IEC 62271 202 2014/COR1 2015 – 1 – IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE IEC 62271 202 Edition 2 0 2014 03 High voltage switchgear and control[.]
Trang 1INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
IEC 62271-202 Edition 2.0 2014-03 High-voltage switchgear and controlgear –
Part 202: High-voltage/low-voltage prefabricated
substation
IEC 62271-202 Édition 2.0 2014-03 Appareillage à haute tension – Partie 202: Postes préfabriqués haute tension/basse tension
C O R R I G E N D U M 1
Corrections to the French version appear after the English text
Les corrections à la version française sont données après le texte anglais
Figure AA.6 – Selection of tests on high voltage interconnections for class IAC-A
Replace the existing figure by the following new figure:
Trang 2(1) IEC 62271-200:2011
* For phase to ground test the current value to be stated by the manufacturer
* For phase to phase test the current will be 87 % of the rated short-time withstand current
(2) The time may be stated by the manufacturers, taking into account the time-setting of the protection
Figure AA.6 – Selection of tests on high voltage interconnections for class IAC-A
C
Yes
No
Protection of operators (open doors
to HV switchgear)
HV interconnections
Protection
by HRC current-limiting fuses
Phase-to-ground
or phase-to-phase test Reduced values (1) + (2)
No test
Yes
No test
Insulated ground-shielded type tested Interconnections (see AA.6)
No
Protection by circuit-breaker
Solid insulated Interconnections (see AA.6)
Solid insulated Interconnections (see AA.6)
Three-phase test
Full current and
reduced time (2)
No (no protection) Yes
No
Phase-to-ground
or phase-to-phase test Reduced current (1) and full time
Three-phase test Full current and full time
Trang 3Figure AA.7 – Selection of tests on high voltage interconnections for class IAC-B
Replace the existing figure by the following new figure:
Trang 4(1) Applicability of phase to ground or phase to phase test according to the criteria in AA.5.2.1 of IEC 62271-200:2011
* For phase to ground test the current value to be stated by the manufacturer
* For phase to phase test the current will be 87 % of the rated short-time withstand current
(2) The time may be stated by the manufacturers, taking into account the time-setting of the protection
Figure AA.7 – Selection of tests on high voltage interconnections for class IAC-B
IECIE
Yes
No
Protection of publics (closed doors)
HV interconnections
Protection
by HRC current-limiting fuses
Phase-to-ground
or phase-to-phase test Reduced values (1) + (2)
No test
Yes
No test
Insulated,ground-shielded type tested Interconnections (see AA.6)
No
Protection by circuit-breaker
Solid insulated Interconnections (see AA.6)
Solid insulated Interconnections (see AA.6)
Three-phase test
Full current and
reduced time (2)
No (no protection) Yes
No
Phase-to-ground
or phase-to-phase test Reduced current (1) and full time
Three-phase test Full current and full time
Trang 5Corrections à la version française:
Figure AA.6 – Sélection des essais sur les interconnexions haute tension pour la classe IAC-A
Remplacer la figure existante par la nouvelle figure suivante:
Trang 6(1) IEC 62271-200:2011
* Pour l'essai phase-terre, le constructeur est tenu de spécifier la valeur du courant
* Pour l'essai phase-phase, le courant est 87 % du courant de courte durée assigné
(2) La durée peut être déclarée par les constructeurs, prenant en compte le réglage en temps de la protection
Figure AA.6 – Sélection des essais sur les interconnexions haute tension
pour la classe IAC-A
IEC
Oui
Non
Protection des opérateurs (portes ouvertes
à l'appareillage HT)
Interconnexions
HT
Protection par fusibles limiteurs HPC
Essai phase-terre
ou phase-phase Valeures réduites (1) + (2)
Pas
d’essai
interconnexions isolées avec écran relié à
la terre soumises
à essai de type (voir AA.6) Non
Protection par disjoncteur
interconnexions isolées solides (voir AA.6)
Essai triphasé
Courant total et durée
réduite (2)
Non (pas de protection) Oui
Non
Essai phase-terre
ou phase-phase Courant réduit (1) et durée totale
Essai triphasé Courant total et durée totale
Oui Pas
d’essai
interconnexions isolées solides (voir AA.6)
Trang 7Figure AA.7 – Sélection des essais sur les interconnexions haute tension pour la classe IAC-B
Remplacer la figure existante par la nouvelle figure suivante:
Trang 8(1) Applicabilité de l'essai phase-terre ou phase-phase selon les critères de AA.5.2.1 de l'IEC 62271-200:2011
* Pour l'essai phase-terre, le constructeur est tenu de spécifier la valeur du courant
* Pour l'essai phase-phase, le courant est 87% du courant de courte durée assigné
(2) La durée peut être déclarée par le constructeur, prenant en compte le réglage en temps de la protection
Figure AA.7 – Sélection des essais sur les interconnexions haute tension
pour la classe IAC-B
Oui
Non
Protection du public (portes fermées)
Interconnexions
HT
Protection par fusibles limiteurs HPC
Essai phase-terre
ou phase-phase Valeures réduites (1) + (2)
Pas
d’essai
interconnexions isolées avec écran relié à
la terre soumises
à essai de type (voir AA.6) Non
Protection par disjoncteur
interconnexions isolées solides (voir AA.6)
Essai triphasé
Courant total et durée
réduite (2)
Non (pas de protection) Oui
Non
Essai phase-terre
ou phase-phase Courant réduit (1) et durée
totale
Essai triphasé Courant total et durée totale
Oui Pas
d’essai
interconnexions isolées solides (voir AA.6)
IEC