Industrial Safety and Health for Goods and Materials Services - Chapter 17 potx

17 LiftingIt is probably safe to assume that workers in retail, wholesale, and warehousing perform a large number of lifting tasks as an integral part of their job duties some of which c

17 Lifting

It is probably safe to assume that workers in retail, wholesale, and warehousing perform a large number of lifting tasks as an integral part of their job duties some of which could be both heavy and at times awkward Employers in these industry sectors should lift carefully since overexertion and back injuries are the leading causes of injuries It should not be a foregone conclusion that back injuries are an acceptable part of doing business Efforts should be directed toward prevention although many employers as well as workers view lifting as a natural activity that everyone knows how to do correctly This has proven to be a false belief

17.1 BACK INJURIES

Back disorders can develop gradually as a result of microtrauma brought about by repetitive activity over time or can be caused by a single traumatic event Because of the slow and progressive onset of this internal injury, the condition is often ignored until the symptoms become acute, often resulting in disabling injury Acute back injuries can be the immediate result of improper lifting techniques and=or lifting loads that are too heavy for the back to support While the acute injury may seem to

be caused by a single well-defined incident, the real cause is often a combined interaction of the observed stressor coupled with years of weakening of the musculo-skeletal support mechanism by repetitive microtrauma Injuries can arise in muscle, ligament, vertebrae, and disks, either singly or in combination

Although back injuries account for no work-related deaths, they do account for a significant amount of human suffering, loss of productivity, and economic burden

Lifting is an integral part of goods and material handling

on compensation systems Back disorders are one of the leading causes of disability for people in their working years and afflict over 600,000 employees each year with a cost of about $50 billion annually in 1991 according to National Institute for Occupational Safety and Health (NIOSH) The frequency and economic impact of back injuries and disorders on the workforce are expected to increase over the next several decades as the average age of the workforce increases and medical costs go up

17.2 BACK DISORDERS

Back disorders result from exceeding the capability of the muscles, tendons, disks, or the cumulative effect of several contributors:

. Reaching while lifting

. Poor posture—how one sits or stands (Figure 17.1)

. Stressful living and working activities—staying in one position for too long

. Bad body mechanics—how one lifts, pushes, pulls, or carries objects

. Poor physical condition—losing the strength and endurance to perform physical tasks without strain

. Poor design of job or workstation

. Repetitive lifting of awkward items, equipment, or (in health care facilities)

patients

Awkward postures FIGURE 17.1 Stretching and poor posture can cause back injuries (Courtesy of the Occupational Safety and Health Administration.)

. Twisting whi le liftin g

. Bending while liftin g

. Maintain ing bent postures

. Heavy liftin g

. Fatigue

. Poor footi ng such as slippery floors or const rained postu re

. Lifting with forcef ul movem ent

. Vibration, such as with lift truck drive rs, delivery drive rs, etc.

Before a lift is perfor med some a ctions need to be taken to assur e the lift is a safe one The se are as follow s:

. Checking the object before a lift is attempt ed by testing every load before

lifting by pushing the object with your hands or feet to see how easil y it moves Thi s gives an idea of how heavy it is Remem ber, a smal l size does not always mean a ligh t load

. Check to make sure the load is packed correctly Make sure the weight is

balanced and packed so it would not move around Loose pieces inside a box can cause accide nts if the box becomes unbala nced

. Check to see if the load can be gripped easil y Be sure that you have a tigh t

grip before lif ting Objects wi th handle s can be lifted in a safer manne r

. Check to see if the load is withi n easy reach An injury can occur if the back

is arched when lifting a load To prevent a ba ck injury use a ladder when lifting some thing over h ead level

. Determine that the best way to pick up an object is being used Use slow

and smoo th movement s Hurried, jerky movem ents can strain musc les in the back Keep the bod y facin g the object while lifting Twis ting while lifting can injure the back Keep the load close to the body Having to reach and carry an object may hurt the back Lifting with the legs should be done only when the load can be straddled To lift with the legs, bend the knees while keeping the back straight Try to carry the load in the space between the shoulder and the waist This puts less strain on the back muscles

. Follow the steps sugges ted in Figure 1 7.2 to make a safe lift.

17.3 SYMPTOMS AND CONTRIBUTORS TO INJURIES

Signs and symptoms include pain when attempting to assume normal posture, decreased mobility, and pain when standing or rising from a seated position

At times the following are contributors to work-related back injuries:

. Congenital defects of the spine

. Increase in static standing or sitting tasks

. An aging workforce

. Decreases in physical conditioning and exercise

. Lack of awareness of workplace hazards

. Job dissatisfaction

Manual materials handling is the principal source of compensable injuries in the American workforce, and four out of five of these injuries will affect the lower back

Good lifting techniques

When lifting, remember to

Avoid overloading

Stop and look at the load’s

1 Weight

2 Size

3 Shape

Do not twist

1 Move foot in direction

of turn

2 Move entire body

Re-position the load

1 Tense stomach muscles

2 Keep load close to body

3 Place feet around load

4 Grip corners

Tense stomach muscles Straighten back

Bend at hips

FIGURE 17.2 Steps to follow in making a safe lift

17.4 RECORDS REVIEW: OSHA 300 LOG

Note when back or other musculoskeletal disorders appear excessive from lost work day injury and illness (LWDII) rate calculations Understand that excessiveness is relative, since there is no set limit that delineates safe from unsafe A better measure

is to look for trends of escalating number of injuries or of increasing severity of injuries Comparing your target population with Bureau of Labor Statistics (BLS) data, other company rates, other lines, departments, wings, or occupational titles can yield a meaningful measuring point to gauge excessiveness

Back injuries should be treated as an injury on the OSHA (Occupational Safety and Health Administration) 300 log regardless of whether the injury was the result of

an acute or chronic exposure To determine if trends exist, at least several years of the OSHA 300 log will have to be reviewed Record or copy information, including occupational titles, departments, dates of injury, or illness, from the OSHA 300 log and pertinent OSHA 301 (or equivalent)

17.5 EVALUATING BACK INJURIES

The following techniques can be used to assess why back injuries occurred:

. Use a walkaround.

. Interview employees about their opinion on the difficulty of the task as well

as personal experiences of back pain

. Observe worker postures and lifting.

. Determine weight of objects lifted.

. Determine the frequency and duration of lifting tasks.

. Measure the dimensions of the workplace and lift.

. Videotapes should be taken of the work task for later review and for

evidence of recognized musculoskeletal hazards

17.6 MANUAL LIFTING

Repetitive material handling increases the likelihood of a back disorder Principal variables in evaluating manual lifting tasks to determine how heavy a load can be lifted are the horizontal distance from the load to the employee’s spine, the vertical distance through which the load is handled, the amount of trunk twisting the employee utilized during the lifting, the ability of the hand to grasp the load, and the frequency with which the load is handled Additional variables includefloor and shoe traction, space constraints, two-handed lifts, size, and stability of the load

17.7 PREVENTION AND CONTROL

Generally, the task can be altered to eliminate the hazardous motion and=or change the position of the object in relation to the employee’s body—such as adjusting the height of

a pallet or shelf Manual handling tasks should be designed to minimize the weight, range of motion, and frequency of the activity Work methods and stations should be designed to minimize the distance between the person and the object being handled Platforms and conveyors should be built at about waist height to minimize awkward postures Conveyors or carts should be used for horizontal motion whenever possible Reduce the size or weight of the objects lifted High-strength push–pull requirements are undesirable, but pushing is better than pulling Material handling equipment should be easy to move, with handles that can be easily grasped in an upright posture (Figure 17.3) Workbench or workstation configurations can force people to bend over Cor-rections should emphasize adjustments necessary for the employee to remain in a relaxed upright stance or fully supported seated posture Bending the upper body and spine to reach into a bin or container is highly undesirable The bins should be elevated, tilted, or equipped with collapsible sides to improve access Repetitive or sustained twisting, stretching, or leaning to one side are undesirable Corrections could include repositioning bins and moving employees closer to parts and con-veyors Store heavy objects at waist level Provide lift-assist devices and lift tables

17.8 CONTROLS AND WORK PRACTICES

The following are controls and other methods that address the prevention of back injuries at the workplace:

. Engineering controls are the preferred mechanism to address interventions. . Worker training and education should include general principles of

ergo-nomics, recognition of hazards and injuries, procedures for reporting haz-ardous conditions, and methods and procedures for early reporting of

FIGURE 17.3 Use a handtruck to avoid lifting and carrying task (Courtesy of the Occupa-tional Safety and Health Administration.)

injuries Additionally, job-specific training should be given on safe work practices, hazards, and controls The training should include practical sessions where workers are taught and practice safe lifting techniques under expert supervision

. Strength andfitness training can reduce compensation costs

. Rotating of employees, providing a short break every hour, or using a

two-person lift may be helpful Rotation is not simply a different job, but must

be a job that utilizes a completely different muscle group from the ones that have been over-exerted

. Standing for extended periods places excessive strain on the back and legs.

Solutions include a footrest or rail, resilientfloor mats, height-adjustable chairs or stools, and opportunities for the employee to change position

. Where employees are seated the chairs or stools must be chosen properly.

Proper adjustable lumbar support must be provided

. Static seated postures with bending or reaching should be avoided.

17.9 SUMMARY

To review safe lifting, the legs should be used and not the back To pick up a load stand close to the load, bend the knees while maintaining the backs natural curve Grip the loadfirmly and push the body and load up slowly and smoothly with the legs

To put down a load do not twist the body Bend the knees to lower the load and place the load on the edge of a surface, then slide it back

At times two persons will be needed to lift Put one person in charge to say when

to lift Both individuals should lift at the same time while keeping the load level and unload at the same time (Figure 17.4)

Lifting bulky loads FIGURE 17.4 Two person lifts reduce the strain of a single person lift (Courtesy of the Occupational Safety and Health Administration.)