Contact-Adsorption-Regeneration-Stabilization Process for the Treatment of Municipal Wastewater

ABSTRACT In this work, the application of the contact-adsorption-regeneration-stabilization activated sludge process for the municipal wastewater treatment was investigated by using continuous experiments coupled with adsorption batch experiments. The process optimization for performance evaluation was studied. The obtained appropriate operational parameters of recycle ratio, hydraulic retention time (HRT) of the regeneration tank, HRT of the adsorption tank and solids retention time (SRT) of the system were 40%, 2 h, 30 min, and 6 d, respectively. Adsorptive kinetics and equilibrium were investigated with batch experiments of adsorption. The results showed that the activated sludge concentration was in a positive proportion to its adsorptive capability, but that temperature was in an inverse proportion to the adsorptive capability. Adsorptive equilibrium was reached within 15 min. In addition, the equilibrium data fitted well to both the Freundlich and Langmuir adsorption models.

Contact-Adsorption-Regeneration-Stabilization Process for the Treatment of Municipal Wastewater

Shao-Gen LIU* , **, Bing-Jie NI*, Lin WEl***, Yong TANG*,Han-Qing YU*

*Department of Chemistry, University of Science & Technology of China, Hefei, 230026, China

**Department of Environmental Engineering, Anhui Institute of Architecture & Industry, Hefei

230022, China

***School of Resource and Environmental Engineering, Hefei University of Technology, Hefei

230009, China

ABSTRACT

In this work, the application of the contact-adsorption-regeneration-stabilization activated sludge process for the municipal wastewater treatment was investigated by using continuous experiments coupled with adsorption batch experiments The process optimization for performance evaluation was studied The obtained appropriate operational parameters of recycle ratio, hydraulic retention time (HRT) of the regeneration tank, HRT of the adsorption tank and solids retention time (SRT) of the system were 40%, 2 h, 30 min, and 6 d, respectively Adsorptive kinetics and equilibrium were investigated with batch experiments of adsorption The results showed that the activated sludge concentration was in a positive proportion to its adsorptive capability, but that temperature was in an inverse proportion to the adsorptive capability Adsorptive equilibrium was reached within 15 min In addition, the equilibrium data fitted well to both the Freundlich and Langmuir adsorption models

Keywords: activated sludge, adsorption, adsorptive equilibrium, adsorption model, municipal

wastewater, regeneration

INTRODUCTION

With the sustained and rapid economic growth in the last three decades, China is undergoing massive urbanization Municipal domestic sewage, which results from both the increasing population and the improved lifestyle of the people, is one of the major problems, which affect China’s environmental quality and the sustainable development Municipal wastewater treatment in China faces serious shortage of financing and land area Thus, considering the municipal wastewater treatment situations in China and the existence problems, the development of municipal wastewater treatment systems with small land area requirements and low investment is essential

Recently, a cost-effective and land-saving municipal wastewater treatment process, i.e., the contact-adsorption-regeneration-stabilization (CARS) process, was developed by our group In such a process, activated sludge utilizes its physical, chemical and biological synergistic function to adsorb pollutants (e.g., suspended organic matter, soluble organism and ammonium) in the adsorption tank Then, the sludge with all these pollutants directly flows into the secondary clarifier for solid-liquid separation After this, the concentrated sludge is pumped to the regeneration stabilization tank for bio-regeneration Finally, the renewed activated sludge comes out of the bio-regeneration tank under the hydraulic drive and returns to the adsorption tank for reuse In this process, the high adsorption capacity of activated sludge is fully utilized and can ensure a better effluent quality (Ulrich and Smith, 1951; Jacobsen et al., 1996;

Address correspondence to Han-Qing YU, Department of Chemistry, University of Science &

Grady et al., 1999; Huang et al., 2000) At the same time, the sludge settling characteristics are significantly improved after the bio-flocculation process occurring in the adsorption tank (Bruus et al., 1992; Droppo and Ongley, 1997; Biggs and Lant, 2000; Wilen et al., 2003) As a result, a high concentration of the sludge in regeneration reactor is achieved and the HRT is greatly shortened Therefore, the land area requirement could be significantly reduced and accordingly construction investment would be cut down

This paper reports the experimental results of the CARS process for the municipal wastewater treatment The technical feasibility of this process was demonstrated, and the process optimization was performed In addition, the adsorption characteristics of the activated sludge from the CARS system were evaluated with the adsorptive kinetics and equilibrium experiments

MATERIALS AND METHODS

Reactor configuration and wastewater

Three lab-scale reactors were used to evaluate the CARS process The schematic diagram is shown in Fig 1 The effective volumes of the adsorption tank, the regeneration tank and the secondary clarifier were 5 L, 12 L and 10 L, respectively The adsorption tank had an inflow of 10 L/h Domestic wastewater was collected with a central sewerage network for the preparation of the influent wastewater The composition of the influent was given in Table 1 The average COD concentration in this wastewater was about 250 mg/L

Ef f l uent

Wat er t ank

Mi xer

Pump Adsor pt i on t ank Regener at i on t ank

Pump

Aer at or

Sl udge excl udi ng Secondar y cl ar i f i er

Ai r l i f t

Ret ur n act i vat ed sl udge

I nf l uent

Fig 1 -The schematic diagram of CARS system

Seed sludge

The reactors were inoculated with activated sludge taken from the Wangxiaoying Wastewater Treatment Plant, Hefei, China The seeding sludge had a sludge age of 15 d,

a mixed liquor suspended solids (MLSS) concentration of 6.0 g/L and a sludge volume index (SVI) of 90.5 mL/g

Table 1 - Composition of the Municipal Wastewater Component Level

pH 6.5~7.5

Continuous tests

Four series of experiments were conducted to investigate the individual effect of the solids retention time (SRT), hydraulic retention time (HRT) of the regeneration tank, recycle ratio (R), and HRT of the adsorption tank In Series I, the recycle ratio (R) and the SRT were kept at 40% (with a recycling sludge flowrate of 4 L/h) and 6 d, respectively, the HRT of the regeneration tank was decreased stepwise from 3 h to 1 h for the three reactors, while the HRT of the adsorption tank were kept at 30 min In Series II, R was increased from 20% to 60%, and the SRT, HRT of regeneration tank, and HRT of the adsorption tank were kept at 6 d, 2 h and 30 min, respectively; in Series III, the HRT of the adsorption tank was lowered stepwise from 30 min to 10 min, while the SRT, HRT of the regeneration tank, and R were kept at 6 d, 2 h and 40%, respectively; In Series IV, the SRT was increased stepwise from 3 d to 12 d, the HRT of the regeneration tank, recycle ratio R, and HRT of the adsorption tank were kept at 2 h, 40% and 30 min, respectively Each series consisted of 3-4 runs Each run lasted over 3 weeks to ensure the reactors to reach steady-state before changing to the next condition Effluent compositions were continuously monitored Only those obtained under steady-state conditions are reported here

Batch tests

The sludge samples were taken from the incubation reactors and were then centrifuged and washed using tap water for three times Before the adsorption tests, the sludge was diluted to the required MLSS level with the same mineral solution, and the initial pH of the mixed liquor was adjusted to 7.0 The adsorption experiments were conducted using 150-mL Erlenmeyer flasks in duplicate The flasks were filled with 100-mL activated sludge solution, and spiked with wastewater They were immediately sealed with rubber plugs and were shaken on a thermostatic rotary shaker at 125 rpm and 20°C Samples were collected from the flasks at intervals The mixed liquor was centrifuged at 6000 rpm for 10 min The supernatant samples were acidified to pH 2.0 by 1 M HCl and stored in a refrigerator at 4°C before they were analyzed The adsorption isotherms were developed using different sludge and substrate levels The temperature effect was studied at 20, 30, and 40°C, respectively

Analytical methods

Measurement of MLSS, mixed liquor volatile suspended solids (MLVSS), effluent suspended solids (SS), NH4+-N, PO43--P, and COD was performed according to the Standard Methods (APHA, 1995)

RESULTS AND DISCUSSION

Effect of SRT

The SRT effect on the CARS performance is shown in Fig 2 The results revealed that the SRT had a significance effect on the COD, ammonium and phosphorus removals

An increase in SRT from 3 d to 6 d resulted in a significant increase in the COD and

NH4+-N removals However, a further increase in SRT from 6 d to 12 d led to a little decrease in the COD and NH4+-N removals In general, the PO43--P removal decreased slightly with an increase in SRT The PO43--P removal in the CARS system was mainly attributed to the sludge discharge from the system, which was governed by the SRT Thus, the SRT affected the CARS performance significantly The system had the maximum pollutant removal capacity at an SRT of 6 d

0

20

40

60

80

100

0 10 20 30 40 50

0 10 20 30 40 50 60 70

Time (d)

3 d

6 d

+ -N r

Time (d)

3- -P remo

Time (d) Fig 2 - Variations of COD, NH4+-N, and PO43--P removals vs time at different SRTs

Effect of HRT of the regeneration tank

Fig 3 illustrates the effect of HRT of the regeneration tank on the CARS system performance The COD removal increased with an increase in HRT of the regeneration tank from 1 h to 2 h, but decreased from 2 h to 3 h As shown in Fig 2, the PO43--P removal increased as the HRT of the regeneration tank increased The NH4+-N removal was not very sensitive to the HRT It slightly increased as the HRT increased from 1 h to

2 h, but slightly decreased when the HRT increased from 2 h to 3 h This suggests that the 2 h of HRT of the regeneration tank was appropriate for this CARS process

0

20

40

60

80

0 10 20 30 40 50

0 10 20 30 40 50 60

Time (d)

1 h

2 h

+ -N r

Time (d)

3- -P re

Time (d)

Fig 3 - Variations of COD, NH4+-N, and PO43--P removals vs time at different HRTs of

the regeneration tank

Effect of recycle ratio (R)

The recycle ratio of the CARS process played an important role in the substrate removal They had a significant influence on the output variables (Fig 4) It is found that ±50% fluctuation in the recycle ratio resulted in ±10% fluctuation in the COD removal, ±30%

fluctuation in the NH4+-N removal and ±15% fluctuation in the PO43--P removal An increase in the recycle ratio resulted in an increase in the COD removal and an increase

in NH4+-N and PO43--P removals (Fig 3) Such influences were associated with the direct effect of recycle ratio on the sludge concentrations in the adsorption and regeneration tanks

0

20

40

60

80

100

0 10 20 30 40

0 10 20 30 40 50 60

Time (d)

20%

40%

+ -N remov

Time (d)

3- -P re

Time (d) Fig 4 - Variations of COD, NH4+-N, and PO43--P removals vs time at different recycle

ratios

Effect of HRT of the adsorption tank

0

20

40

60

80

100

0 10 20 30 40 50

0 20 40 60 80 100

Time (d)

10 min

20 min

+ -N rem

Time (d)

3- -P remo

Time (d) Fig 5 - Variations of COD, NH4+-N, and PO43--P removals vs time at different HRTs of

the adsorption tank

The effect of HRT of the adsorption tank to the CARS process is shown in Fig 5 The COD removal changed slightly with a change of the HRT of the adsorption tank The

NH4+-N removal increased with an increase in the HRT The HRT had a similar sensitivity to the PO43--P removal (Fig 4) An increase in the HRT led to a slight increase in the PO43--P removal These results revealed that the selection of the operational parameters of the CARS process had a great influence on the overall system performance

Adsorptive capability of the sludge in CARS system

The adsorptive rate and specific adsorptive capacity of the activated sludge are described with the following equations:

0 0

C

(1)

MLSS

C C

(2) where qt is the specific adsorptive capacity of the sludge (g/g), C0 and Ct are the organic

substance concentrations before and after adsorption at certain time (t) (mg/L), and MLSS is the sludge concentration (mg/L)

Different activated sludge concentrations were firstly applied in the adsorption batch tests to reveal the effect of the sludge concentration on the adsorption of organic substances in the municipal wastewater by sludge Upon approaching the adsorption equilibrium, the adsorptive rate increased with an increase in MLSS concentration, whereas the specific adsorptive capacity decreased with the increasing MLSS concentration, as shown in Fig 5

The relationship between adsorption time and adsorptive rate and specific adsorptive capacity at equilibrium is also shown in Fig 6 The adsorptive rate and specific adsorptive capacity both increased with the increasing adsorption time In addition, the contact time to reach equilibrium extended with the increasing initial organic substance concentrations (data not shown) It took 40 min for the organic substances removal to reach relatively constant at an initial concentration of about 500 mg/L, whereas 30 min for organic substances at an initial concentration of 300 mg/L

0 10 20 30 40 0.03

0.04 0.05 0.06 0.07 0.08

0 100 200 300 400 500 600

20

40

60

80

MLSS (mg/L)

0.00 0.05 0.10 0.15 0.20 0.25

0 10 20 30 40 40

50 60 70 80

Adsorption time (min)

0.04 0.05 0.06 0.07

0.08

Adsorption time (min)

20 oC

30 oC

40 o C

Fig 6 - Effect of biomass concentration, adsorption time, and temperature on adsorptive

rate or specific adsorptive capacity

The temperature is an important factor influencing adsorption Many studies reported that the ability of adsorption increased with the decreasing temperature either for dried sludge (Zhou, 1992; Zhou and Banks, 1993) or for activated carbon (McCreary and Snoeyink, 1980) Therefore, it is hypothesized that there existed common physicochemical principles underlying these adsorption processes As shown in Fig 5, the specific adsorptive capacity of the activated sludge increased with the decreasing temperature from 40°C to 20°C

Adsorption isotherm

The Langmuir and Freundlich adsorption isotherm equations are the most widely used models for adsorption in an aqueous medium The Langmuir and Freundlich equations are expressed as:

m

e m

e

e

q

C bq

q

C = 1 + (3)

F e

n

log = + (4)

where q e is the adsorbed amount of organic substances per gram sludge (mg/g- TSS), Ce

is the solute equilibrium organic substances concentration (mg/L); q m and b are constant characteristic of the system for the Langmuir model that can be considered as an

indicator of adsorptive capacity and appetency, respectively; and K F and n are constant

characteristics of the system for the Freundlich model, which can be respectively considered as an indicator of adsorptive capacity and intensity (Esparza-Soto and Westerhoff, 2003)

Table 2 - The Freundlich and Langmuir models by fitting the experimental data

Values 0.1315 1.3872 0.9886 0.0022 0.7209 0.9534

1.9 2.0 2.1 2.2 2.3 2.4

1.8

1.9

2.0

2.1

2.2

2.3

2.4

0.6 0.8 1.0 1.2

1.4 Experimental data

Freundlich model

log C e

Experimental data Langmuir model

C e (mg/L)

Fig 7 - The linearized Freundlich and Langmuir adsorption isotherms

Although previous studies demonstrated that the biosorption of heavy metallic ions by activated sludge followed the Langmuir mode (Wu et al., 2004), the present study showed that the Freundlich isotherm equation (Fig 7) also matched the experimental results well The obtained values of the constant characteristics for the two models are listed in Table 2

CONCLUSIONS

In this study, technical feasibility of this process was demonstrated The effects of recycle ratio, HRT of the regeneration tank, HRT of the adsorption tank and SRT of the system were evaluated The removal efficiency improved with the increased HRT of the adsorption tank From an engineering application point of view, the appropriate operational parameters of the recycle ratio, HRT of the regeneration tank, HRT of the adsorption tank and SRT of the system were determined to be 40%, 2 h, 30 min, and 6 d, respectively In this CARS system, biosorption instead of biodegradation, was mainly responsible for the organic substance removal from municipal wastewater Both the Freundlich and Langmuir isotherm models matched the biosorption of organic substances by activated sludge well These results demonstrated that the CARS system was a cost-effective and land-saving municipal wastewater treatment process

ACKNOWLEDGEMENTS

The authors wish to thank the National Key Project for Water Pollution Control (2008ZX07103-001 and 2008ZX07316-002), and the Anhui R&D Key Project (07010301022 and 08010302109) for the partial support of this study

REFERENCES

Standard Methods for the Examination of Water and Wastewater (1995) 19th edn,

American Public Health Association/American Water Works Association/Water Environment Federation, Washington DC, USA

Biggs C A and Lant P A (2000) Activated sludge flocculation: on-line determination

of floc size and the effect of shear Water Res., 34, 2542-2550

Bruus J H., Nielsen P H and Keiding K (1992) On the stability of activated sludge

flocs with implications to dewatering Water Res., 26, 1597-1604

Droppo I G and Ongley E D (1997) Flocculation of suspended sediment in rivers of

southeastern Canada Water Res., 26, 65-72

Esparza-Soto M and Westerhoff P (2003) Biosorption of humic and fulvic acids to

live activated sludge biomass Water Res., 37, 2301–2310

Grady Jr C P L., Glen T D and Henry, C L (1999) Biological wastewater treatment: Second edition, Marcel Dekker, Inc

Huang J C and Li L (2000) An innovative approach to maximize primary treatment

performance Water Sci and Tech., 42(12), 209-222

Jacobsen B N., Aruin E and Reinders M (1996) Factors affecting sorption of

pentachlorophenol to suspended microbial biomass Water Res., 30, 13-20

Kennedy K J and Pham T P (1996) Effect of anaerobic sludge source and condition

on biosorption of halogenated aromatics Water Res., 29, 13-20

McCreary J J and Snoeyink V L (1980) Characterization and activated carbon

adsorption of several humic substances Water Res., 14, 151–160

Ulrich A.H and Smith M.W (1951) The biosorption process of sewage and waste

treatment Sewage and Industrial Waste, 23, 1248-1253

Wilen B M and Jin B (2003) The influence of key chemical constituents in activated

sludge on surface and flocculation properties Water Res., 37, 2127-2139

Wu H S., Zhang A Q and Wang L S (2004) Immobilization study of biosorption of

heavy metal ions onto activated sludge, J of Environ Sci., 16, 640–645

Zhou J L (1992) Biosorption and desorption of humic acid by microbial biomass

Chemosphere, 24, 1573-1589

Zhou J L and Banks C J (1993) Mechanism of humic acid colour removal from

natural waters by fungal biomass biosorption Chemosphere, 27, 607–620