Hilux 2015 2018 manual audio visual telematics he thong giai tri

Tài liệu hướng dẫn sửa chữa Hệ thống giải trí trên xe Hilux 2015 2018 manual audio visual telematics he thong giai tri. Cung cấp các thông tin cần thiết cho Kỹ thuật viên tiến hành sửa chữa nhanh chóng, chính xác, hiệu quả.

Trang 1

11/3/17, 10(34 pm Inspection Procedure - Toyota Service Information

Page 1 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000LGZM.html?PUB_TYPE=RM&MODE=3#RM100000000LGZM_06

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL

OK

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Illumination for Panel

Switch does not Come on with Tail Switch ON

CAUTION / NOTICE / HINT

HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting

for Connected Services (w/ Connected Services Function)

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)

Result:

Enter the "Vehicle Signal Check Mode" screen Refer to Check Vehicle Signal in Operation Check

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and DisplayType)>OPERATION CHECK

Trang 2

Page 2 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manu…RM100000000LGZM.html?PUB_TYPE=RM&MODE=3#RM100000000LGZM_06

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radioand Display Type)>PROBLEM SYMPTOMS TABLE

NG

Trang 3

11/3/17, 10(54 pm Service Information - Toyota Service Information

Page 1 of 1 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/pgm/service.html

HILUX >

GGN12#,GGN13#,GUN11#,GUN12#,GUN13#,KUN11#,KUN12#,KUN13#,LAN12#,TGN11#,TGN12#,TGN13# >

2016.01

HelpKeyword

INSPECTIONINSTALLATIONREAR DOOR SPEAKER(for Double Cab)COMPONENTS

REMOVALINSPECTIONINSTALLATIONREAR DOOR SPEAKER(for Smart Cab)RADIO ANTENNA CORD

COMPONENTSREMOVALINSTALLATIONRADIO ANTENNA POLECOMPONENTS

REMOVALINSTALLATIONAMPLIFIER ANTENNACOMPONENTSREMOVALINSTALLATIONSTEREO JACK ADAPTER ASSEMBLYTELEPHONE MICROPHONE

Trang 4

11/3/17, 10(54 pm

Page 1 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LJHX.html

AUDIO / VIDEO AMPLIFIER ANTENNA INSTALLATION

PROCEDURE

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION

Attach the claws to install the No 1 amplifier

Install in this Direction

Connect the connector

c.

for Single Cab:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>INSTALLATION

a.

for Smart Cab:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>INSTALLATION

b.

for Double Cab:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>INSTALLATION

c.

Trang 5

11/3/17, 10(54 pm

Page 2 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LJHX.html

Trang 6

11/3/17, 10(54 pm

Page 1 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LJHZ.html

AUDIO / VIDEO AMPLIFIER ANTENNA REMOVAL

CAUTION:

Some of these service operations affect the SRS airbag

system Read the precautionary notices concerning the

SRS airbag system before servicing

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT

SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

PROCEDURE

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the batteryterminal Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceedingwith work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for Single Cab:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>REMOVAL

a.

for Smart Cab:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>REMOVAL

b.

for Double Cab:

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>REMOVAL

c.

Disconnect the connector

a.

Remove the nut

b.

Trang 7

11/3/17, 10(54 pm

Page 2 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LJHZ.html

Remove in this Direction

Detach the claws and remove the No 1 amplifier

antenna assembly

c.

Trang 8

11/3/17, 10(30 pm

Page 1 of 7 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000US5R.html

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) SYSTEM DIAGRAM

Trang 9

11/3/17, 10(30 pm

Trang 10

11/3/17, 10(30 pm

Trang 11

11/3/17, 10(30 pm

Trang 12

11/3/17, 10(30 pm

Trang 13

11/3/17, 10(30 pm

Trang 14

11/3/17, 10(30 pm

Trang 15

11/3/17, 10(31 pm

Page 1 of 3 https://toyotamanuals.com.au/docs/hilux-service-repair-manual-jul-15-current/N00148/manual/repair/contents/RM100000000LGZ4.html

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) TERMINALS OF ECU

RADIO AND DISPLAY RECEIVER ASSEMBLY

Terminal No.

G37-1 (IG) - G40-7

(GND1) W - BR Illumination (autodimmer) signal

Ignition switch ON,automatic light controlsensor not covered by hand,and light control switch inauto position

Below 1 V

Ignition switch ON,automatic light controlsensor covered by hand,and light control switch inauto position

11 to 14 V

G37-4 (MACC) -

Telephone microphoneassembly powersupply

G37-5 (MIN+) -

G40-7 (GND1) W - BR Telephone microphoneassembly voice signal

See "Check Microphone" inOperation Check

-G37-6 (SNS2) -

Trang 16

11/3/17, 10(31 pm

See "Check Vehicle Signal"

in Operation Check

-G37-17 (SPD) - G40-7

See "Check Vehicle Signal"

G40-7 (GND1) R - BR Telephone microphoneassembly voice signal

See "Check Microphone" inOperation Check

22 (SW2) -

G37-23 (SWG) G - V Steering pad switchsignal

MODE switch pushed 0.27 to 0.35 V

On hook switch pushed 0.86 to 1.03 VOff hook switch pushed 1.51 to 1.79 VVoice switch pushed 2.22 to 2.66 VG37-23 (SWG) - G40-

G3725 (ADPG)

External deviceconnection detectionsignal

External device connected Below 1 VExternal device not

G3726 (VAR+)

-G37-27 (VA-) B - W Sound signal (Right) (When stereo jack used)External device playing

A waveformsynchronized withsound signals isoutputG37-27 (VA-) - G40-7

28 (VAL+) -

G37-27 (VA-) R - W Sound signal (Left) (When stereo jack used)External device playing

A waveformsynchronized withsound signals isoutput

-G40-1 (FR+) - G40-7

(GND1) LG - BR Sound signal (FrontRight) Audio system playing

A waveformsynchronized withsound signals isoutputG40-2 (FL+) - G40-7

A waveformsynchronized withsound signals isoutputG40-3 (ACC1) - G40-7

G40-4 (+B1) - G40-7

Trang 17

11/3/17, 10(31 pm

#: There is no wire color information

*1: for 4 Speakers

*2: for 6 Speakers

*3: for TFT Display Type

*4: except TFT Display Type

*5: w/ DAB Function

G40-5 (FR-) - G40-7

(GND1) L - BR Sound signal (FrontRight) Audio system playing

A waveformsynchronized withsound signals isoutputG40-6 (FL-) - G40-7

A waveformsynchronized withsound signals isoutputG40-7 (GND1) - Body

G41-2 (RL+) - G40-7

(GND1)*1, *2 B - BR Sound signal (RearLeft) Audio system playing

A waveformsynchronized withvoice signals isoutputG41-3 (RR-) - G40-7

(GND1)*1, *2 W - BR Sound signal (RearRight) Audio system playing

A waveformsynchronized withvoice signals isoutputG41-5 (ILL-) - G40-7

-RA-5 (ANT+) - G40-7

Ignition switch ACC, radioswitch on and FM or AM

Trang 18

-11/3/17, 10(35 pm Inspection Procedure - Toyota Service Information

Page 1 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000LH0B.html?PUB_TYPE=RM&MODE=3#RM100000000LH0B_04

REMOVE FOREIGN MATTER

OK 2.CHECK TOUCH PANEL NG

Check for foreign matter on the display

Trang 19

Page 2 of 2 https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000LH0B.html?PUB_TYPE=RM&MODE=3#RM100000000LH0B_04

CLEAN DISPLAY AND RECHECK TOUCH PANEL

3.CHECK TOUCH SWITCH (OPERATION CHECK) NG

OK

NG

3.CHECK TOUCH SWITCH (OPERATION CHECK)

Result:

Enter the "Touch Switch Check" screen Refer to Check Touch Switch in Operation Check

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and DisplayType)>OPERATION CHECK

Trang 20

Page 1 of 6 https://toyotamanuals.com.au/docs/hilux-service-repair-manua…/RM100000000LH00.html?PUB_TYPE=RM&MODE=3#RM100000000LH00_02

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract

setting for Connected Services (w/ Connected Services Function)

Trang 21

Page 2 of 6 https://toyotamanuals.com.au/docs/hilux-service-repair-manu…/RM100000000LH00.html?PUB_TYPE=RM&MODE=3#RM100000000LH00_02

END (USB DEVICE FORMAT IS INCOMPATIBLE, "iPod" VERSION IS INCOMPATIBLE,

OR NO PLAYABLE FILES EXIST) A

B 2.CHECK RADIO WIRING SUB-ASSEMBLY

1.CHECK USB DEVICE OR "iPod"

Result:

2.CHECK RADIO WIRING SUB-ASSEMBLY

Disconnect the USB device or "iPod" from the No 1 stereo jack adapter assembly

a.

Check if playable files are present on the USB device or "iPod"

HINT:

Refer to System Description for playable files

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and DisplayType)>SYSTEM DESCRIPTION

b.

Check if the USB device is a compatible format or "iPod" is a compatible version

HINT:

Refer to System Description for compatible formats and versions

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and DisplayType)>SYSTEM DESCRIPTION

c.

No playable files exist, or

incompatible device format or

Playable files exist, and compatible

Trang 22

Disconnect the radio and display receiver assembly connector

a.

*a Front view of wire harness connector (to Radio and Display Receiver Assembly)

*b Front view of wire harness connector (to No 1 Stereo Jack Adapter Assembly)

Disconnect the No 1 stereo jack adapter assembly connector

a12 (US1)

10 kΩ orhighera2-3 (US1+)

or a1-3(US1+) - Body

ground

Always 10 kΩ orhigher

Trang 23

REPLACE RADIO WIRING SUB-ASSEMBLY

OK 3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (NO 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG Result:

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (NO 1 STEREO JACK ADAPTER ASSEMBLY

POWER SOURCE)

Result:

a2-4 (UGD1)

or a1-4(UGD1) - Body

Proceed to

OKNG

Disconnect the No 1 stereo jack adapter assembly connector

a.

*a Front view of wire harness connector (to No 1 Stereo Jack Adapter Assembly)

Measure the voltage according to the value(s) in the table below

Standard Voltage:

b.

Tester Connection Condition Switch Condition Specified

a11 (USV1)

-a1-4 (UGD1) Ignition switchACC 4.5 to 5.5 V

Proceed to

OK

Trang 24

OK 4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK NG

END OK

NG 5.REPLACE USB DEVICE OR "iPod"

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

Turn the ignition switch off

HINT:

When this malfunction occurs, it is necessary to turn the ignition switch off to make it possible for the

vehicle to recognize a new device when it is connected

·

Refer to System Description for compatible formats and versions

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and

·

Trang 25

NEXT 6.CHECK USB DEVICE OR "iPod"

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

Trang 26

Page 1 of 4 https://toyotamanuals.com.au/docs/hilux-service-repair-manua…/RM100000000LH02.html?PUB_TYPE=RM&MODE=3#RM100000000LH02_07

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Vehicle Speed Signal

Circuit between Radio Receiver and Combination Meter

DESCRIPTION

The radio and display receiver assembly receives a vehicle speed signal from the combination meter assembly to

control the ASL function

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the

diagram below will not operate normally

·

Trang 27

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose

connections

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

Check the output waveform

a.

*a Component with harness connected (Combination Meter Assembly)

Remove the combination meter assembly with the connector still connected

Trang 28

GO TO METER / GAUGE SYSTEM

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TOPROCEED WITH TROUBLESHOOTING

OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY COMBINATION METER ASSEMBLY)

-NG Result:

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Speed-sensitive Automatic Door Lock Function

*7: for Automatic Transmission

Disconnect the G37 radio and display receiver assembly connector

Trang 29

REPAIR OR REPLACE HARNESS OR CONNECTOR

Trang 30

Page 1 of 4 https://toyotamanuals.com.au/docs/hilux-service-repair-manua…/RM100000000LHJ3.html?PUB_TYPE=RM&MODE=3#RM100000000LHJ3_01

TURN "iPhone" OR "iPod touch" ON

A 2.CHECK CONNECTION CONDITION B

USE DEDICATED CABLE

A 3.CHECK USAGE CONDITION B

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Application Link Function cannot be Started

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display

The connected "iPhone" or "iPod

Check that the "iPhone" or "iPod touch" is connected to the head unit using a dedicated cable

a.

Trang 31

RESTART APPLICATION LINK COMPATIBLE APPLICATION A

B 4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

A 5.CHECK "iPhone" OR "iPod touch"

B 6.CHECK APPLICATION

3.CHECK USAGE CONDITION

The application does not

automatically start when the

ignition switch is turned from OFF

to ON

AThe application closes after the

hands-free function is used

The application closes after

another application is started on

the "iPhone" or "iPod touch"

Check that "Connected services" is not illuminated on the information screen of the radio and display

Trang 32

CONNECT APPLICATION LINK COMPATIBLE iPhone" OR "iPod touch"

A 6.CHECK APPLICATION B

INSTALL APPLICATION LINK COMPATIBLE APPLICATION

A 7.CHECK APPLICATION RUNNING STATUS B

6.CHECK APPLICATION

7.CHECK APPLICATION RUNNING STATUS

Result:

touch" is Application Link

compatible

A

touch" is not Application Link

·

An Application Link compatible

Connect the "iPhone" or "iPod touch" to the head unit using a dedicated cable, touch "Connected services"

on the information screen of the radio and display receiver assembly with an Application Link compatible

·

Trang 33

END

Trang 34

USE DEDICATED CABLE

A 2.CHECK USAGE CONDITION B

END A

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Application Link Function Image is not Displayed

HINT:

Type)>PRECAUTION

PROCEDURE

1.CHECK CONNECTION CONDITION

Result:

Check that the "iPhone" or "iPod touch" is connected to the head unit using a dedicated cable

a.

Check the conditions under which the Application Link function is being used

An image is not displayed while

the vehicle is being driven or

Trang 35

B 3.CHECK "iPhone" OR "iPod touch"

RESTART APPLICATION LINK COMPATIBLE APPLICATION

END

A

B

3.CHECK "iPhone" OR "iPod touch"

Check if an image is displayed on the "iPhone" or "iPod touch" when an Application Link compatible

application is running and the "iPhone" or "iPod touch" is disconnected from the head unit

Trang 36

Trang 37

END A

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Application Link Function

is Inoperative

HINT:

Type)>PRECAUTION

PROCEDURE

The Application Link function can

be operated while the vehicle is

The Application Link function

cannot be operated while the

vehicle is being driven or while

the vehicle is stopped

B

Check if the "iPhone" or "iPod touch" can be operated when an Application Link compatible application is

running and the "iPhone" or "iPod touch" is disconnected from the head unit

Trang 38

END

A

B

Trang 39

REPAIR OR REPLACE "iPhone" OR "iPod touch"

OK 2.CHECK USAGE CONDITION NG

AUDIO / VIDEO AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Application Link Function Sound cannot be Heard

HINT:

a.

Sounds cannot be heard after the

ignition switch is turned from OFF

to ON

Trang 40

RESTART APPLICATION LINK COMPATIBLE APPLICATION A

Result:

A

Sounds cannot be heard after the

hands-free function is used

Sounds cannot be heard after

another application is started on

the "iPhone" or "iPod touch"

Check if sounds can be heard from the "iPhone" or "iPod touch" when an Application Link compatible

application is running and the "iPhone" or "iPod touch" is disconnected from the head unit

Tiêu đề	Inspection Procedure - Toyota Service Information
Trường học	Toyota Motor Corporation
Chuyên ngành	Audio Visual Telematics
Thể loại	service manual
Năm xuất bản	2017
Thành phố	Toyota City

Định dạng
Số trang	565
Dung lượng	12,96 MB
File đính kèm	Hilux 2015-2018 Manual_He thong giai tri.zip (11 MB)