Kirigami là nghệ thuật cắt giấy truyền thống của Nhật Bản, với tên gọi được ghép từ hai chữ : “kiru” (có nghĩa là cắt) và “kami” (là giấy). Tính đối xứng là đặc điểm nổi bật nhất trong kirigami truyền thống. Hình bông tuyết, ngũ giác, và bông hoa là những hình ảnh cổ điển quen thuộc đặc trưng cho kirigami mà trong đó, cắt giấy đơn thuần chỉ nhằm tôn lên cấu trúc tối giản, cân xứng nhưng cũng rất linh hoạt của thiết kế. Nghệ thuật cắt giấy được cho là lần đầu tiên xuất hiện trong các đền chùa Nhật Bản như một cách thể hiện lòng thành kính trước các vị thần. Đến khoảng thế kỷ XVII, Kirigami được biết đến rộng rãi khắp châu Á như một hình thức nghệ thuật đích thực. Không chỉ riêng ở Nhật mà cả ở Trung Quốc, người ta tạo nên các thiết kế kirigami để biểu trưng cho những điều tốt đẹp và quan trọng như: Thịnh vượng, Hoàn hảo, Quý phái, Trang nhã hay thậm chí là mối liên kết giữa con người và vũ trụ. Bunraku, một loại hình múa rối Nhật Bản đôi lúc cũng sáng tạo những con rối bằng giấy từ kỹ thuật Kirigami, nhưng vẫn đảm bảo các bộ phận có thể cử động được.
Trang 12
3 5
6
7
8 4
http://www.canon.com/c-park/en/
View of completed model
Assembly Instructions: Six A4 sheets (No.1 to No.6)
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order
(* This way, you can be sure which section is which even after cutting out the sections.)
Sydney O pera Hous e
Sy dney, Austral ia
*This model was designed for Papercraft and may differ from the original in some respects
(1) Build the base.
Insert.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold
Valley fold(dashed and dotted line)
Make a valley fold
Scissors line(solid line)
Cut along the line
Cut in line(solid line)
Cut along the line
Glue spot(Red dot)
Glue parts with the same number together
Glue spot(Green dot)
Glue within the same part
Glue spot(Blue dot)
Glue to the rear of the other part
Glue
The glue spot(colored dot) shows where to apply the glue
Tools and materials
Assembly tip
Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff
Trang 210
11
13
15
14
12
(2) Build the fan-shaped foundation.
Trang 320 21
22
16
19 17
24
25
sides
Insert between the folded sides
Insert
between
the folded
sides
Insert between the folded sides
When assembling this section, first attach parts 21, 22, 24,
and 25 to part 17, then connect the parts together by adjusting
Fold each of parts 21, 22, 24, and 25 before gluing them to part 17.
* Since folding these parts after gluing them
to part 17 may cause the paper on the exterior
to stick out or tear, be sure to glue these parts in place after folding them
Match the borders
of the coloring when gluing these pieces together
Match the borders
of the coloring when gluing these pieces together
Trang 423 27
38 39
30
33
41
29
40 37
36
36 37
34 31
28 41
40
(4) Build the large and small halls and the restaurant.
Assemble parts 33, 35, 38, 45, 52, 55,
and 56 in the same general way.
Glue together.
Assemble parts 30, 32, 34, 39, 44,
50, 53, 54, 57, and 59 in the same general way.
Large hall
Glue in the same way as on the opposite side
Glue in the same way
as on the opposite side
Glue along the dotted line.
Bend this piece slightly before gluing it
Bend this piece slightly before gluing it
Bend this piece slightly before gluing it
Glue in the same way as part 29
Glue one side to part 38 and one side to part 32
Glue parts 28, 29, 40, and 41 in place last, adjusting the assembled parts while doing so.
Trang 558
56
59 60
45 50
43
44
55
54
52
49
48
48
46
42
53 51
61
61
Small hall
Large hall
Small hall
Glue in the same way
as on the opposite side
Glue in the same way
as on the opposite side
Glue in the same way
as on the opposite side
Glue in the same way
as on the opposite side
Glue in the same way as part 46
Bend this piece slightly before gluing it
Bend this piece slightly before gluing it
Bend this piece slightly before gluing it
Bend this piece slightly before gluing it
Glue one side to the rear side
of part 44 and one side
to part 50
Restaurant
Restaurant
Glue parts 46, 47, 48, 49, and 61 in place last, after assembling all these parts together, adjusting the assembled parts while doing so.
(5) Glue the large and small halls and the restaurant
to (3) the lower section of the structure (3).
(3) Lower section of structure
Trang 6(6) Complete the model by gluing the base assembled in step (1) to the foundation assembled
in step (2) and the structure assembled in step (5).
(5) Structure
(2) Foundation
(1) Base
Finished!