hạt đã được cải thiện đáng kể so với hạt Nickel chế tạo bằng phương pháp điện phân thông thường sử dụng dòng DC Ảnh hưởng của cường độ xung lên các tính chất của hạt đã được nghiên cứu một cách kỹ lưỡng Giản đồ nhiễu xạ tia X đã chứng tỏ rằng mẫu chế tạo được là đơn pha tinh thể Nickel với cấu trúc lập phương tâm mặt Cường độ xung không ảnh hưởng nhiều lên sự hình thành pha tinh thể nhưng nó lại ảnh hưởng mạnh mẽ lên hình thái và kích thước của hạt Ảnh SEM cho thấy hạt có dạng hình lá và kích thước hạt tăng theo chiều tăng của cường độ xung Đường cong từ trễ cũng cho thất vật liệu chế tạo được là vật liệu sắt từ mềm Sự tăng của từ độ bão hòa theo cường độ xung được cho là hiệu ứng liên quan đến kích thước hạt Phép đo thế quét vòng tuần hoàn cũng đã chứng tỏ hạt nano nickel là một chất xúc tác mạnh trong phản ứng oxy hóa ethanol Điều này cho thấy tiềm năng ứng dụng của hạt nano nickel trong pin nhiên liệu sử dụng ethanol trực tiếp
T ừ ừừ ừ khóa: khóa: khóa: điện phân sử dụng dòng lưỡng cực, hạt nano nickel, xúc tác điện hóa, oxy hóa ethanol, pin nhiên liệu