35 2005 2006 toyota hilux factory service manual interior and exterior noi that va ngoai that

Tài liệu hướng dẫn sửa chữa hệ thống nội thất và ngoại thất trên xe 35 2005 2006 toyota hilux factory service manual interior and exterior noi that va ngoai that. Cung cấp các thông tin cần thiết cho Kỹ thuật viện tiến hành chẩn đoán, sửa chữa nhanh chóng, chính xác

Trang 1

REMOVAL

1 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2 REMOVE RADIATOR GRILLE

(a) Remove the 2 screws

(b) Using a clip remover, remove the 2 clips

(c) Disengage the 2 clips and remove the radiator grille

3 REMOVE FRONT BUMPER COVER

(a) Apply protective tape to the outer circumference of the front bumper cover, as shown in the illustration.(b) Remove the 6 screws

(c) Using a clip remover, remove the 7 clips

(d) Remove the 2 clips

(e) w/ Fog Light:

(1) Disconnect the 2 fog light connectors

(f) Disengage the 2 claws and remove the front bumper cover

B087564E01

Protective Tape

B087565E04

B087566E01

Trang 2

(g) Remove the 6 clips

4 REMOVE FRONT SPOILER COVER LH (for

X-Runner)

(a) Using a clip remover, remove the 3 clips

(b) Remove the 6 retainers and front spoiler cover

5 REMOVE FRONT SPOILER COVER RH (for

X-Runner)

(a) Using a clip remover, remove the clip

(b) Remove the 6 retainers and front spoiler cover

6 REMOVE FRONT BUMPER EXTENSION LH

(a) for 4WD and Pre Runner:

(1) Remove the 5 retainers and front bumper extension

Trang 3

8 REMOVE FRONT SPOILER CENTER COVER (for Runner)

X-(a) Remove the 6 retainers

(b) Disengage the 7 claws and remove the front spoiler center cover

9 REMOVE FRONT BUMPER HOLE COVER LH (w/o Fog Light)

(a) Disengage the 2 claws and remove the front bumper hole cover

10 REMOVE FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:

Follow the same procedures as for the front bumper hole cover LH

11 REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)

(a) Disengage the 2 claws and remove the fog light

12 REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Follow the same procedures as for the fog light LH

13 REMOVE FRONT BUMPER SIDE SUPPORT

14 REMOVE FRONT BUMPER FILLER LH

(a) Using a clip remover, remove the clip(b) Disengage the 2 claws and remove the front bumper filler

15 REMOVE FRONT BUMPER FILLER RH

Trang 4

17 REMOVE HEADLIGHT ASSEMBLY RH

HINT:

Follow the same procedures as for the headlight LH

18 REMOVE FRONT BUMPER UPPER CENTER

Trang 5

Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working

2 REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

(a) Disconnect the EC mirror connector

(b) Slide the inner rear view mirror cover

(c) Slide the inner rear view mirror

(d) Disengage the 2 claws and remove the inner rear view mirror cover

3 REMOVE SEAT TRACK COVER LH (See page SE-23 )

4 REMOVE SEAT TRACK COVER RH

(a) for Separate Folding Seat Type:

(1) Remove the seat track cover RH (See page

SE-5)

(b) for Separate Seat Type Front Passenger Side:

(1) Remove the seat track cover RH (See page

SE-38)

5 REMOVE FRONT SEAT ASSEMBLY LH (See page

SE-23 )

6 REMOVE FRONT SEAT ASSEMBLY RH

(1) Remove the front seat assembly RH (See page

SE-5)

(1) Remove the front seat assembly RH (See page

Trang 6

9 REMOVE REAR SEAT BACK HINGE COVER

(a) for LH Side:

(1) Remove the rear seat back hinge cover (See page SE-71)

12 REMOVE REAR SEAT BACK HINGE SUB-ASSEMBLY

LH (See page SE-71 )

13 REMOVE REAR SEAT BACK HINGE SUB-ASSEMBLY RH

HINT:

Follow the same procedures as for the rear seat back hinge sub-assembly LH

14 REMOVE FRONT FLOOR FOOTREST (See page IR-1 )

15 REMOVE FRONT DOOR SCUFF PLATE LH

(a) Disengage the 9 claws and remove the front door scuff plate

16 REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Follow the same procedures as for the front door scuff plate LH

17 REMOVE COWL SIDE TRIM BOARD LH

(a) Remove the clip

(b) Disengage the 2 clips and remove the cowl side trim board

18 REMOVE COWL SIDE TRIM BOARD RH

Trang 7

19 REMOVE REAR DOOR SCUFF PLATE LH

(a) Disengage the 8 claws and remove the rear door scuff plate

20 REMOVE REAR DOOR SCUFF PLATE RH

(a) Remove the front door opening trim weatherstrip

22 REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Remove the rear door opening trim weatherstrip

24 REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Follow the same procedures as for the rear door opening trim weatherstrip LH

25 REMOVE FRONT PILLAR GARNISH LH

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the assist grip plug

HINT:

Follow the same procedures as for the opposite side

(b) Remove the 2 screws

(c) Disengage the clip and claw and remove the front pillar garnish

Trang 8

(1) Thoroughly cover the air bag with cloth or nylon

of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration

26 REMOVE FRONT PILLAR GARNISH RH

SUB-(a) for Automatic Transmission:

(1) Remove the rear console upper panel assembly (See page IP-9)

sub-(b) for Manual Transmission:

(1) Remove the rear console upper panel assembly (See page IP-9)

sub-30 REMOVE REAR CONSOLE BOX ASSEMBLY (See page IP-10 )

31 REMOVE INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission) (See page IP-10 )

32 REMOVE FRONT CONSOLE BOX

(a) for Automatic Transmission:

(1) Remove the front console box (See page

IP-10)

(b) for Manual Transmission:

(1) Remove the front console box (See page

Trang 9

Follow the same procedures as for the opposite side.

(a) Disengage the 3 claws and remove the lap belt outer anchor cover

48 REMOVE CENTER PILLAR LOWER GARNISH LH

(a) Remove the bolt and floor anchor of the front seat outer belt

B087415E01

B087416E01

Trang 10

50 REMOVE CENTER PILLAR UPPER GARNISH LH

(b) Disengage the clip and remove the center pillar upper garnish

51 REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:

Follow the same procedures as for the center pillar upper garnish LH

52 REMOVE LUGGAGE COMPARTMENT SIDE TRAY LH

(a) Remove the 3 bolts

(b) Disengage the 8 claws and 3 clips, and remove the luggage compartment side tray

53 REMOVE REAR SEAT BACK CENTER HINGE ASSEMBLY (See page SE-71 )

SUB-54 REMOVE LUGGAGE COMPARTMENT SIDE TRAY RH

(a) w/ Woofer:

(1) Remove the bolt

(2) Disengage the 5 claws and 7 clips, and remove the luggage compartment side tray

(b) w/o Woofer:

(1) Remove the 3 bolts

(2) Disengage the 5 claws and 5 clips, and remove the luggage compartment side tray

B087417E01

B087418E01

B087579E01

B087580E01

Trang 11

55 REMOVE QUARTER TRIM LOWER PANEL LH

(a) Disengage the 2 claws and 2 clips, and remove the quarter trim lower panel

56 REMOVE QUARTER TRIM LOWER PANEL RH

HINT:

Follow the same procedures as for the quarter trim lower panel LH

57 REMOVE QUARTER INSIDE TRIM BOARD LH

(a) Remove the bolt and remove the floor anchor of the rear seat belt outer

(c) Remove the 3 screws

(d) Disengage the 2 clips and remove the quarter inside trim board

58 REMOVE QUARTER INSIDE TRIM BOARD RH

HINT:

Follow the same procedures as for the quarter inside trim board LH

59 REMOVE ROOM LIGHT ASSEMBLY

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and remove the room light lens

Trang 12

60 REMOVE ROOF CONSOLE BOX ASSEMBLY

(a) Remove the screw

(b) Disengage the 2 clips and 3 claws

(c) Disconnect the accessory meter connector and map lamp connector and remove the map lamp

(d) Using a clip remover, remove the wire harness clamp

61 REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Follow the same procedures as for the opposite side.(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover

Trang 13

(b) Remove the 2 screws and assist grip

62 REMOVE ASSIST GRIP PLUG (w/ Curtain Shield Airbag)

HINT:

(a) Using a screwdriver with its tip taped in protective tape, disengage the 2 claws and open the cover

(b) Remove the screw

(c) Disengage the claw and remove the assist grip plug

63 REMOVE VISOR ASSEMBLY LH

(b) Remove the visor from the visor hol

64 REMOVE VISOR ASSEMBLY RH

HINT:

Follow the same procedures as for the visor assembly LH

65 REMOVE VISOR HOLDER

(a) Turn the visor holder 90° counterclockwise and remove it

Trang 14

67 REMOVE ROOF HEADLINING ASSEMBLY

(a) Disconnect the frame wire connector

(b) Disconnect the roof wire connector

(c) Using a clip remover, remove the 2 wire harness clamps

(d) Remove the roof headlining from the vehicle

68 REMOVE ROOF HEADLINING PAD

(a) Remove the 2 roof headlining pads from the roof headlining

Trang 16

24 REMOVE FRONT BUMPER EXTENSION ASSEMBLY LH

SUB-(a) Remove the 3 nuts and front bumper extension

25 REMOVE FRONT BUMPER EXTENSION ASSEMBLY RH

Trang 17

Follow the same procedures as for the headlight LH.

11 INSTALL FRONT BUMPER FILLER LH

(a) Engage the 2 claws and install the front bumper

filler

(b) Install the clip

12 INSTALL FRONT BUMPER FILLER RH

(a) Engage the claw and install the front bumper side

support

(b) Tighten the screw

14 INSTALL FRONT BUMPER HOLE COVER LH (w/o

16 INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

(a) Engage the 2 claws and install the fog light

17 INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

Trang 18

(b) Install the 6 retainers.

19 INSTALL FRONT BUMPER EXTENSION LH

(a) for 4WD and Pre Runner:

(1) Install the front bumper extension with the 5 retainers

21 INSTALL FRONT SPOILER COVER LH (for X-Runner)

(a) Install the front spoiler cover with the 6 retainers.(b) Install the 3 clips

22 INSTALL FRONT SPOILER COVER RH (for X-Runner)

(a) Install the front spoiler cover with the 6 retainers.(b) Install the clip

B087678E01

B087577E01

B087576E01

B087573E01

Trang 19

23 INSTALL FRONT BUMPER COVER

(a) Install the 6 clips

(b) Engage the 2 claws and install the front bumper

cover

(c) Connect the 2 fog lamp connectors (w/ fog lamp)

(d) Install the 9 clips

(e) Tighten the 6 screws

24 INSTALL RADIATOR GRILLE

(a) Engage the 2 clips and install the radiator grille

(b) Install the 2 clips

(c) Tighten the 2 screws

25 CONNECT CABLE TO NEGATIVE BATTERY

TERMINAL

Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)

26 PREPARE VEHICLE FOR HEADLIGHT AIMING

ADJUSTMENT (See page LI-5 )

B087570E01

B087566E01

B087565E03

Trang 20

29 INSPECT HEADLIGHT AIMING (See page LI-7 )

30 ADJUST HEADLIGHT AIMING (See page LI-9 )

31 PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT (See page LI-14 )

32 PREPARE FOR FOG LIGHT AIMING (See page LI-14 )

33 INSPECT FOG LIGHT AIMING (See page LI-16 )

34 ADJUST FOG LIGHT AIMING (See page LI-17 )

Trang 21

REMOVAL

2 REMOVE REAR BUMPER BAR

(a) w/ Towing hitch:

(1) Disconnect the 2 No 3 wire frame connectors.(2) Loosen 2 bolts A

(4) Disengage the 2 pins and remove the rear bumper bar

(b) w/o Towing hitch:

(1) Disconnect the 2 license lamp connectors.(2) Loosen the 2 bolts

(4) Disengage the 2 pins and remove the rear bumper bar

Pins

B087517E02

Pins

B087516E02

Trang 22

3 REMOVE REAR BUMPER SPOILER LH (for Runner)

X-(a) Using a clip remover, remove the 2 clips

(b) Remove the screw

(c) Disengage the 4 clips and remove the rear bumper spoiler

4 REMOVE REAR BUMPER SPOILER RH (for Runner)

X-HINT:

Follow the same procedures as for the rear bumper spoiler LH

5 REMOVE REAR BUMPER COVER

(a) w/ Towing Hitch:

(1) Disengage the 3 claws and remove the receiver hitch cap

HINT:

(3) Remove the hitch ball

(b) Using a screwdriver with its tip in protective tape, disengage the 2 claws and remove the rear bumper cover lower

Trang 23

(c) Remove the 4 bolts

(d) Disengage the 4 claws and remove the rear bumper cover

(e) Remove the 2 nuts from the rear bumper bar

6 REMOVE REAR BUMPER PLATE

(a) Remove the 3 clips

(b) Disengage the 14 claws and remove the rear bumper plate

7 REMOVE REAR BUMPER BAR REINFORCEMENT SUB-ASSEMBLY (w/o Towing Hitch)

(a) Remove the 10 bolts and rear bumper bar reinforcement

B087522E01

B087523E01

B087518E01

B087524E01

Trang 24

8 REMOVE REAR BUMPER ARM SUB-ASSEMBLY LH

(w/o Towing Hitch)

(a) Remove the 2 bolts and rear bumper arm

9 REMOVE REAR BUMPER ARM SUB-ASSEMBLY RH

HINT:

Follow the same procedures as for the rear bumper arm LH

10 REMOVE RECEIVER HITCH BRACKET

SUB-ASSEMBLY (w/ Towing Hitch)

(a) Disconnect the 2 license light connectors

(b) Remove the 10 bolts and receiver hitch bracket

11 REMOVE NO 3 FRAME WIRE (w/ Towing Hitch)

(a) Using a clip remover, remove the 2 wire harness

clamps

(b) Remove the 2 bolts and No 3 frame wire

12 REMOVE REAR BUMPER PLATE LH

(a) Remove the 2 nuts

(b) Disengage the claw and remove the rear bumper

Trang 26

(b) Install the bumper moulding mounting plate onto the license plate light

(c) Engage the claw and install the license plate light

(d) Install the screw

2 INSTALL REAR BUMPER BAR CORNER

4 INSTALL REAR BUMPER PLATE LH

(a) Engage the claw and install the bumper plate

(b) Install the 2 nuts

6 INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH

(a) Install the rear bumper arm with the 2 bolts

Torque: 19 N*m (195 kgf*cm, 14 ft.*lbf)

7 INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH

Trang 27

9 INSTALL NO 3 FRAME WIRE (w/ Towing Hitch)

(a) Install the No 3 frame wire with the 2 bolts

(b) Install the 2 wire harness clamps

10 INSTALL RECEIVER HITCH BRACKET ASSEMBLY (w/ Towing Hitch)

SUB-(a) Install the receiver hitch bracket with the 10 bolts

Trang 28

11 INSTALL REAR BUMPER PLATE

(a) Engage the 14 claws and install the rear bumper

No 1 plate

(b) Install the 3 clips

12 INSTALL REAR BUMPER COVER

(a) Install the 2 nuts into the rear bumper bar

(b) Engage the 4 claws and install the rear bumper pad center

(c) Tighten the 4 bolts

(d) Engage the 2 claws and install the rear bumper

cover lower

HINT:

(e) w/ Towing Hitch:

(1) Install the hitch ball

(2) Tighten the 2 bolts

B087518E01

B087523E01

B087522E01

B088213E01

Trang 29

(b) Tighten the screw.

(c) Install the 2 clips

14 INSTALL REAR BUMPER SPOILER RH (for Runner)

X-HINT:

Follow the same procedures as for the rear bumper spoiler LH

15 INSTALL REAR BUMPER BAR

(a) w/ Towing hitch:

(1) Engage the 2 pins and remove the rear bumper bar

Trang 30

(b) w/o Towing hitch:

(1) Engage the 2 pins and install the rear bumper bar

(3) Connect the 2 license lamp connectors

16 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)

Pins

B088211E02

Trang 31

1 INSTALL ROOF WIRE

2 INSTALL ROOF HEADLINING PAD

(a) Install 2 new roof headlining pads onto the roof headlining

3 INSTALL ROOF HEADLINING ASSEMBLY

(a) Install the roof headlining into the vehicle

Trang 32

(b) Install the 2 wire harness clamps

(c) Connect the roof wire connector

(d) Connect the frame wire connector

4 INSTALL COAT HOOK

HINT:

(a) Turn the coat hook 90° clockwise and install it

5 INSTALL VISOR HOLDER

HINT:

(a) Turn the visor holder 90° clockwise and install it

6 INSTALL VISOR ASSEMBLY LH

(a) Install the visor into the visor holder

(b) Tighten the 2 screws

7 INSTALL VISOR ASSEMBLY RH

(a) Engage the claw and install the assist grip plug

(b) Tighten the screw

Trang 33

(c) Engage the 2 claws and close the cover

9 INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

Follow the same procedures as for the opposite side.(a) Install the assist grip with the 2 screws

(b) Engage the 2 claws and close the cover

10 INSTALL ROOF CONSOLE BOX ASSEMBLY

(a) Install the wire harness clamp

B087594E01

B087423E01

B087431E01

B087595E01

Trang 34

(d) Tighten the screw.

11 INSTALL ROOM LIGHT ASSEMBLY

(a) Connect the room light connector

(b) Engage the 3 claws and install the room light

(c) Engage the 2 claws and install the room light lens

12 INSTALL QUARTER INSIDE TRIM BOARD LH

(a) Engage the 2 clips and install the quarter inside trim board

B087456E01

B087468E01

B087469E01

B087421E01

Trang 35

(c) Engage the claw and close the cover

(d) Install the floor anchor of the rear seat belt outer with the bolt

Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf) NOTICE:

• Make sure that the rear seat outer belt is oriented in the correct direction when installing.

• Be careful not to place the rear seat outer belt over the convex areas of the floor panel.

13 INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:

Follow the same procedures as for the quarter inside trim board LH

14 INSTALL QUARTER TRIM LOWER PANEL LH

(a) Engage the 2 claws and 2 clips, and install the quarter trim lower panel

15 INSTALL QUARTER TRIM LOWER PANEL RH

Trang 36

(b) w/o Woofer:

(1) Engage the 5 claws and 5 clips, and install the luggage compartment side tray

17 INSTALL REAR SEAT BACK CENTER HINGE ASSEMBLY (See page SE-77 )

SUB-18 INSTALL LUGGAGE COMPARTMENT SIDE TRAY LH

(a) Engage the 8 claws and 3 clips, and install the luggage compartment side tray

(b) Tighten the 3 bolts

19 INSTALL CENTER PILLAR UPPER GARNISH LH

(a) Engage the clip and install the center pillar upper garnish

20 INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:

Follow the same procedures as for the center pillar upper garnish LH

21 INSTALL CENTER PILLAR LOWER GARNISH LH

(a) Engage the 2 claws and 2 clips, and install the center pillar lower garnish

(b) Install the floor anchor of the front seat outer belt with the bolt

Trang 37

24 INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (See page IP-18 )

25 CONNECT PASSENGER AIRBAG CONNECTOR

26 INSTALL INSTRUMENT SIDE PANEL (See page IP-20 )

27 INSTALL INSTRUMENT LOWER COVER ASSEMBLY (See page IP-20 )

SUB-28 INSTALL INSTRUMENT LOWER PANEL (See page

38 INSTALL FRONT CONSOLE BOX

(a) for Automatic Transmission:

(1) Install the front console box (See page IP-24).(b) for Manual Transmission:

(1) Install the front console box (See page IP-23)

39 INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission) (See page IP-24 )

40 INSTALL REAR CONSOLE BOX ASSEMBLY (See page IP-24 )

41 INSTALL REAR CONSOLE UPPER PANEL ASSEMBLY

SUB-(a) for Automatic Transmission:

(1) Install the rear console upper panel assembly (See page IP-25)

sub-B087415E01

Trang 38

(b) for Manual Transmission:

(1) Install the rear console upper panel assembly (See page IP-25)

sub-42 INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake) (See page IP-25 )

43 INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake) (See page IP-25 )

44 INSTALL FRONT PILLAR GARNISH LH

(a) Install the 3 wire harness clamps (LH side only)

(b) Engage the claw and clip, and install the front pillar garnish

(c) Tighten the 2 screws

(d) Engage the 2 claws and install the assist grip plug

(a) Install the rear door opening trim weatherstrip

47 INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

Trang 39

48 INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Install the front door opening trim weatherstrip

49 INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Follow the same procedures as for the front door opening trim weatherstrip

50 INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the 8 claws and install the rear door scuff plate

51 INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Follow the same procedures as for the rear door scuff plate LH

52 INSTALL COWL SIDE TRIM BOARD LH

(a) Engage the 2 clips and install the cowl side trim board

(b) Install the clip

53 INSTALL COWL SIDE TRIM BOARD RH

HINT:

Follow the same procedures as for the cowl side trim board LH

54 INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the 9 claws and install the front door scuff plate

55 INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Follow the same procedures as for the front door scuff plate LH

56 INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY

LH (See page SE-77 )

57 INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY RH

HINT:

Follow the same procedures as for the rear seat back hinge sub-assembly LH

58 INSTALL FRONT FLOOR FOOTREST (See page IR-1 )

59 INSTALL REAR SEAT BACK ASSEMBLY LH (See page SE-77 )

60 INSTALL REAR SEAT BACK ASSEMBLY RH (See page SE-90 )

B087413E01

B087412E01

B087438E01

B087411E01

Trang 40

61 INSTALL REAR SEAT BACK HINGE COVER

(a) for LH Side:

(1) Install the rear seat back hinge cover (See page SE-78)

65 INSTALL FRONT SEAT ASSEMBLY RH

(1) Install the front seat assembly RH (See page

SE-19)

(1) Install the front seat assembly RH (See page

SE-48)

66 INSTALL SEAT TRACK COVER LH (See page SE-34 )

67 INSTALL SEAT TRACK COVER RH

(1) Install the seat track cover RH (See page

SE-19)

(1) Install the seat track cover RH (See page

Tiêu đề	35 2005 2006 Toyota Hilux Factory Service Manual Interior And Exterior
Thể loại	service manual
Năm xuất bản	2005

Định dạng
Số trang	130
Dung lượng	11,47 MB
File đính kèm	2005-2006-Toyota-Hilux_Noi that va ngoai that.zip (8 MB)